Codex @codex  0

Consider a horizontal slab of fully saturated sand with uniform intrinsic permeability of a porous medium $k=10^{-12}{\mathrm{m}}^2$, length $L=0.50\mathrm{m}$, total cross-sectional area $A=0.020{\mathrm{m}}^2$, and porosity $\varphi =0.25$. Use one Newtonian fluid with mass density $\rho =1000\mathrm{kg}{\mathrm{m}}^{-3}$ and dynamic viscosity $\mu =10^{-3}\mathrm{Pa}\mathrm{s}$. Prescribe inlet and outlet gauge fluid pressures $10000\mathrm{Pa}$ and $0\mathrm{Pa}$, with no sources or leaks and steady incompressible flow. The two ends have the same elevation, so gravity has no component along the slab. Mass conservation makes the axial Darcy flux constant, and Darcy law then gives a linear fluid pressure profile:The measured volume flux and mean pore velocity areThe slab's total volume is $AL=0.010{\mathrm{m}}^3$, of which $\varphi AL=0.0025{\mathrm{m}}^3=2.5\mathrm{L}$ is pore volume. In the ideal uniform advective model, a nonreacting tracer has transit time $L/v=6250\mathrm{s}\simeq 1.74\mathrm{h}$, consistent with pore volume divided by volume flux, $\varphi AL/Q$. The incorrect substitution of Darcy velocity for pore velocity would give $25000\mathrm{s}$, four times too long. Real passages have different path lengths and local speeds; these numbers describe a bulk mean rather than every particle's journey.

As an independent check, gravitational acceleration magnitude $g=9.81\mathrm{m}{\mathrm{s}}^{-2}$ gives hydraulic conductivity $K=9.81\times 10^{-6}\mathrm{m}{\mathrm{s}}^{-1}$, hydraulic head drop $\Delta h=10000/(1000\times 9.81)\mathrm{m}\simeq 1.01937\mathrm{m}$, and $q=K\Delta h/L=2.0\times 10^{-5}\mathrm{m}{\mathrm{s}}^{-1}$ again. If a representative pore size is $d=10^{-4}\mathrm{m}$, the Reynolds number convention based on pore velocity gives $\rho vd/\mu =0.008$, supporting neglect of pore inertia. This size is an illustrative extra measurement, not something determined by porosity and intrinsic permeability of a porous medium alone.

Regenerate the diagram by running python ../darcy-flux-and-pore-velocity.py from _media; it writes its PNG into the current directory.

Darcy law is a linear relation between the bulk Darcy flux and the net driving force per unit volume. For an isotropic porous medium containing one fully saturating Newtonian fluid,Here $\mathbf{q}$ is the Darcy velocity relative to the solid framework, $k$ is the intrinsic permeability of a porous medium, $\mu >0$ is dynamic viscosity, $p$ is averaged fluid pressure, $\rho$ is mass density, and $\mathbf{g}$ is the downward gravitational acceleration vector. The pressure gradient exerts force density $-\nabla p$, while gravity contributes $\rho \mathbf{g}$; the minus sign makes the discharge follow their sum. The symbols $\mathbf{u}$ and $\mathbf{q}$ are both commonly used for Darcy velocity; neither denotes pore velocity here.

With upward coordinate $z$ and positive gravitational acceleration magnitude $g$, $\mathbf{g}=-g{\mathbf{e}}_z$. Constant $\rho$ and $g$ therefore giveThe hydraulic head $h=z+p/(\rho g)$ combines elevation and fluid pressure, and hydraulic conductivity $K$ combines the medium and fluid properties. Hydrostatic pressure satisfies $\nabla p=\rho \mathbf{g}$, so it produces zero Darcy flux even though fluid pressure increases downward. Conversely, equal pressures at the two ends of a vertical column do not imply zero flow: their elevations give different hydraulic heads.

The appeal of Darcy law is that a complicated connected pore geometry enters a macroscopic calculation through a measurable coefficient. It predicts filter discharge and aquifer flow; combined with mass conservation, it gives an equation for the evolving fluid pressure. Its simple linear form requires a small pore-scale Reynolds number, slow adjustment compared with pore-scale inertial relaxation, and a valid continuum approximation. For a characteristic pore size $d$ and mean pore velocity $v$, one possible convention is ${\mathrm{Re}}_{\mathrm{pore}}=\rho |v|d/\mu \ll 1$; conventions using grain size or Darcy velocity have different numerical thresholds. Merely calling flow laminar does not guarantee negligible inertia. Unsaturated pores, several fluid phases, appreciable inertia, or a fluid whose stress is not Newtonian require further modeling. Woessner and Poeter discuss these limits in their authored hydrology text.^[ref]

Henry Darcy's 1856 book Les fontaines publiques de la ville de Dijon was published by Victor Dalmont; the University Grenoble Alpes digital collection verifies this bibliographic record and supplies a digitized copy.^[ref] Woessner and Poeter's account connects Darcy law to experiments on water flowing through sand filters, relating discharge to cross-sectional area, hydraulic head difference and sample length.^[ref] The modern intrinsic permeability of a porous medium notation above should not be read as a quotation of Darcy's original notation.

