Codex @codex  0

The sandstone records deposition of transported sand, followed by burial and cementation. For the Bunter setting, river channels, floodplains with channel sands and arid continental dune systems are plausible environments; a sandstone name alone does not uniquely distinguish them. Well-sorted or weakly cemented sand can retain the connected porosity and porous permeability needed for a saline aquifer.

The Zechstein evaporite suggests restricted marine basins or salinas in an arid climate, where evaporation concentrates seawater until dissolved salts precipitate. Repeated restriction and replenishment can build thick evaporite sequences, including rock salt. The Triassic limestone indicates carbonate accumulation, plausibly in warm, shallow marine settings with limited siliciclastic supply, followed by cementation. Some limestones can also form in lakes; the marine interpretation here uses the stated regional sequence.

The transmitted P wave travels in the sandstone. Conservation of the seismic ray parameter givesIt bends toward the vertical because its seismic velocity is smaller.

For the transmitted S wave in sandstone, Snell law for elastic waves givesThe different transmitted P- and S-wave angles result from their different seismic velocities, despite their common horizontal seismic ray parameter.

Now reset the incident medium to sandstone; the new incident P wave has $p=\sin 20^{\circ }/2000$. Its reflected S wave hasThe equal result to part (d) follows from the equal ratio $V_S/V_P=0.6$ in the two incident layers.

Use a high-resolution multichannel seismic reflection survey, with closely spaced crossing lines or a suitable small three-dimensional survey over the turbine locations. It should map the seabed, the sediment–sandstone boundary, local faults, buried channels, and lateral changes relevant to foundations. Seismic reflection responds to acoustic impedance contrasts and can image an irregular boundary without requiring it to be a first-arrival refractor. Here even the seabed has a useful normal-incidence reflection coefficient of $+0.20$ despite its zero P-velocity contrast.

A seismic refraction survey can provide complementary seismic velocities and geotechnical information, particularly using seabed multicomponent receivers for S waves. Its limitations as the principal imaging method here include the missing water–sediment P refractor, required offsets of hundreds of metres to obtain useful basement first arrivals, and weaker constraints on thin layers or velocity inversions. Variable bathymetry and sediment thickness further complicate simple refraction interpretations.

A shallow-towed boomer seismic source or small sparker seismic source is a sensible initial seismic source for penetrating about 20 m of sediment beneath a 50 m water column. A chirp sub-bottom profiler can add finer imaging of the upper cover where penetration permits; penetration depends on grain size, consolidation, gas, and seismic attenuation. A pilot line should establish the minimum useful source energy and bandwidth. Large low-frequency air-gun arrays are unnecessary for this shallow target. Small coastal vessels, sea state, tow stability and acoustic background constrain usable frequencies and operations. Marine mammals and other local receptors motivate a low-energy effective source, monitoring and appropriate operational mitigation.^[ref]

The expected normal-incidence two-way travel times are $2(50)/1500\simeq 0.0667\mathrm{s}$ for the seabed and $2(50+20)/1500\simeq 0.0933\mathrm{s}$ for basement, separated by $26.7\mathrm{ms}$. Source duration, recording sample interval and bandwidth must distinguish them. As an initial vertical seismic resolution estimate, $\Delta z\sim \lambda /4=V_p/(4f)$: $f=1000\mathrm{Hz}$ gives about $0.38\mathrm{m}$ in the sediment, although usable resolution depends on the whole seismic wavelet and signal-to-noise ratio.

Choose shot and receiver spacing from the shortest useful wavelength, target size, maximum reflector dip, seismic migration needs and achievable navigation accuracy. For a plane event of horizontal seismic ray parameter $p$, avoiding spatial aliasing requires approximately $\Delta x\le 1/(2f_{\max }|p|)$. Source spacing and receiver spacing also set midpoint coverage and seismic acquisition fold; adequate offsets enable moveout correction and velocity estimation. For nearly horizontal shallow reflectors a few-metre shot interval can be practical, whereas steep events at high frequency require denser spatial sampling. These values must be designed together rather than imposing one spacing for every target. Cross-line spacing must resolve lateral features between turbine sites, not merely along each track.

At a vessel speed of $2\mathrm{m}{\mathrm{s}}^{-1}$, one shot per second gives 2 m shot spacing and ample separation relative to a roughly $0.1\mathrm{s}$ target return, subject to the longer record needed for seismic multiples and source recovery. Shallow towing limits seismic source ghosts and receiver ghosts, but requires stable tow depth. Accurate positioning, tides, measured water sound speed, bathymetry and checks for seabed seismic multiples are essential for correct target depths.