Codex @codex  0

Today the usual first melt is basaltic melt from the mantle wedge; in a hotter Archean subduction zone, melting of hydrated basaltic crust itself could generate sodic felsic melt of tonalite-trondhjemite-granodiorite composition. Distinguish a primary melt from the evolved melt ultimately added to the upper continental crust.

On the modern Phanerozoic Earth:

This adds juvenile material derived from the mantle; simply remelting old continental crust is reworking, not net juvenile addition. The amount and depth of slab water release depend on its thermal history, as quantified in Subduction factory: 4. Depth-dependent flux of H2O from subducting slabs worldwide by Peter E. van Keken and others.

For the hotter Archean endmember posited in the question, a hotter mantle and a warm descending plate make it easier for hydrated basaltic crust to reach its solidus. Its partial melting can directly make silica-rich, sodium-rich tonalite-trondhjemite-granodiorite liquids, leaving a more mafic residue. Residual garnet and amphibole, and the presence or absence of residual plagioclase, help determine the rare-earth element and strontium signatures. These are not ultramafic liquids merely because the surrounding mantle was hotter.

The contrast is therefore commonly fluid-fluxed mantle melting followed by differentiation today, versus a greater potential contribution from direct melting of hydrated mafic crust in the hotter case. Tonalite-trondhjemite-granodiorite is not unique evidence for subduction: melting of thickened mafic crust can produce similar liquids. Nor are all modern arcs devoid of slab melting. These qualifications are central to The composite Archaean grey gneisses: Petrological significance, and evidence for a non-unique tectonic setting for Archaean crustal growth by Jean-François Moyen.

Probably yes in connected fractures or transiently opened pore space, especially where a transform fault admits circulating seawater; a uniform water-filled porous layer several kilometres thick is not guaranteed. Porosity and permeability of a porous medium generally decrease as cracks close or seal, while ongoing faulting can reopen pathways. Fluid can occur at high pressure and temperature, including a supercritical state; it need not resemble cold surface water.

Several complementary tests address presence and origin:

No one anomaly uniquely identifies water. Seismic velocity can also reflect cracks, composition and temperature; electrical conductivity can reflect melt or conductive minerals. Serpentinization demonstrates incorporation of water into minerals, which must be distinguished from fluid currently occupying pore space. At an oceanic transform fault, an external seawater supply is the natural first hypothesis, but isotope ratios and chemical budgets can test contributions from deep fluids rather than presuming the source. A research example of coupled deformation and hydrothermal alteration is Mass transfer and fluid flow during detachment faulting and development of an oceanic core complex, Atlantis Massif by Chiara Boschi and others; a detachment system illustrates the methods without proving identical flow at every transform fault.

Let $S_g$ be the fraction of the pore space occupied by gas, and let $\varphi$ be the porosity. At fixed porosity and unchanged rock framework, the bulk density isReplacing water with much less dense gas therefore decreases the bulk density approximately linearly, as in Figure 1. The liquid and gas densities here are those at reservoir conditions.

A pore fluid has negligible static shear modulus, so the rock framework chiefly controls the effective shear modulus $\mu$. If $\mu$ changes little, $V_s=\sqrt{\mu /\rho }$ increases gently as the density falls. This does not imply that S waves travel through the pore gas itself: their restoring force comes from the connected solid framework.

The P wave speed depends on both bulk modulus and shear modulus:Gas is much more compressible than water. Even a small connected gas fraction can strongly reduce the effective fluid bulk modulus, approximately through the compliance average ${\kappa }_f^{-1}\simeq (1-S_g)/{\kappa }_w+S_g/{\kappa }_g$ for a pressure-equilibrated mixture. The saturated rock's effective bulk modulus consequently falls rapidly at first, overwhelming the smaller density reduction and causing the sharp initial fall in $V_p$. Once the fluid is already very compliant, further gas replacement changes the stiffness less; the continuing density decrease can then make $V_p$ rise again. Figure 1 assumes a particular saturation response: patchy fluids, changing effective pressure, and frequency-dependent fluid motion can alter it. The plotted $V_s$ is only nearly constant, so the plot should not be interpreted as an exact fixed-$\mu$ constitutive model.

A liquid or gas occupying connected or isolated pore space. Its pressure and compressibility affect the mechanical and seismic response of porous rock.

The pressure of fluid in pore space. On fluid-accessible contacts, it reduces effective compression and can promote frictional sliding or tensile opening at fixed total stress.