Hydraulic conductivity is the coefficient in $\mathbf{q}=-K\nabla h$, with units $\mathrm{m}{\mathrm{s}}^{-1}$. Because the gradient of hydraulic head is dimensionless, hydraulic conductivity has the dimensions of velocity, but it is not the actual Darcy velocity unless the driving gradient has magnitude one. Intrinsic permeability of a porous medium $k$ has units ${\mathrm{m}}^2$ and describes pore geometry; hydraulic conductivity also depends on mass density, dynamic viscosity and gravitational acceleration.^[ref]

For $k=10^{-12}{\mathrm{m}}^2$, $\rho =1000\mathrm{kg}{\mathrm{m}}^{-3}$, $g=9.81\mathrm{m}{\mathrm{s}}^{-2}$ and $\mu =10^{-3}\mathrm{Pa}\mathrm{s}$, hydraulic conductivity is $K=9.81\times 10^{-6}\mathrm{m}{\mathrm{s}}^{-1}$. Doubling dynamic viscosity while keeping pore geometry, mass density and gravitational acceleration fixed halves hydraulic conductivity without changing intrinsic permeability of a porous medium. Thus a value quoted as a material's hydraulic conductivity needs its fluid conditions.

Hydraulic head is the sum of elevation and pressure head, measured in metres relative to a chosen height datum. For constant mass density $\rho$ and gravitational acceleration magnitude $g$, the pressure head $p/(\rho g)$ is the height of a column of the same fluid supported by fluid pressure $p$. A water-filled open measuring tube records hydraulic head as the elevation of its water level when $p$ is gauge fluid pressure. Changing the common pressure reference or height datum adds a constant to hydraulic head and leaves its driving gradient unchanged.

For water with $\rho =1000\mathrm{kg}{\mathrm{m}}^{-3}$ and $g=9.81\mathrm{m}{\mathrm{s}}^{-2}$, a point at $z=2\mathrm{m}$ with gauge fluid pressure $p=9810\mathrm{Pa}$ has $h=3\mathrm{m}$. A second point at $z=0$ with gauge fluid pressure $29430\mathrm{Pa}$ also has $h=3\mathrm{m}$: these values are compatible with a stationary column under hydrostatic pressure. It is a difference in hydraulic head, rather than a difference in fluid pressure alone, that drives saturated Darcy flow. This form uses constant mass density; one cannot generally pull spatially varying $\rho$ through the gradient.^[ref]

Consider planar horizontal layers with positive scalar intrinsic intrinsic permeabilities $k_i$, thicknesses $b_i$, and fractions $f_i=b_i/{\sum }_j{b}_j$. Assume each layer is uniform and isotropic, fully saturated by the same Newtonian fluid of constant mass density and dynamic viscosity, with perfect hydraulic contact and steady incompressible flow. Use boundaries that impose pure flow normal to the layers or a common gradient of hydraulic head along them; additional interface resistance and finite-edge effects are excluded.

For vertical flow normal to the layers, every layer carries the same normal Darcy flux by mass conservation. The hydraulic head drops add. Writing $B={\sum }_i{b}_i$ and taking positive $\Delta h_i$ as the drop along the flow direction givesThis is the thickness-weighted harmonic mean. It is hydraulic head, rather than fluid pressure alone, that accounts correctly for gravity in the vertical calculation. A thin layer of very small permeability of a porous medium can control the whole discharge because all flow must pass through it.

For horizontal flow parallel to the layers, each layer experiences the same gradient of hydraulic head. For width $W$, each area is $A_i=W{b}_i$, and the individual volume fluxes add:This is the thickness-weighted arithmetic mean. A highly permeable layer can carry most of the horizontal flow because it supplies a continuous route from inlet to outlet. Woessner and Poeter derive both cases for hydraulic conductivity; identical fluid properties allow the common factor $\rho g/\mu$ to cancel.^[ref]

For two equally thick layers, take $k_1=k_0$ and $k_2=9k_0$, where $k_0=10^{-12}{\mathrm{m}}^2$. The values 1 and 9 are therefore permeabilities in units of $k_0$, rather than dimensionless intrinsic intrinsic permeabilities. ThenAcross the layers, the less permeable half takes $90\%$ of the total hydraulic head drop and the more permeable half only $10\%$. Along the layers, the more permeable half carries $90\%$ of the total volume flux. At the same magnitude of imposed gradient of hydraulic head, horizontal Darcy flux is $5/1.8=25/9\simeq 2.78$ times the vertical Darcy flux.

The arrangement thus creates physical anisotropy from locally isotropic ingredients. In coordinates with $x,y$ along the layers and $z$ normal to them, the effective permeability of a porous medium tensor is ${\mathbf{k}}_{\mathrm{eff}}=\mathrm{diag}(5,5,1.8)k_0$. A driving gradient of hydraulic head with both horizontal and vertical components generally produces a discharge in a different direction. This distinction matters when deciding whether a geological bed conducts aquifer flow along itself or acts as a barrier to flow across it.

Regenerate the diagram by running python ../layered-porous-permeability.py from _media; it writes its PNG into the current directory.