Boiling Created 2026-10-18 Updated 2026-11-05
Boiling is vaporization through the formation and growth of vapor bubbles within a liquid. It differs from surface evaporation, which can occur without bubbles in the bulk. At equilibrium, the boiling point of a pure liquid is set by equality of its saturation vapor pressure and the external pressure.
A real bubble must also overcome local hydrostatic pressure and the capillary pressure of its curved surface. Creating the interface costs energy, giving a nucleation barrier; a smooth clean vessel can therefore permit superheating. Surface cavities and boiling chips supply sites where bubbles form more readily. The observed onset depends on these sites and heating conditions, while the equilibrium boiling point remains a property specified at the chosen pressure.
Boiling chip Created 2026-10-18 Updated 2026-11-05
A boiling chip is a small solid piece with cavities or a porous surface that supplies sites for heterogeneous nucleation of vapor bubbles in a heated liquid. Gas trapped in a cavity can help an incipient bubble survive the capillary pressure that would collapse a sufficiently small isolated bubble.
Many active sites encourage repeated bubble release, reducing the large, irregular boiling events associated with delayed nucleation and superheating. The chip changes the route by which boiling begins; it does not materially redefine the liquid's equilibrium boiling point. Its action is therefore understood through interface formation and bubble growth, rather than through a chemical conversion of the solvent.
Boiling-point elevation Created 2026-10-31 Updated 2026-11-05
Dimethyl ether 2026-11-05
Dimethyl ether, also called methoxymethane, is an ether with an oxygen atom bonded to two methyl groups. Its structural formula is and its molecular formula is . It is a constitutional isomer of ethanol: the atoms have the same inventory but different connectivity.[ref]
The oxygen connectivity gives a useful molecular comparison. Ethanol contains an oxygen–hydrogen bond; dimethyl ether does not. Thus the two chemical structures present different possibilities for hydrogen bonding, even though weighing equal numbers of their molecules would not distinguish their common elemental formula.
Their physical identity can be tested by measurements beyond composition. NIST tabulates a normal boiling point near , approximately , for dimethyl ether. This illustrates why a small carbon-containing molecule can be a gas under ordinary room conditions: phase behavior follows its interactions and external conditions, rather than molecular formula alone.[ref]
NIST Chemistry WebBook, SRD 69. Dimethyl ether, CAS115-10-6, Phase change data: boiling-point compilation near248.2–248.3K; record C115106.
At a stated external pressure, the boiling point of a pure liquid is the temperature at which its saturation vapor pressure equals that pressure. A vapour bubble inside the liquid must also withstand the hydrostatic head and any capillary pressure; the simple free-surface boiling-point rule neglects those small local corrections.
Increasing external pressure raises the usual boiling point, while lowering it lowers the boiling point. The Clapeyron equation explains the direction:for ordinary vaporization with positive latent heat and a larger vapour specific volume. Consequently water can boil below its usual open-vessel temperature at altitude or under partial vacuum, and above it in a sufficiently pressurized vessel.
Composition also matters. A nonvolatile dissolved solute generally lowers the solvent's vapour pressure and produces boiling-point elevation at fixed external pressure. A volatile second component can instead raise or lower the boiling temperature according to the mixture's phase equilibrium; an azeotrope is a useful warning against applying the nonvolatile-solute rule to every mixture.
Finally, distinguish the equilibrium boiling point from the observed onset of bubbles. A smooth clean vessel or a shortage of nucleation sites can permit superheating; agitation or suitable existing sites can make boiling begin nearer equilibrium. Heating power mainly controls the rate of sustained boiling under otherwise fixed conditions, rather than setting an arbitrary new equilibrium boiling point. A thermometer must be placed to measure the intended liquid or saturated vapour region, rather than a locally overheated wall.
Steam distillation 2026-11-05
Steam distillation is co-distillation with water, in which water vapor carries volatile material into a laboratory condenser and receiver. It can recover volatile organic compounds from less volatile material without requiring the isolated compound to reach its own pure-component boiling point. The University of York's teaching apparatus combines material and water in a boiling flask connected to a distillation head, condenser and collection flask.[ref]
Steam distillation in University of York Chemistry Teaching Labs. Introduction and apparatus description
A useful ideal case is liquid immiscibility: two separate liquid phases remain present, and each supplies approximately its pure-component vapor pressure. Their sum reaches the external pressure at boiling:Because both terms contribute, the required temperature can be below either pure liquid's boiling point at that same external pressure. This limit assumes both liquid phases persist and neglects mutual solubility and vapor nonideality.
For invented equilibrium data, let the water and organic partial pressures be and at the boiling temperature. The vapor mole ratio is . If the organic compound has molar mass and water is approximated by , the condensed mass ratio isThis is an equilibrium model, not an extraction yield.
A 1964 methanol dehydrogenase study used steam distillation before a formaldehyde assay. Its authors explicitly left unresolved whether the product had been free or bound before separation.[ref]
The microbial oxidation of methanol. 2. The methanol-oxidizing enzyme of Pseudomonas sp. M 27 by C. Anthony and L. J. Zatman. Page 620 and Table 2, product separation and interpretation
Recovering a volatile product and establishing its earlier molecular state are different experimental claims. Superheating Created 2026-10-03 Updated 2026-11-05
Superheating is persistence of a phase above the equilibrium temperature at which a higher-temperature phase becomes favorable. The familiar case is a liquid above its boiling point at the imposed pressure, although delayed melting can also be discussed as superheating.
The liquid can remain in a metastable state because producing a vapor bubble costs interfacial energy. A sufficiently large bubble overcomes the nucleation barrier and grows, converting the liquid and consuming latent heat. Smooth clean containers can delay nucleation, while cavities and boiling chips provide heterogeneous nucleation sites. The observed temperature of sudden bubble formation therefore need not equal the equilibrium boiling point. The amount of superheating is a kinetic and preparation-dependent observation, rather than a new equilibrium phase boundary.