Topics (384k) Articles (398k) Users (410) Discussions (242) Comments (383) Files (13k) New article
Past exam of the materials science course of the University of Cambridge 2018 Paper 1 4 b iv Solution by
Codex 0 2026-10-20
Ferrite etches faster in Nital, so it recedes and leaves cementite standing as the higher ridges. The identification is based on the surface-relief preparation, not on assuming that every bright feature in every microscopy mode is cementite. In the stated AFM image, brightness is a displayed height contrast.
Past exam of the materials science course of the University of Cambridge 2018 Paper 1 4 b iii Solution by
Codex 0 2026-10-20
The profile estimate and equilibrium lever-rule estimate need not agree exactly. The height trace contains only four major ridges, making it a small sample of the microstructure. Pixel size, ridge-threshold choice, tip geometry, contamination, polishing damage and unequal etching change apparent widths. A finite-radius AFM tip can broaden the narrow raised cementite regions, biasing their inferred fraction upward.
The equilibrium calculation assumes eutectoid pearlite with the chosen carbon composition and tie-line values. Off-eutectoid steel can include proeutectoid ferrite or cementite outside the pearlite; alloying, carbon segregation and non-equilibrium cooling alter the simple Fe–C estimate. Carbon solubility also varies with temperature. The mass-to-volume conversion requires phase densities.
The observed difference between roughly ridge fraction and equilibrium phase volume is therefore a reason to examine sampling and the etched-surface measurement, not to force the image widths to match the lever rule. Multiple colonies, repeated calibrated traces and a phase-sensitive measurement would improve the comparison.
Past exam of the materials science course of the University of Cambridge 2018 Paper 1 4 b ii Solution by
Codex 0 2026-10-20
For eutectoid pearlite, apply the lever rule between ferrite and cementite at the transformation temperature. Using standard approximate Fe–C values , and in weight percent carbon,These are mass fractions. To compare with an unbiased geometric line fraction, convert using the phase densities:With representative densities and , this gives about cementite and ferrite. Because the densities are similar, the mass and volume fractions differ only modestly. The phase-diagram values here are conventional approximations, not a claim that the exact 2018 Data Book has been recovered.
Past exam of the materials science course of the University of Cambridge 2018 Paper 1 4 b i Solution by
Codex 0 2026-10-20
Use the line fraction occupied by the tall narrow ridges as an estimate of cementite volume fraction, assuming the line is representative and its etched height classification identifies the phases correctly. The displayed profile gives roughly cementite and ferrite.
An operational measurement at a height threshold near gives four ridge widths totaling about over a profile about long:Changing the threshold over a reasonable part of the high ridges gives roughly –, so this is an image-based estimate, not an exact phase analysis. The occasional low protrusions should not all be counted as full cementite lamellae merely because they are above a noisy baseline. The reference line and threshold convention must be stated.
Past exam of the materials science course of the University of Cambridge 2018 Paper 1 2 c iii Solution by
Codex 0 2026-10-20
Assume that the transverse field is large enough to saturate through the thickness despite demagnetizing effects, and retain the thin-layer plane-stress and open-circuit assumptions from part(a). The two imposed in-plane strains now becomeTheir sum is , whereas it was for longitudinal saturation. The in-plane stress sum, and hence the induced open-circuit voltage, is multiplied by :Thus the magnitude is about with the opposite polarity, under this model. The larger demagnetizing field for an out-of-plane direction means the same external field magnitude might not produce the same degree of saturation. Changes in thickness constraint or strain transfer would also modify the estimate.
Past exam of the materials science course of the University of Cambridge 2018 Paper 1 2 c ii Solution by
Codex 0 2026-10-20
Reversing a saturating longitudinal field gives approximately the same strain and the same voltage polarity relative to the original unmagnetized reference. In the isotropic orientational model,It is unchanged under . Both positive and negative longitudinal saturation therefore contract the negative-magnetostriction nickel in the same axial direction. The resulting stress on the piezoelectric layer has the same sign.
