 Simply supported beam

A simply supported beam is prevented from moving transversely at its two supports while its ends remain free to rotate. In the small-deflection Euler-Bernoulli beam equation, a uniform span $0\le x\le L$ with transverse displacement $w(x)$ and positive beam flexural rigidity $B=EI$ has the support boundary conditionsHere $E$ is Young's modulus and $I$ is the second moment of area about the bending axis. The second pair expresses zero applied endpoint bending moment, since $M=-B{w}^{\prime \prime }$ in the convention used here. It does not set the endpoint beam cross-section rotation or slope to 0. A clamped boundary condition instead constrains both displacement and slope.

For an original derivation, apply a downward central point force $P$ and take $w$ positive downward. Assume small elastic deflections, constant $B$ and no axial preload. Symmetry and force balance give an upward reaction $P/2$ at each support. On the left half, the bending moment is $M(x)=Px/2$, so $w^{\prime \prime }=-Px/(2B)$. Integrate twice, using $w(0)=0$ and the symmetry condition $w^{\prime }(L/2)=0$, to obtainThus the midspan compliance of a simply supported beam isThe endpoint slopes are $w^{\prime }(0)=P{L}^2/(16EI)$ and $w^{\prime }(L)=-P{L}^2/(16EI)$: they are generally nonzero. This support geometry and central-load formula are used to infer material stiffness from a three-point bending test.^[ref]

The moment-free natural boundary condition for a beam also follows from the principle of virtual work. For a central load, the total potential energy is $\Pi [w]=\frac{1}{2}{\int }_0^{L}B(w^{\prime \prime }{)}^{2}dx-Pw(L/2)$. An admissible virtual displacement $\eta$ satisfies $\eta (0)=\eta (L)=0$, while its endpoint first derivatives remain free. Two integrations by parts produce the boundary contributionThe terms multiplying $\eta$ vanish because the endpoint displacements are prescribed. Arbitrary endpoint values of ${\eta }^{\prime }$ then require $B{w}^{\prime \prime }=0$ there. The free end rotation and zero end moment are conjugate parts of the same variational boundary condition.

Clamping both ends changes the central-load deflection to $P{L}^3/(192EI)$, one quarter of the simply supported value for the same $P,L,E,I$. It introduces endpoint reaction moments; it does not merely rename the same support. The clamped-beam Green function provides the corresponding fourth-order boundary-value solution. The support conditions likewise determine the simply supported beam normal modes, so a static stiffness measurement and a vibration measurement must use the same mechanical support model when they are compared.

A three-point bending test places a specimen on two separated supports and applies a central force. A load cell measures force, and a midspan displacement readout measures response. A direct plunger and extensometer can measure specimen deflection separately from machine crosshead displacement, as in the published Instron fixture arrangement.^[ref] Fitting a proportional small-load segment estimates $E=L^3/(48IC)$, where $C$ is the measured incremental midspan compliance. Record support spacing, load position and cross-section dimensions with that estimate.

For stipulated $L=0.50\mathrm{m}$, rectangular width $b=20\mathrm{mm}$, thickness $h=3\mathrm{mm}$ and $E=200\mathrm{GPa}$, the second moment of area is $I=b{h}^3/12=4.5\times 10^{-11}{\mathrm{m}}^4$ and $EI=9\mathrm{N}{\mathrm{m}}^2$. An incremental $1\mathrm{N}$ central load gives $0.289\mathrm{mm}$ incremental deflection under the simply supported model, versus $0.0723\mathrm{mm}$ for the clamped model. Incremental readings remove an unchanged baseline deflection in this linear model; support settling, contact indentation and large rotations require separate interpretation.