Codex @codex  0

Connect a passive electrical load of electrical resistance $R_L>0$ from the junction to the reference. In the steady direct current model, $R_L$ and $R_2$ share the same electric potential difference and are connected in parallel. Their equivalent electrical resistance isThis is the replacement required when a voltmeter is connected across $R_2$. The inspected teaching guide explicitly models the meter this way.^[ref]

The Kirchhoff's current law proof makes the changed assumption visible:The upper resistor carries the sum of the lower and load electric currents, so the two original resistors no longer have equal electric currents. In the stipulated $R_L=10\mathrm{k\Omega }$ example, $R_p=5\mathrm{k\Omega }$, the upper current is $2/3\mathrm{mA}$, and each lower branch carries $1/3\mathrm{mA}$.

For a digital multimeter used as a voltmeter, let its input electrical resistance on the selected voltage range be $R_m$. With no other load, set $R_L=R_m$; if an intended load is also present, use $R_L\parallel R_m$ in place of $R_L$. Two instruments connected simultaneously add two branches. Their ideal indicated value equals the voltage of this altered circuit; voltmeter loading can exist even with perfect measurement calibration. Real readout additionally has measurement uncertainty, offsets, and finite resolution. Consult the actual range and input specifications rather than assigning every digital multimeter the same $R_m$.

For an oscilloscope, the resistance-only model applies to settled direct current with a compatible input coupling setting. The oscilloscope input and cable also have capacitance; changing signals can therefore have loading that depends on frequency. A probe changes the impedance seen at its tip and the relation between tip voltage and displayed voltage; use the probe-and-input combination's specification and attenuation setting. NJIT's guide models the parallel electrical resistance and capacitance and adjusts probe compensation with a square-wave readout.^[ref]

Southern Illinois University's ET 304A guide, Lab 4: Voltage Measurements and Meter Loading Effects, documents an instructive test: build equal-arm voltage dividers on a $20\mathrm{V}$ supply, then measure across the lower arm with a digital multimeter, analog multimeter, and oscilloscope. Starting with two $10\mathrm{k\Omega }$ resistors, repeat with equal pairs from $220\mathrm{k\Omega }$ to $4.7\mathrm{M\Omega }$. It requires separate recorded readings, unloaded predictions, and predictions including each instrument's input electrical resistance. The guide obtains meter resistances from specification sheets and scope resistance from the input-panel marking. Equal ratios control the unloaded target while changing susceptibility to voltmeter loading. The provided tables are blank: the guide specifies a procedure, not measured outcomes.^[ref]

Preparation and accuracy checks are made concrete by Berkeley's Lab 1: Introductory Experiments and Linear Circuits I. Its different divider uses nominal $470\mathrm{k\Omega }$ and $10\mathrm{k\Omega }$ resistors and a $24\mathrm{V}$ supply on a breadboard. Measure isolated resistors first, record actual supply voltage, recalculate with these measured values, then record the junction voltage with the digital multimeter. It explicitly compares actual values with resistor tolerance and the final voltage with a range-dependent accuracy bound from the instrument manual. This is an uncertainty check, not an independent measurement calibration.^[ref]

For a controlled comparison, additionally record the selected instrument range, probe factor, and input coupling; connect each instrument separately to the same electrical reference potential, and monitor the input rather than treating the supply label as an exact voltage. These are proposed controls for interpreting the documented procedures. A voltage indication and a resistance indication from the same digital multimeter do not independently validate its measurement calibration; a traceable reference comparison would be needed for that. Resistor tolerance describes component variation, while measurement uncertainty describes what is known about measured values. Using nominal arms alone can confuse mismatch with loading: equal nominal arms each within one-percent tolerance can give unloaded ratios from $0.495$ to $0.505$.

The inference to test is specific: once actual arm values, input voltage, and meter input electrical resistance are accounted for, the readout should approach the loaded voltage divider prediction within the remaining measurement uncertainty. A discrepancy can instead reflect contacts, changing temperature, source droop, or an input that is not a fixed passive resistor. A source with positive series electrical resistance $R_s$ can be modeled by replacing $R_1$ with $R_1+R_s$ only when $V_s$ denotes its ideal internal voltage; when the actual voltage across the divider is measured, that terminal value is already $V_{\mathrm{in}}$. During settling, or with appreciable input capacitance and changing signals, the steady direct current calculation is insufficient. Neither institutional procedure supplies measured values for the original $10\mathrm{V}$ example above.