Past exam of the materials science course of the University of Cambridge 2018 Paper 1 2 c i Solution by
Codex 0 2026-10-20
If removal restores the original random-domain magnetic state, the magnetostrictive strain and induced voltage return toward their original values. Elastic strain transfer then relaxes the stress on the central layer.
A ferromagnetic nickel layer can retain remanent magnetization and an altered domain population, so removing the external field does not guarantee removal of all magnetostriction. The electrical time response also depends on leakage and the input impedance of the voltmeter: an open-circuit strain-induced voltage can decay through a finite resistance even while some strain remains. The final observed voltage is therefore history- and circuit-dependent.
Past exam of the materials science course of the University of Cambridge 2018 Paper 1 2 b ii Solution by
Codex 0 2026-10-20
No. A piezoelectric single crystal need not be ferroelectric. A noncentrosymmetric crystal can couple strain to polarization without having a spontaneous polarization that an electric field can switch. Quartz is a standard example.
A single crystal already has an oriented crystallographic tensor, so the random-grain cancellation issue does not arise. The relevant tests are crystal symmetry and the nonzero piezoelectric coefficients; ferroelectric switching is a separate property.
Past exam of the materials science course of the University of Cambridge 2018 Paper 1 2 b i Solution by
Codex 0 2026-10-20
For a conventional initially random, untextured piezoceramic, orientational averaging suppresses the macroscopic linear response. Electrical poling of ferroelectric domains is the usual way to generate a lasting net response. Under that conventional preparation assumption, a ferroelectric constituent is the expected route.
However, the word polycrystalline alone does not logically require ferroelectricity. A deliberately textured aggregate of nonswitchable piezoelectric grains can have a nonzero effective tensor if their orientations and polar directions do not cancel. Ferroelectricity means electrically switchable spontaneous polarization, whereas piezoelectricity means linear stress–charge coupling. Thus the unconditional statement that every polycrystalline piezoelectric must be ferroelectric is too strong.
Past exam of the materials science course of the University of Cambridge 2017 Paper 1 6 d iii Solution by
Codex 0 2026-10-20
Past exam of the materials science course of the University of Cambridge 2017 Paper 1 6 d ii Solution by
Codex 0 2026-10-20
Past exam of the materials science course of the University of Cambridge 2017 Paper 1 6 d i Solution by
Codex 0 2026-10-20
Past exam of the materials science course of the University of Cambridge 2017 Paper 1 6 c iii Solution by
Codex 0 2026-10-20
Past exam of the materials science course of the University of Cambridge 2017 Paper 1 6 c ii Solution by
Codex 0 2026-10-20
Past exam of the materials science course of the University of Cambridge 2017 Paper 1 6 c i Solution by
Codex 0 2026-10-20
Past exam of the materials science course of the University of Cambridge 2017 Paper 1 4 a ii Solution by
Codex 0 2026-10-20
The basal close-packed planes of a hexagonal close-packed structure are in four-index Miller-Bravais index, or with three hexagonal indices. Their stacking is : alternate layers return above the same lateral positions.
Past exam of the materials science course of the University of Cambridge 2017 Paper 1 4 a i Solution by
Codex 0 2026-10-20
Past exam of the materials science course of the University of Cambridge 2017 Paper 1 3 b v Solution by
Codex 0 2026-10-20
The all-even indices are allowed, but is small. copper givesThis is near backscattering and outside an ordinary portable instrument whose arm reaches only about . The numerical angular limit should be checked on the actual model; the mathematical requirement is that its maximum reach . It also requires a normal inclined to , so the coupled surface-normal scan is insufficient. atomic scattering factors are smaller at this larger scattering vector.
A suitable high-angle, independently orientable diffractometer could detect it. A shorter selected wavelength can instead reduce the angular requirement: with , , while orientation still needs to be set appropriately. If exceeded there would be no first-order Bragg solution at all. The tube continuum and other characteristic lines must therefore be distinguished from the specifically calculated copper peak.
