The P wave source is normally the more useful depth source for the end members and for the stated approximately 50% gas case, because the predicted exceeds , making the reservoir-top arrival easier to identify, assuming comparable source and recording quality. For a horizontal reflector and vertical two-way travel time entirely through the homogeneous cap rock,
or for an identified S wave arrival, with times in seconds. The reservoir's own wave speed is not the overburden wave speed used in this conversion. Nonzero-offset data require moveout correction and an appropriate overburden velocity model; no numerical depth can be obtained without a measured time.
At approximately 50% gas, Figure 1 gives , , and –. Thus
The S wave reflector is then weak because its impedance is nearly matched to the cap rock. An exact impedance match, , gives : a reservoir top can exist without producing an observable normal-incidence S wave reflection. Rounding the 50% to would suggest exactly that cancellation, but the plotted line sits slightly higher. The continuous curve crosses the cap-rock value at a somewhat greater saturation; the coarse figure does not justify a precise percentage.
There is also a smaller-saturation P wave impedance match: changes sign between zero and modest gas saturation, so it must pass through zero. Thus neither source guarantees a detectable reflector at every saturation. Joint P wave and S wave observations help distinguish a weak impedance contrast from an absent reservoir; a slower S wave speed alone is no reason to prefer it when its reflected amplitude is near zero.
Peter M. Shearer Created 2026-10-20 Updated 2026-11-05
Peter M. Shearer coauthored a method for inferring focal mechanisms from P wave first-motion polarities. It varies source location and the velocity model, collecting acceptable mechanisms rather than treating every ray direction as exact.[ref]
The spread of acceptable solutions measures stability of the inference and helps distinguish real fault-orientation variation from measurement uncertainty.
For real frequency and both vertical wavenumbers , , let , , , and . With traction and particle velocity , each directional P wave/SV-wave field obeys . Direct displacement-potential substitution yields . The Hermitian part of is positive diagonal; thus forward/backward fluxes have opposite signs and mixed directional flux cross terms cancel.
In a uniform isotropic material, these scalar P-SV displacement potentials separate longitudinal P waves from vertically polarized SV-waves in an plane. They satisfy and , with compressional and shear speeds . Reversing the sign convention for changes its polarization column but not the physical P-SV directional impedance matrix or the separate modal energy fluxes.
P-to-S conversion 2026-10-25
Conversion of an incident P wave into an S wave at a material contrast. The converted arrival's relative time and amplitude can constrain subsurface structure through a receiver function, subject to the velocity model and interface geometry.
The sign of the initial direct P wave motion after instrument, component and ray-direction conventions are calibrated. It constrains the sign of at the source takeoff direction. Near-nodal arrivals and uncertain takeoff angles need special treatment.
For a stable isotropic solid in , use , . An incident P wave with frequency , tangential wavenumber and upward normal wavenumber reflects into a P potential and an SV potential , where . Vanishing of both displacements at the rigid plane gives , . Hence and . Because and , and the converted S wave propagates rather than being evanescent.
Seismic radiation pattern 2026-10-25
The dependence of radiated P wave or S wave amplitude and polarity on direction from an earthquake source. For an ideal double couple it has nodal directions, so amplitude differences between stations do not measure distance or directivity alone.
Seismic reflection 2026-10-25
The return of an elastic wave from a contrast in material properties. At normal incidence in an isotropic medium, the conventional stress-amplitude reflection coefficient is for the relevant P wave or shear-wave impedance.
Seismic wave 2026-10-25
A propagating disturbance in or along the solid Earth, including body P waves, body S waves and surface modes. A water layer supports compressional acoustic motion but not a bulk shear restoring force.
Seismology Created 2026-10-20 Updated 2026-11-05
Seismology studies elastic waves generated by earthquakes, impacts and controlled sources, and uses them to investigate planetary interiors. A seismometer converts ground motion into a recorded seismogram. Arrival times, waveforms and amplitudes then constrain both the source and the material traversed by the waves.
P waves respond to compression and S waves to shear. Their different speeds and their reflections or conversions at interfaces help distinguish layers. Locating an earthquake requires several stations because its origin time and location must be estimated along with the propagation model. A single late arrival can reflect a deeper source, a slower path or a mistaken seismic phase assignment.
Solid Earth Created 2026-09-24 Updated 2026-11-05
The Solid Earth is the rocky interior-and-surface system of Earth, including its crust, mantle and metallic core. The term includes the liquid outer core of the Earth as well as the solid inner core. Mechanical classifications overlap these compositional layers: the lithosphere contains the crust and the relatively rigid uppermost mantle.
The response also depends on timescale. The mantle supports elastic waves on seismic timescales while undergoing slow mantle flow over geological times. The outer core's liquid response prevents propagation of bulk S waves, whereas compressional P waves can propagate through it. These contrasting responses help constrain the internal structure through seismic waves.
A quantitative reference describes radial profiles of mass density and elastic wave speeds. The Preliminary Reference Earth Model, developed by Adam M. Dziewonski and Don L. Anderson, combines wave observations with global constraints such as Earth's mass and moment of inertia. Its averaged layers are a reference for interpreting departures observed in the real, laterally varying Earth.[ref]
Solid-fluid P-wave transmission coefficient Created 2026-10-14 Updated 2026-11-05
For incidence from a solid with compressional/shear speeds into a fluid of sound speed , let . The displayed coefficient multiplies the transmitted displacement field potential relative to the incident P wave potential, using the same retarded-time waveform. Snell law for elastic and acoustic waves matches the tangential slowness. Continuity of normal displacement field, zero tangential traction, and continuity of normal traction give the coefficient. It is not a displacement-amplitude coefficient: longitudinal displacement field acquires an additional ratio .
S–P time 2026-10-25
The delay between corresponding S wave and P wave arrivals. For a common uniform path of length , , cancelling earthquake origin time. Matched phase identification and an appropriate velocity model are needed to infer distance.
S-to-P conversion 2026-10-25
Conversion of an incident S wave into a P wave at a material contrast. It provides a complementary receiver function constraint because its travel-time ordering and interference with reverberations differ from P-to-S conversion.
For a planar tensile-crack seismic source, is measured from its normal. The P wave displacement is radial with the first displayed amplitude. The S wave displacement is tangential in the plane containing the observation direction and crack normal, with four alternating signed lobes and nodes at the poles and equator. Both radiative fields depend on the opening rate and vanish once opening stops; the static displacement field depends on the final opening.