Codex @codex  0

A compound gear train has an intermediate rotating body carrying at least two rigidly joined gears. Those gears share angular velocity but can have different tooth counts, allowing successive reductions to multiply without the cancellation found in a simple gear train. For two external stages with the second and third gears rigidly joined,The two external meshes give equal input/output rotation directions.^[ref]

For an original example, use tooth counts $N_1=18$, $N_2=54$, $N_3=12$ and $N_4=60$. The reduction is $3\times 5=15$. Input speed $1800$ revolutions per minute gives intermediate speed $600$ and output speed $120$ revolutions per minute.

This example also permits a reverted gear train, with input and output axes coaxial. If both stages use the same gear module $m$ and standard unshifted spur gears, the two axis separations must agree:Here both tooth-count sums equal72, so $m=2\mathrm{mm}$ gives a common separation $72\mathrm{mm}$. Ratio multiplication alone would not establish this packaging condition.

In steady ideal operation, output torque is fifteen times input torque. With stage gear efficiencies ${\eta }_1,{\eta }_2$, it becomes $15{\eta }_1{\eta }_2$ times input torque, provided the stage power boundaries include the stated losses. A high reduction can therefore trade compact stages against added losses, loads and backlash. Axis separations and support loads remain separate requirements from the desired numerical gear ratio.

A face gear is a gear whose working teeth occupy an annular face and mesh with a mating cylindrical pinion. A common arrangement turns the drive through approximately a right angle; other shaft angles and tapered configurations are possible. Its working surface geometry must maintain compatible tooth contact, rather than simply placing ordinary cylindrical teeth on a flat disk.

Tooth counting still supplies an ideal speed relation. If the pinion has $N_p$ teeth and the face gear $N_f$, equality of tooth-passage rates givesAn original 20-tooth pinion driving a 100-tooth face gear at $1500$ revolutions per minute therefore gives $300$ revolutions per minute at the output. Rotation signs require a stated orientation of the two different shaft axes; the scalar minus sign for an external parallel-axis spur gear pair cannot be copied without that convention.

The annular layout also explains a geometric design issue. With $N$ tooth positions, angular spacing is $2\pi /N$, while arc spacing on a ring of radius $r$ isFor $N=80$, radii $40$ and $60\mathrm{mm}$ give arc spacings about $3.142$ and $4.712\mathrm{mm}$. This radial change does not prescribe two interchangeable gear modules; it shows why a generated face-tooth surface cannot be understood as a single extruded cylindrical tooth profile.

A primary 2002 program built a scaled-power split-torque transmission with two opposed face gears, two input pinions and two idlers.^[ref] Multiple meshes make the geometry useful for distributing and recombining load, but also make alignment and compatibility important.

A bench rotation check can test the tooth-count ratio. A gear contact marking test, dimensional inspection and load-sensitive measurements address different questions about the manufactured surfaces and their operation. Correct output speed alone does not establish an acceptable gear contact pattern, tooth stress or gear efficiency.

Gear base pitch is the spacing of successive involute tooth profiles referred to the gear base circle. For base diameter $d_b$, tooth count $N$, gear module $m$ and reference gear pressure angle $\alpha$,It also gives the spacing between successive corresponding tooth contacts measured along the gear line of action. The gear circular pitch uses the reference circle instead, giving $p=\pi m$ and $p_b=p\cos \alpha$.^[ref]

For $m=2\mathrm{mm}$ and $\alpha =20{}^{\circ }$, $p=6.2832\mathrm{mm}$ but $p_b\approx 5.9043\mathrm{mm}$. A second gear with the same module but $25{}^{\circ }$ reference angle has $p_b\approx 5.6945\mathrm{mm}$. Matching reference tooth spacing alone therefore does not make these the same specified mating geometry.

Changing the mounting separation of a compatible involute pair does not change its cut profiles, base circles or gear base pitch. In operating-circle notation, $p_w=2\pi r_w/N$ changes with mounted radius, whilestays fixed. This links the mounted operating pressure angle to an invariant tooth-profile spacing.

For a tooth rotating at angular speed $\omega$, base-circle tangential speed is $r_b|\omega |$. Dividing by gear base pitch gives the gear mesh frequency,A 30-tooth gear at $600$ revolutions per minute gives $f_m=300\mathrm{Hz}$. Finally, the gear contact ratio divides usable gear path of contact length by this base pitch, so profile spacing and available contact length jointly determine overlap between successive tooth engagements.

Gear circular pitch is the arc distance between corresponding points on successive gear teeth, measured on the gear reference circle. If that circle has diameter $d$ and tooth count $N$, its circumference contains $N$ repetitions, givingwhere $m$ is gear module. The length is measured along the reference arc, rather than as a straight chord between tooth positions.^[ref]

For a spur gear with $m=2\mathrm{mm}$ and $N=30$, reference diameter is $60\mathrm{mm}$, gear circular pitch is $2\pi \mathrm{mm}\approx 6.283\mathrm{mm}$, and angular tooth spacing is $2\pi /30$. The corresponding chord on the reference circle isThe small numerical difference matters when a dimensional inspection is intended to measure reference arc spacing. Increasing the tooth count while holding gear module fixed enlarges the gear reference circle but preserves gear circular pitch.

