Very interesting story! A predecessor to microwave transmission for trading.
How The First Ever Telecoms Scam Worked by Tom Scott (2018)
Source. Amazing how they used control signals to hide the information from officials on either side.We are at a point in history where the electrical telegraph is well established.
But people don't want to press letters one by one on a switch. They want to talk!
The first phones appear to have used telegraph lines directly.
Also wired phones don't require modulation, which likely made their development much easier than wireless voice transmission. You just send the signal as a voltage differential directly obtained from the air pressure: how the telephone works.
- www.quora.com/How-is-a-voice-transmitted-from-one-phone-to-another
- www.quora.com/How-many-wires-does-a-telephone-use/answer/Peter-Yardley-1
Basic analogue phones connected to the public exchange use two wires mainly arranged as a twisted pair to reduce noise. The voice signal is differential (the voltage in one wire equal and opposite to the other) biased above ground by 48V. Using a twisted pair reduces induced noise because the noise signal will induce an equal voltage in each wire and because the signal is transmitted as the difference the effect of the induced noise will be dramatically reduced.
Phone Intercom by Make (2014)
Source. This video illustrates will the incredible simplicity of the connection of a telephone system. Compare that to the relative complexity of wireless communication, which requires modulation.Making a Microphone Work with an Oscilloscope by Environmental Radiation LLC (2012)
Source. Not the most detailed setup, but good.ethw.org/Picturephone good article!
This section is about telecommunication systems that are based on top of telephone lines.
Telephone lines were ubiquitous from early on, and many technologies used them to send data, including much after regular phone calls became obsolete with VoIP.
These market forces tended to eventually crush non-telephone-based systems such as telex. Maybe in that case it was just that the name sounded like a thing of the 50's. But still. Dead.
Long Distance by AT&T (1941)
Source. youtu.be/aRvFA1uqzVQ?t=219 is perhaps the best moment, which attempts to correlate the exploration of the United States with the founding of the U.S. states.Not a telephone-based system, needing its own network, and was killed particularly by fax which is. Telex evolved from the Telegraph, which is a binary system at the physical layer.
Uses telephone lines, and therefore were still usable much much after the Internet made them obsolete, which is quite funny.
Teletype ASR 33 Part 10: ASR 33 demo by CuriousMarc (2020)
Source. Heinrich Hertz's main initial experiment used a spark-gap transmitter. It is not something that transmits recorded sounds like voice: it only transmits noisy beeps. And as such was used for wireless telegraphy.
Hertz Experiment on Electromagnetic Waves by Ludic Science (2015)
Source. Simplified recreation with cheap modern equipment. Uses as transmitter power source both:- a piezo igniter from a barbequeue lighter
- a more powerful home-made transformer
Hertz and Radio waves Explained by PhysicsHigh (2016)
Source. Simple schematics showing the basics of the experiments. No choice of components rationale.Modulation basically means encoding data on a carrier wave.
Image that we are at a point in history where spark-gap transmitters can send Morse code.
But now people want to send voice. How to do it?
It would not be practical without modulation: Why can't you send voice without modulation?
Basically, the antenna has to be very, very large, more comparable to wavelength. E.g. even for the higher pitches, we fall in very low frequency, so have a look at the size of some of the submarine VLF antennas! They are like football pitch sized.
Early transmitters such as the spark-gap transmitter could only send noises to send Morse code.
To send voice and music, amplitude modulation had to be developed. And a key ingredient of this is the carrier wave.
The problem is, the carrier wave needs to have somewhat high frequencies, in the hundreds of kHz TODO why. But as you might imagine, that is hard to achieve by mechanical means such as a hand cranck like Hippolyte Pixiis alternator!
Interestingly, some of the first carrier wave generators were actually mechanical, e.g. the Alexanderson alternator.
But clearly such mechanical machines were not very scalable, and soon more electronic devices were introduced, notably the vacuum tube.
Radio Wave Properties: Electric and Magnetic Dipole Antennae by Harvard Natural Sciences Lecture Demonstrations (2020)
Source. The dude lights bulbs on an antenna made of a single piece of copper, powered with EM radiation. Amazing.
Dipole antenna receiver animation
. Source. 
Dipole antenna transmitter animation
. Source. 
As well put by Wikipedia, a radio receiver has to perform three functions on the signal from the antenna:
- filtering, so you can tune the station you care about. This filters based on the frequency of the carrier wave you want. I.e. you use a bandpass filter.
- amplification: otherwise you won't be able to hear anything if the emitter is too far away
- demodulation: this means decoding the signal based on whatever way it was encoded, notably e.g. AM/FM
The first type of device that allowed sending Morse code without wires, as opposed to the wired electrical telegraph that previously existed.
Naval communications was one of the first major applications, as you can't have wires on boats!
Wireless voice transmission came about with modulation.
Spark-gap transmitter at the at the The Museum of Radio and Technology Jeri Ellsworth (2017)
Source. Marconi Spark Gap Transmitter Demonstration by Canada Science and Technology Museum (2012)
Source. Founder: Peter Armstrong
The general idea is publishing entire books with usual copyright, but with gradual updates.
ruboss.com/ documents their stack, a somewhat similar choice to OurBigBook.com as of 2021, notably Next.js. But backend in Ruby on Rails. They actually managed Apollo/GraphQL, which Ciro Santilli would have liked, but din't have the patience for.
The founder/CEO Peter Armstrong www.linkedin.com/in/peterburtonarmstrong/ He looks like a nice guy.
In leanpub you write your book in a markdown variant they call Markua, marketed as "markdown for books".
TODO is there a reference implementation that runs locally for HTML output? Or the only reference implementation is closed under leanpub?
Spec: markua.com/
Articles by others on the same topic
There are currently no matching articles.