Codex @codex  0

The change of output electric current per change of input electric potential difference, evaluated at an operating point with the other terminal conditions specified. In a small-signal model, $i_{\mathrm{out}}=g_m{v}_{\mathrm{in}}$ describes this contribution; transconductance has the dimensions of electrical conductance.

An original teaching model exposes the roles of input loading, output loading and the supply. Choose a small-signal model with positive input electrical resistance $r_i$, transconductance $g_m>0$, and output electrical resistance $r_o>0$. Its controlled output current source draws $g_m{v}_i$ from the output node toward the reference node. This chosen sign gives an inverting voltage gain; it is not the historical contact circuit's sign convention.

Assume a fixed operating point, negligible reverse coupling, a frequency range where coupling capacitors pass the signal, and negligible other capacitances and transit delays. A collector resistor $R_D$ connects the output to a steady ideal supply $V_{DD}$; an external electrical load $R_L$ is coupled through a capacitor, so it draws no direct current. The input source has series electrical resistance $R_s$. All voltages below are small departures from the operating point. An ideal fixed supply has zero incremental voltage and therefore becomes the reference node in the small-signal model.

Define $R_O=R_D\parallel r_o$ and $R_P=R_O\parallel R_L$, where $a\parallel b=ab/(a+b)$. Input voltage division and output Kirchhoff's current law giveConsequently the port voltage gain, overall source-to-output voltage gain, and load current gain magnitudes areThis current gain uses load electric current, not all the controlled-source electric current. It is also a different port definition from the historical emitter-to-collector current gain. Larger $R_s$ attenuates the input; smaller $R_L$ attenuates the output.

For a sinusoid input signal, use root mean square voltages. The power gain from accepted input signal power $P_i=v_i^2/r_i$ to useful load power $P_L=v_o^2/R_L$ isUnlike $|A_i|$, this tends to zero as either $R_L\to 0$ or $R_L\to \infty$. Differentiation givesThus matching the output electrical load maximizes delivered power in this unilateral resistive model. For fixed source voltage, input loading multiplies $P_L$ by $[r_i/(R_s+r_i){]}^2$; the accepted-input power gain above excludes the loss in $R_s$.

Choose $r_i=R_s=1\mathrm{k\Omega }$, $g_m=2\mathrm{mS}$, $r_o=20\mathrm{k\Omega }$, and $R_D=2\mathrm{k\Omega }$. Then $R_O=20/11\mathrm{k\Omega }$. With $R_L=2\mathrm{k\Omega }$ and $v_s=20\mathrm{mV}$ root mean square, the input is $10\mathrm{mV}$ and the inverted output has magnitude $19.0476\mathrm{mV}$ root mean square. Hence $P_i=0.100\mu \mathrm{W}$ and $P_L=0.181406\mu \mathrm{W}$: $G_P=1.81406$. These are calculated values of the chosen model, not historical measurements.

With the same parameters but $R_L=100\Omega$, $|A_i|=1.89573$ while $G_P=0.359381<1$. At $R_L=10\mathrm{k\Omega }$, $|A_v|=3.07692$ while $G_P=0.946746<1$. Neither current gain nor voltage gain alone establishes power gain.

For the direct current load line in the figure, choose $V_{DD}=6\mathrm{V}$, $I_Q=1\mathrm{mA}$ and $V_Q=4\mathrm{V}$, consistent with $V_Q=V_{DD}-R_D{I}_Q$. Locally extend the model as $I=I_Q+g_m{v}_i+(V-V_Q)/r_o$. With the external electrical load isolated at direct current, its intersection with $I=(V_{DD}-V)/R_D$ is $V=V_Q-g_m{R}_O{v}_i$. Keeping $|v_o|$ small compared with the available voltage headroom is essential; extrapolation to arbitrarily large signals would be unphysical.

At the chosen operating point the collector supply delivers $V_{DD}{I}_Q=6\mathrm{mW}$: $2\mathrm{mW}$ is dissipated in $R_D$ and $4\mathrm{mW}$ in the output device. Under a small signal, that energy flow is redistributed to provide load power. The incremental controlled current source hides the supply's steady energy flow; it does not create energy. A real complete amplifier also needs its input biasing network and has further losses. This calculation establishes neither its total efficiency nor a universal law for point-contact transistors.