Codex @codex  0

Use a rock strength envelope: at each depth plot the smaller differential stress needed for frictional failure and for sustained ductile material creep at a specified strain rate. Shallow rock generally strengthens with depth because effective confining pressure increases; sufficiently deep hot rock weakens because thermally activated material creep becomes efficient.

At shallow depth, Byerlee's law or a Mohr-Coulomb failure criterion gives a relation of the formwhere $C$ is cohesion, $\mu$ a coefficient of friction, ${\sigma }_n$ the compressive normal stress and $P_f$ the pore pressure. Increasing overburden generally increases effective stress, hence the frictional strength. Conversion from fault shear stress to differential stress depends on the stress regime and fault orientation; a sketch should not label a universal numerical slope. High pore pressure or weak fault gouge can lower the frictional strength substantially.

A simplified dislocation creep relation isHere $Q$ is activation energy, $V^{\ast }$ activation volume, $R$ the molar gas constant and $T$ absolute temperature; $A$ and $n$ depend on composition and deformation mechanism. At fixed strain rate, increasing temperature usually decreases the required stress strongly. The competing effects of pressure, water weakening of rocks, grain size and composition also matter. The intersection with frictional failure gives a brittle-ductile transition, not a change from solid to liquid.

For the Indian continental interior, a useful first sketch has an upper-crustal strength peak, a weaker lower continental crust, and renewed strength in lithospheric mantle beneath the Moho. Quartz-bearing rocks can undergo ductile material creep at conditions where colder, drier olivine-rich mantle retains appreciable strength. This creates a possible two-peak, or “jelly sandwich”, rock strength envelope. With further depth the mantle also weakens. A cold craton can retain strong lithospheric mantle to much greater depths than a tectonically heated continental region.

For the central Pacific, show thin mafic oceanic crust above a relatively thick layer of strong lithospheric mantle. There need not be a conspicuous weak lower-crustal layer. Much of the integrated strength can reside below the Moho, with a broad strength peak followed by ductile weakening towards the asthenosphere. Cooling and age control the thickness: young hot oceanic lithosphere would give a much shallower and weaker profile than an old central-Pacific plate.

The plotted Moho depths of about 38 km and 7 km, and all plotted stresses, are illustrative assumptions. “India” alone does not specify a unique geothermal gradient, water content or strain rate, and the Pacific includes plates of different ages. The robust comparison is the possible crust–mantle layering in a continent versus the thin oceanic crust and mantle-dominated strength of an old oceanic plate. The Moho is a compositional boundary; neither it nor the deepest small plotted strength is automatically the seismic lithosphere-asthenosphere boundary.

Left: ordinary frictional strengthening with depth followed by thermally activated material creep. Right: a very weak shallow faulted layer above a narrow strong region near 10 km, followed by essentially the same weakening material creep branch. These are the shapes actually plotted in Figure 2. The right curve is not a strong upper crust over a uniformly weak lower crust; neither diagram displays a second mantle-strength peak.

For the left curve, increasing overburden increases the effective normal load on faults. A schematic Coulomb friction law iswhere $C$ is cohesion, $\mu$ the coefficient of friction, ${\sigma }_n$ the compressive normal stress and $P_f$ the pore pressure. With ordinary rock friction and approximately hydrostatic pressure, ${\sigma }_n-P_f$ increases roughly linearly with depth. The stress needed for frictional sliding therefore increases, as in the straight shallow branch. Byerlee's law summarizes the relatively high friction found in many laboratory rocks.^[ref]

At higher temperature, dislocation creep or another ductile mechanism accommodates the imposed deformation at lower stress. For example,Here $\dot{ϵ}$ is strain rate, $Q$ an activation energy, $R$ the molar gas constant and $T$ absolute temperature. At fixed strain rate, increasing $T$ lowers the required stress. The operative envelope is approximately $\min ({\sigma }_f,{\sigma }_d)$, expressed in a consistent stress convention; the peak marks the brittle-ductile transition. This accounts for the left curve's peak near 100 MPa and its decline toward small strength by about 20 km.

For the right curve, normal high-friction sliding with depth-independent fluid-pressure ratio cannot explain the nearly vertical weak shallow branch. Plausible weakening includes high pore pressure tracking the overburden, low-friction fault gouge, or a connected network of pre-existing weak faults. Roughly constant small ${\sigma }_n-P_f$ yields roughly constant small frictional strength. The abrupt increase near the base of this layer requires a change of conditions: for example, the weak fluid-rich fault network terminates or becomes discontinuous, leaving stronger intact or less altered rock below. A change in mineralogy or deformation localization can also give a contrast. Simply saying “there are fluids” does not explain the return to high strength. Below the strong region, thermal material creep again lowers the strength.

The figure alone does not identify the weakening mechanism or a particular lithological boundary. In particular, a 10 km strength maximum is not evidence for a 10 km deep Mohorovičić discontinuity. The strong-fault/weak-fault evidence and the distinction between fault strength and surrounding crustal strength are discussed in Stress orientations at intermediate angles to the San Andreas Fault, California by Jeanne L. Hardebeck and Andrew J. Michael.

Support for the left curve comes from high laboratory friction and substantial in situ differential stress; support for the right curve comes from low inferred fault traction, weak fault materials or high pore pressure. No single observation directly measures the whole plotted envelope.

For the left, stronger shallow-crust model:

For the right, weak shallow-layer model:

To discriminate, measure the strength-controlling quantities through depth and across both faults and their surroundings. Obtain borehole stress, pore pressure and temperature profiles where feasible; use borehole breakouts and hydraulic tests to constrain effective stress. Recover fault and host rocks and test their friction and material creep at relevant fluid conditions. The right curve specifically predicts an end to the shallow weakening near its sharp rise: investigate changes in permeability of a porous medium, alteration and fault gouge with depth, rather than testing only a surface sample.

Combine those measurements with heat flux transects, magnetotelluric sounding for conductive fluids, accurate earthquake depths and focal mechanisms, and GNSS or InSAR observations of deformation. The latter can help constrain the depth distribution of locking and postseismic relaxation, but neither locking nor seismicity alone gives absolute strength. Earthquake stress drop is a change in stress, not the pre-event stress. Low heat flux can also reflect heat transport or transient weakening; high electrical conductivity can have causes other than free water. A joint explanation of all these data is needed to choose between the models locally.

A depth-dependent estimate of the differential stress a rock column can sustain at a specified strain rate, composition, thermal structure and fluid state. In a simple competing-mechanism model, failure occurs by whichever of frictional sliding and ductile material creep requires the lower stress, giving the displayed lower envelope.

Effective confining pressure generally increases frictional strength with depth. In contrast, a power-law creep model $\dot{ϵ}=A{\sigma }^n\exp [-(Q+P{V}^{\ast })/(RT)]$ gives ${\sigma }_{\mathrm{creep}}=(\dot{ϵ}/A{)}^{1/n}\exp [(Q+P{V}^{\ast })/(nRT)]$. At fixed strain rate, the rise of temperature along a geothermal gradient generally lowers the required creep stress. Their crossing is a brittle-ductile transition, while composition changes at the Moho can produce additional peaks. A rock strength envelope is not uniquely determined by depth or by the labels “continental” and “oceanic”.