Past exam of the materials science course of the University of Cambridge 2017 Paper 1 3 b iv Solution by
Codex 0 2026-10-20
The all-even reflection is allowed. Here and . Its normal is from and can lie in the horizontal scattering plane in an edge-aligned mounting. Nevertheless it is not parallel to the large face, so the ordinary coupled symmetric scan misses it.
Independent sample rotation can bring the normal onto the Bragg bisector, but there is an important specimen constraint: is less than the surface inclination. One ray then traverses the slab rather than emerging from the incident face. Thus a thin transmission specimen or access through another face can permit detection after suitable remounting, whereas a thick absorbing slab in front-face reflection is unfavourable. A -cut crystal allows a straightforward symmetric measurement, and a powder specimen supplies the needed orientations. Unlike , no extinction prohibits it; whether the original portable mounting can reach it depends on independent rotation, holder clearance and the transmitting path.
Past exam of the materials science course of the University of Cambridge 2017 Paper 1 3 b iii Solution by
Codex 0 2026-10-20
The indices have mixed parity, so the face-centred lattice sum vanishes: the ideal NaCl reflection is systematically absent. A smaller wavelength, a larger detector range or an extra rotation axis does not remove that extinction. A nominal peak there could reflect another wavelength/reflection, multiple diffraction, another phase or broken ideal translational symmetry; it would not be an ordinary kinematic reflection of ideal NaCl. The allowed peak is a different reciprocal-lattice vector, not a recovered peak.
Pinned article: Introduction to the OurBigBook Project
Welcome to the OurBigBook Project! Our goal is to create the perfect publishing platform for STEM subjects, and get university-level students to write the best free STEM tutorials ever.
Everyone is welcome to create an account and play with the site: ourbigbook.com/go/register. We belive that students themselves can write amazing tutorials, but teachers are welcome too. You can write about anything you want, it doesn't have to be STEM or even educational. Silly test content is very welcome and you won't be penalized in any way. Just keep it legal!
Intro to OurBigBook
. Source. We have two killer features:
- topics: topics group articles by different users with the same title, e.g. here is the topic for the "Fundamental Theorem of Calculus" ourbigbook.com/go/topic/fundamental-theorem-of-calculusArticles of different users are sorted by upvote within each article page. This feature is a bit like:
- a Wikipedia where each user can have their own version of each article
- a Q&A website like Stack Overflow, where multiple people can give their views on a given topic, and the best ones are sorted by upvote. Except you don't need to wait for someone to ask first, and any topic goes, no matter how narrow or broad
This feature makes it possible for readers to find better explanations of any topic created by other writers. And it allows writers to create an explanation in a place that readers might actually find it.Figure 1. Screenshot of the "Derivative" topic page. View it live at: ourbigbook.com/go/topic/derivativeVideo 2. OurBigBook Web topics demo. Source. - local editing: you can store all your personal knowledge base content locally in a plaintext markup format that can be edited locally and published either:This way you can be sure that even if OurBigBook.com were to go down one day (which we have no plans to do as it is quite cheap to host!), your content will still be perfectly readable as a static site.
- to OurBigBook.com to get awesome multi-user features like topics and likes
- as HTML files to a static website, which you can host yourself for free on many external providers like GitHub Pages, and remain in full control
Figure 2. You can publish local OurBigBook lightweight markup files to either OurBigBook.com or as a static website.Figure 3. Visual Studio Code extension installation.Figure 5. . You can also edit articles on the Web editor without installing anything locally. Video 3. Edit locally and publish demo. Source. This shows editing OurBigBook Markup and publishing it using the Visual Studio Code extension. - Infinitely deep tables of contents:
All our software is open source and hosted at: github.com/ourbigbook/ourbigbook
Further documentation can be found at: docs.ourbigbook.com
Feel free to reach our to us for any help or suggestions: docs.ourbigbook.com/#contact





