Gear tooth load fraction (${\eta }_j=F_j/F$)

The gear tooth load fraction ${\eta }_j$ is the fraction of a stated total mesh force carried by tooth pair $j$ at a particular contact position or time:For nonnegative forces resolved in the same direction, $0\le {\eta }_j\le 1$ and ${\sum }_j{\eta }_j=1$. A normal-force fraction must not mix one pair's normal load with another convention's tangential total. At zero total load the ratio is undefined.

An original quasistatic model treats engaged pairs as parallel springs with the same normal approach $\delta$. If $F_j=k_j\delta$ and every pair has zero initial gap, thenTwo pairs with stiffnesses $60$ and $140N/\mu \mathrm{m}$ under total load $1000\mathrm{N}$ approach by $5\mu \mathrm{m}$ and carry $300$ and $700\mathrm{N}$. Their fractions are $0.3$ and $0.7$, rather than one half each. Counting two geometrically overlapping contacts does not establish equal gear tooth load sharing.

An initial gap $e_j$ changes the model toA pair below its gear tooth engagement threshold carries no load in this unilateral model. Changing total load can change both the active pairs and their fractions, even if all the individual stiffnesses remain constant. Gear contact ratio specifies geometric overlap; load fractions require deformation and engagement information.

The fractions also prevent double counting. If total load is $1000\mathrm{N}$, assigning that full load to both of two pairs gives an impossible sum of $2000\mathrm{N}$ within this model. A gear friction work per engagement calculation must use each pair's own $F_j(t)$ before summing its dissipation.

Dynamic motion can alter the quasistatic distribution. A 1986 NASA analysis calculated tooth stiffness and loads as contact position and speed varied, using a coupled stiffness/load iteration.^[ref] Fractions inferred from the simple spring model should therefore be identified as model results, rather than universal operating values.

A gear tooth engagement threshold is the relative approach or total load at which a previously separated tooth pair starts carrying compressive contact force in a stated model. Geometric overlap from the gear contact ratio does not guarantee that every potentially overlapping pair already carries load. Gaps, errors and deformation affect the gear mesh active-contact set.

For an original unilateral linear-spring model, writewith $k_j>0$, common approach $\delta$ and initial gap $e_j$. Pair $m$ begins to carry load as $\delta$ rises above $e_m$. The corresponding total-load threshold isThis threshold includes the forces already carried by earlier contacts. It is not generally obtained by multiplying pair $m$'s own stiffness by its gap.

Take $k_1=80$, $k_2=120N/\mu \mathrm{m}$, $e_1=0$ and $e_2=3\mu \mathrm{m}$. The second pair begins at total load $80\cdot 3=240\mathrm{N}$. At $200\mathrm{N}$, approach is $2.5\mu \mathrm{m}$ and the second pair remains unloaded. At $600\mathrm{N}$,gives $\delta =4.8\mu \mathrm{m}$, forces $384$ and $216\mathrm{N}$, and gear tooth load fractions $0.64$ and $0.36$.

At the ideal threshold itself, the new contact contributes zero force but changes the one-sided gear mesh tangent stiffness. The force is continuous while its slope can jump. Finite contact geometry and nonlinear local Hertzian contact can smooth or alter this elementary linear-spring picture.

A controlled quasistatic test can increase total mesh load at approximately fixed contact position while measuring relative displacement and individual tooth-root strain. A change in response slope suggests a contact transition, but support motion and measurement resolution must be considered before assigning it uniquely to a tooth pair. Primary dynamic gear analysis couples tooth stiffness and calculated loads as contact position changes, underscoring that engagement cannot be inferred from tooth count alone.^[ref]

The gear mesh active-contact set identifies the tooth pairs that carry positive compressive normal force in a specified contact model. It is not simply the set of geometrically overlapping teeth from the gear contact ratio. A pair touching at zero force is excluded under the positive-force convention used here.

For unilateral linear contacts,Here $e_j$ is the initial gap, $k_j>0$ the pair stiffness, and $\delta$ the common approach. For a proposed nonempty set $\mathcal{A}$, force balance givesA gear contact-set consistency check then verifies $\delta >e_j$ for included pairs and $\delta \le e_j$ for excluded ones. Solving the linear equation without this check can retain a negative force or omit a contact that should engage.

An original three-pair example uses stiffnesses $100,50,150N/\mu \mathrm{m}$ and gaps $0,2,5\mu \mathrm{m}$. At total load $500\mathrm{N}$, the set $\{1,2\}$ gives approach $(500+50\cdot 2)/150=4\mu \mathrm{m}$ and forces $400,100,0\mathrm{N}$. This set is consistent.

At $900\mathrm{N}$, keeping only those two contacts would give approach $1000/150\simeq 6.667\mu \mathrm{m}$, beyond the third gap. Including all three instead givesand forces approximately $583.33,191.67,125\mathrm{N}$, which sum to $900\mathrm{N}$. The third gear tooth engagement threshold occurs at total load $100\cdot 5+50(5-2)=650\mathrm{N}$.

Within a fixed active set, gear mesh tangent stiffness is the sum of its pair stiffnesses. At a transition, force can remain continuous while that derivative changes. For positive total load the scalar force law is strictly increasing after the first contact, giving a unique approach in this model; the unloaded state need not specify one unique separation.

Real deformation, local contact nonlinearity and dynamics can require more than one common-approach coordinate. A primary NASA analysis coupled tooth stiffness with dynamic-load calculations over contact position and speed.^[ref] The active-set calculation is an explicit quasistatic model, not a substitute for that fuller mechanical description.

A gear contact-set consistency check verifies that a proposed solution satisfies force balance and the unilateral contact conditions used to define a gear mesh active-contact set. Solving an equation for selected contacts is insufficient if an omitted tooth should be loaded or an included tooth would require tension.

For the model $F_j=k_j\max (\delta -e_j,0)$, choose a trial active set $\mathcal{A}$ and solveThe check then requires positive $k_j(\delta -e_j)$ for included pairs and $\delta \le e_j$ for excluded pairs. Recomputing every contact with the unilateral law gives the force residualA consistent exact solution has $r_F=0$ together with the inclusion inequalities.

An original example has stiffnesses $100,50,150N/\mu \mathrm{m}$ and gaps $0,2,5\mu \mathrm{m}$. At $F_{\mathrm{applied}}=900\mathrm{N}$, a trial set containing only the first two pairs gives $\delta =20/3\mu \mathrm{m}$. It balances those selected forces but exceeds the third gap by $5/3\mu \mathrm{m}$. The omitted contact would carry $250\mathrm{N}$, giving $r_F=250\mathrm{N}$. Including all three gives the consistent approach $35/6\mu \mathrm{m}$.

Conversely, including all three at applied load $500\mathrm{N}$ gives the un-clipped solution $\delta =4.5\mu \mathrm{m}$ and a third force $-75\mathrm{N}$. Rejecting that tensile contact and solving with the first two gives $\delta =4\mu \mathrm{m}$ and forces $400,100,0\mathrm{N}$.

Numerical tolerances should keep their units and roles clear. A displacement tolerance near a gear tooth engagement threshold is not the same quantity as a force-residual tolerance. At an exact zero-force touch, either a geometric-touch flag or the positive-force active convention may be useful, but the reported convention must be stated. The one-sided gear mesh tangent stiffness can differ across that boundary.

Primary dynamic gear analysis couples tooth stiffness and calculated loads as contact position changes.^[ref] The scalar check above validates internal consistency of its quasistatic model; it does not establish that the model includes every deformation or dynamic effect in a real mesh.