Boundary-density calibration for erosion fronts determines the local density needed to convert a surface mass-loss rate into a polymer erosion front speed. The relevant density is that of the material crossing the boundary, conditioned consistently with the mass and dimensional measurements. Whole-specimen mass divided by whole-specimen volume gives an average, not automatically the required boundary value.
For a spherical, inward-moving boundary of radius , negligible interior density change givesThe local-density requirement follows from nonuniform-density erosion inference. NIST defines mass density as mass divided by volume; the experimental volume and sampled region must therefore be specified.[ref]
An original calibration construction removes or samples a shell of thickness . Its mean density isA finite shell measures a weighted layer average. For a smooth radial profile, expansion gives . Thus a thinner shell approaches the boundary value, but finite-layer bias depends on the density gradient. Finite-shell bias in boundary-density calibration is distinct from random weighing error.
For the stipulated profile at current radius , a shell with giveswhereas the actual boundary density is . Substituting the shell average into the instantaneous speed conversion overestimates speed by about 4.9%. These are original profile calculations, not measured material properties.
Very thin layers have their own uncertainty cost. For measured layer mass and volume , first-order propagation givesShrinking the layer can increase relative mass and thickness uncertainty. Shared dimensional corrections can correlate volumes and successive layer estimates; the GUM requires relevant covariance terms.[ref] A smaller sampling thickness therefore trades spatial averaging against measurement uncertainty.
A proposed experiment uses matched specimens or recorded sequential sectioning, measures removed material and layer geometry, and compares several layer thicknesses. Distinguish wet, dried, porous-envelope and solid-material volumes. Cutting, drying or extracting a layer can change its composition, so independent spatial observations should test whether the sampled material represents the original boundary.
Kureha's polyglycolic acid degradation test filters and dries residual solids after water exposure.[ref] It supplies retained dry mass; it does not supply local boundary density or prove the existence of a sharp erosion front. The additional calibration construction above makes those missing measurements explicit.
Grain (unit) Created 2026-10-31 Updated 2026-11-05
A grain (unit) is a unit of mass equal to exactly , or . Thus a recorded mass of ten grains converts to . The abbreviation is ; it must be distinguished from , the symbol for a gram.[ref]
NIST Guide to the SI. Appendix B.8, entries grain (gr) to kilogram and milligram; exact conversion factors
A grain (unit) measures mass, whereas a minim measures volume. Converting a volume to a mass additionally requires the material's density, so these units cannot be substituted for one another. The exact conversion is useful when interpreting an older measurement without treating the mass of an individual seed as a physical standard.
Heterodyne amplitude-versus-power gain conversion translates a calibration of measured electric power into a calibration of beat-current amplitude. In a fixed resistive load, power is quadratic in current amplitude, so a multiplicative power correction becomes a square-root amplitude correction. The electrical reference plane and peak-versus-root mean square convention must also agree.
For sinusoidal load current and resistance ,For two measurements of the same load, . A power multiplier of four therefore means an amplitude multiplier of two. In decibels, the same change is dB. NIST distinguishes the factor ten for power ratios from the factor twenty for field-amplitude ratios when their quadratic relationship applies.[ref]
If the load resistance also changes, the more general relation isFor frequency-dependent complex impedances, use the appropriate circuit and power model rather than replacing resistance by an arbitrary complex number. A measured electric potential difference likewise requires its stated impedance before it can be converted to current.
For a corrected detector-current peak amplitude , the normalized overlap is . If the numerator is instead detector-current RMS amplitude, the denominator is . Using an RMS numerator with the peak denominator lowers the result by , a 3.0103 dB discrepancy under the amplitude-ratio convention. The mistake is a convention mismatch, not evidence of worse optical overlap.
Current-plane convention in heterodyne calibration is another independent issue. In an ideal matched Norton circuit, a source peak current splits equally between source resistance and equal load resistance . Load peak current is , so delivered power is , rather than . The factor depends on the specified equivalent circuit; real detector capacitance and interconnecting networks require their measured response.
NIST's two-laser receiver apparatus measures microwave power and separately corrects sensor calibration, network loss and impedance mismatch. Its matched optical modes make the modulation calculable, while the electrical corrections locate the power at the intended reference plane.[ref]
Frequency response metrology for high-speed optical receivers by Paul D. Hale and others. PDF pp. 1–2, Heterodyne measurements, Eqs. 1–4 and Fig. 1
Record raw power, correction factors, reference plane, load, amplitude convention and DC-current calibration separately. Only then apply the gain-matching condition for heterodyne normalization. Nonuniform-density erosion inference 2026-11-05
Nonuniform-density erosion inference estimates a polymer erosion front speed when local density varies through a specimen. Total mass divided by total volume gives an average density; the material being removed at the boundary can have a different density. Substituting the average into a surface-removal formula can therefore misestimate the speed.
For an original spherically symmetric model, let be the surviving radius and the local mass density. ThenDifferentiating the integral and defining positive inward speed givesThis radial form of the Reynolds transport theorem separates loss at a moving boundary from density change inside the surviving volume. All quantities must refer to the same material and conditioning state; a water-filled wet volume and a subsequently dried polymer mass do not automatically define the local density used here.
If the interior density profile is stationary in spatial coordinates over the measurement interval, the integral term vanishes. The appropriate boundary conversion is then , with . Writing average density as , a uniform-density substitution instead givesThe ratio is measurable information about the profile, not a shape correction already supplied by knowing the outer radius.