For an involute tooth profile, the gear base circle provides another spacing, the gear base pitch. Since $d_b=d\cos \alpha$, with reference gear pressure angle $\alpha$,At $\alpha =20{}^{\circ }$, the preceding example gives $p_b\approx 5.904\mathrm{mm}$. Compatible contact must preserve the spacing of successive tooth flanks along their gear line of action; this explains why equal gear circular pitch with incompatible gear pressure angles is not enough to specify a mating pair. Tooth thickness and backlash are additional quantities: gear circular pitch includes an entire tooth-and-space repetition.

The gear module specifies the size of metric gear teeth through the gear reference circle. For a spur gear with reference diameter $d$ and $N$ teeth,The tooth count is dimensionless, so gear module has units of length, conventionally millimetres. A larger gear module means a larger reference diameter at fixed tooth count. It does not mean a larger gear ratio, which depends on the tooth counts of the meshing pair.^[ref]

The gear circular pitch $p$ is the arc length between equivalent points on adjacent teeth, measured along the gear reference circle. Dividing the circumference by the tooth count givesFor example, a spur gear with $m=1.5\mathrm{mm}$ and $N=24$ has reference diameter $36\mathrm{mm}$ and gear circular pitch $1.5\pi \mathrm{mm}\approx 4.712\mathrm{mm}$. A 48-tooth gear of the same gear module has diameter $72\mathrm{mm}$ but the same tooth spacing. Their standard axis separation is $(36+72)/2=54\mathrm{mm}$, and their reduction gear ratio is $48/24=2$.

Conversely, two gears can have the same diameter without compatible tooth spacing: $d=36\mathrm{mm}$ can describe 24 teeth of gear module $1.5\mathrm{mm}$ or 18 teeth of gear module $2\mathrm{mm}$. Such teeth do not form the specified standard pair. For ordinary compatible spur gears, matching gear module is necessary but does not by itself specify the complete tooth geometry: the gear pressure angle and other tooth details must also agree. The definition uses reference diameter, not the diameter through the tooth tips or the operating pitch circle of a particular mounting.

A gear pitch circle is an imaginary circle used to represent the motion or reference geometry of a gear. A useful distinction is between the gear reference circle, specified for an individual gear, and the operating pitch circle, determined for a meshing pair. The terminology entry in KHK Gear Nomenclature calls the latter the intermeshing pitch circle and also uses the name working pitch circle.^[ref]

For an external pair with fixed axes and constant gear ratio, imagine two operating pitch circles in contact and rolling without slipping. If their radii are $r_1,r_2$ and their axis separation is $a$, their geometry and signed angular velocities obeyThe last equality follows by matching the gear ratio to tooth counts $N_1,N_2$. It is an ideal kinematic construction: the imaginary circles themselves are not physical rims carrying the contact force.

For standard unshifted straight-tooth gears at their standard axis separation, the gear reference circles coincide with the operating pitch circles. The gear module $m$ specifies reference diameter $d=mN$. With $m=2\mathrm{mm}$ and tooth counts 20 and 40, the reference diameters are $40\mathrm{mm}$ and $80\mathrm{mm}$, giving reference radii $20\mathrm{mm}$ and $40\mathrm{mm}$ and standard separation $60\mathrm{mm}$. The reference diameters differ from the larger tooth-tip diameters. If a compatible pair is operated at another axis separation, its gear reference circles remain properties of the individual gears, while its operating pitch circles must fit the new separation and the same tooth-count ratio. This is why an unspecified “pitch diameter” should not silently mix reference geometry with operating geometry.^[ref]

A gear reference circle is the imaginary circle used to specify an individual gear's tooth geometry. For a spur gear, its diameter $d$ is defined by gear module $m$ and tooth count $N$ through $d=mN$. It supplies a common datum for tooth spacing and other dimensions, whether or not that gear is currently meshing with another one. The operating pitch circle, in contrast, describes the mounted pair's motion.^[ref]

For a 30-tooth spur gear with gear module $2\mathrm{mm}$, the reference diameter is $60\mathrm{mm}$. Thus successive teeth repeat at an angular interval of $2\pi /30$ and a gear circular pitch of $2\pi \mathrm{mm}$ on that circle. In the standard full-depth, unshifted geometry specified by KHK, the tooth-tip diameter is $d_a=d+2m$, giving $64\mathrm{mm}$ in this example. Measuring the outside diameter and calling it the reference diameter would therefore produce the wrong gear module.^[ref]

The gear base circle is another distinct geometric datum. For a tooth profile constructed as the involute of a circle, the gear base circle generates the curved tooth flank, whereas the gear reference circle fixes its nominal sizing. Their diameters obey $d_b=d\cos \alpha$, with reference gear pressure angle $\alpha$. With $d=60\mathrm{mm}$ and $\alpha =20{}^{\circ }$, the base diameter is approximately $56.382\mathrm{mm}$. These three diameters—base, reference and tip—answer different questions about the same physical gear.^[ref]