An illustrative fixed profile is , with a fixed initial radius, not the changing current radius. At , the boundary density is and the mean is . The uniform-density inference overestimates the instantaneous front speed by 25%. For cm, and true , mass leaves at ; dividing by the mean-density surface factor gives . These are stipulated profile values, not measured properties of a named polymer.
Time-dependent hydration, porosity or chemical change can make the interior integral nonzero. One mass slope cannot independently identify both that contribution and boundary speed. Boundary-density calibration for erosion fronts therefore needs spatial or compositional evidence in addition to a bulk mass measurement. NIST's mass-density definition is mass divided by volume; it does not equate a whole-specimen average with an unknown boundary value.[ref]
A discriminating experiment measures outer dimensions, conditioned mass and density or composition at several depths, using matched specimens or accounting for destructive sampling. Kureha's polyglycolic acid protocol filters and dries the remaining solids after water exposure.[ref] That observation supplies retained dry mass, not a radial density field. Establish an inward-moving degradation boundary before interpreting the inferred speed as polymer erosion, rather than another cause of material loss.
The 1864 solid units are the avoirdupois pound, avoirdupois ounce and grain; the liquid units are the Imperial measures. The grain is unchanged, while the old apothecaries' pound and ounce are not the units of the new formulary. [ref]
The Prescriber's Analysis of the British Pharmacopoeia by John Birkbeck Nevins (1864). pp. 16–17, change of weights and unchanged liquid measures
- one grain: , about ;
- one avoirdupois ounce: ;
- one avoirdupois pound: .
- one minim: ;
- one fluid drachm: ;
- one fluid ounce: ;
- one Imperial pint: ;
- one Imperial gallon: .
A millilitre is a cubic centimetre, and a litre is a cubic decimetre. These displayed equivalents are rounded; small differences from a period table's last digits reflect rounding and historical calibration conventions. A fluid ounce is a volume and an avoirdupois ounce is a mass. They cannot be interchanged for an arbitrary liquid without its density. Likewise, a drop is not a defined minim: its volume depends on the liquid and the dropper.
[ref]
NIST Guide to the SI. Appendix B.8, grain, avoirdupois pound and ounce, Imperial gallon and fluid measures; modern rounded metric conversions
Physical quantity Created 2026-10-13 Updated 2026-11-05
A physical quantity is a property of a phenomenon, body or substance whose magnitude can be expressed by a number and a reference, usually a unit of measurement. For example, the length and the same length have different numerical values but represent the same physical quantity. The numerical value alone is therefore incomplete.
A physical quantity must also be specified physically. A gas's pressure at a stated position and temperature, the mass of a specimen, and a detector's electric current are different measurands even if an instrument happens to display the same number for them. Dimensional analysis constrains which quantities can be added or compared, while a system of units supplies a consistent convention for expressing them.[ref]
Standard gravity 2026-11-05
Standard gravity is the conventional reference accelerationexactly. It supplies a fixed reference for unit conversions and for expressing an acceleration as a multiple of . It is distinct from the locally measured gravitational acceleration, which depends on location and height.[ref]
NIST Guide to the SI. Appendix B.9, Acceleration: standard acceleration of free fall; bold conversion factors are exact
For example, . If a vertical force on a mass of is calculated using this reference, . The same calculation using a measured local value gives instead. The reference value's exactness does not remove measurement uncertainty from a real force or from the actual local gravitational field.
One can measure local gravitational acceleration by tracking a body in free fall with an optical interferometer, taking positive downward and fitting its vertical position to after instrumental corrections. Such an experiment estimates at the apparatus; it does not determine the already stipulated number .[ref]
Gravity laboratory by Istituto Nazionale di Ricerca Metrologica. Laboratory description, interferometric vertical-trajectory measurement and environmental corrections
System of units Created 2026-10-13 Updated 2026-11-05
A system of units chooses reference units of measurement for a set of base physical quantities and specifies how other units of measurement are derived. In the International System of Units, length, mass and time are expressed using the metre, kilogram and second; a velocity has derived unit .
A consistent system allows an equation to connect numerical values without hidden unit-conversion factors. It does not change the underlying physical relation: the same speed may be written as or . The familiar formulas for electromagnetism can nevertheless contain different constants in SI and Gaussian conventions, because the definitions of the electrical quantities differ as well as their numerical scales.[ref]
Unit of mass Created 2026-10-31 Updated 2026-11-05
A unit of mass is a reference for expressing mass. The SI base unit is the kilogram; the gram is . A unit of mass differs from a unit of force: a balance may infer mass from a gravitational force, but a newton measures force and is not another name for a kilogram.
In a weighing experiment the relation connects the two, with local gravitational acceleration . An instrument calibrated to display mass therefore incorporates a reference or an assumed local . Moving a force-sensing instrument to a different gravitational environment can change that inference even though the specimen's mass is unchanged.[ref]
Unit of volume Created 2026-10-31 Updated 2026-11-05
A unit of volume is a reference for expressing a three-dimensional volume. In the International System of Units its coherent form is the cubic metre, . A litre is and a millilitre is .
Length conversions must be cubed: because , one cubic centimetre equals , rather than . This accounting matters when a measured mass and volume determine a mass density, or when a number density is converted between laboratory and SI conventions.[ref]