The operating pitch circles of two meshing gears are the imaginary circles that reproduce their motion by rolling without slipping. They are properties of the working pair and its mounting, whereas a gear reference circle specifies one gear's nominal geometry. Working pitch circle and intermeshing pitch circle are alternative names.^[ref]

Consider an external pair of spur gears on fixed parallel axes, with axis separation $a$ and tooth counts $N_1,N_2$. Their operating radii $r_{w1},r_{w2}$ must satisfy both contact geometry and the tooth-count gear ratio:Solving givesThus the operating radii scale with the actual separation, while the gear ratio stays fixed by tooth counts. These are kinematic equations, conditional on the teeth actually maintaining compatible contact.

For an original example, choose gear module $m=2\mathrm{mm}$ and tooth counts 20 and 40. Reference radii are $20\mathrm{mm}$ and $40\mathrm{mm}$; their standard separation is $60\mathrm{mm}$. If a compatible mounting uses $a=61\mathrm{mm}$ instead, operating radii become $20.333\dots \mathrm{mm}$ and $40.666\dots \mathrm{mm}$. At input angular velocity $30rad/s$ the output has $-15rad/s$, and both operating tangential speed magnitudes are $0.61m/s$. Using the reference radii in that speed calculation would incorrectly give $0.60m/s$.

For tooth flanks formed as involutes, the fixed gear base circles permit constant-ratio motion over a range of separations. If their radii are $r_{b1},r_{b2}$, the common-normal geometry giveswhere ${\alpha }_w$ is the operating pressure angle. Increasing separation therefore increases that angle, while leaving each gear reference circle and gear base circle unchanged. This geometric possibility does not guarantee adequate tooth contact, clearance or strength at an arbitrary separation: the physical tooth extents and mounting must still be checked.^[ref]

A reverted gear train returns the output rotation axis to the input axis, usually through a two-stage compound gear train. The input and output gears can rotate independently on coaxial shafts, while the intermediate gears share another rotating body. Coaxial axes are a layout condition in addition to the desired gear ratio.

For standard unshifted spur gears, let gears1 and2 mesh in the first stage and gears3 and4 in the second, with2 and3 rigidly connected. The common intermediate-axis separation requiresIf both stages use the same gear module, this reduces to $N_1+N_2=N_3+N_4$. The reduction ratio independently satisfies $i=(N_2/N_1)(N_4/N_3)$. Both conditions must be satisfied; multiplying arbitrary stage ratios does not ensure a reverted layout.^[ref]

For an original design example, choose counts20,60,16 and64, with module $2\mathrm{mm}$ in both stages. Both sums are80, so both separations are $80\mathrm{mm}$. The reduction is $3\times 4=12$, taking an input of1440 revolutions per minute to an output of120. Two external meshes give the same input/output rotation direction.

The gears occupy different axial planes so that coaxial input and output do not require them to be one rigidly joined gear. A practical design still needs independent shaft support, compatible tooth geometry in each stage and adequate clearances. Operating with shifted tooth geometry or another mounting changes the applicable separation equations; the simple tooth-sum condition belongs to the stated standard-gear model.

A spur gear is a cylindrical gear with straight teeth parallel to its rotation axis. A conventional external pair transmits motion between parallel axes. Unlike the inclined teeth of a helical gear, the ideal straight-tooth geometry produces no axial thrust from the tooth-normal contact force; there are still tangential and separating loads that the mounting must carry.^[ref]

For compatible spur gears, reference diameter is $d=mN$, where $m$ is gear module and $N$ is tooth count. Standard reference axis separation is $(d_1+d_2)/2$. Two external spur gears have signed angular velocity relation ${\omega }_2/{\omega }_1=-N_1/N_2$: they rotate in opposite directions. Matching gear module alone is insufficient; tooth profiles and gear pressure angles must also be compatible.

For an original example, take gear module $3\mathrm{mm}$ and tooth counts 20 and 60. Reference diameters are $60\mathrm{mm}$ and $180\mathrm{mm}$, so standard axis separation is $120\mathrm{mm}$. Driving the smaller spur gear at $600$ revolutions per minute gives the larger one $200$ revolutions per minute in the opposite direction. In a steady ideal transmission, an input torque of $2\mathrm{N}\mathrm{m}$ becomes $6\mathrm{N}\mathrm{m}$ at the output. The corresponding input gear tangential force is $2/0.030\approx 66.7\mathrm{N}$; multiplying this same force by the output reference radius $0.090\mathrm{m}$ recovers the output torque.

A simple bench demonstration marks one tooth on each spur gear and counts complete turns, testing the three-to-one gear ratio. Measuring transmitted torques and rotational speeds additionally tests gear efficiency. Observing the rotation ratio alone cannot establish a tooth's allowable load or the losses caused by friction and backlash.