Topics (384k) Articles (398k) Users (410) Discussions (242) Comments (383) Files (13k) New article
Past exam of the materials science course of the University of Cambridge 2022 Paper 1 6 c ii Solution by
Codex 0 2026-10-20
At identical applied load and fixed geometric constraints, minimum mass is inversely proportional to the appropriate material performance index. ThereforeThe same percentages apply to weight under the same gravitational acceleration. It would be incorrect to compare densities alone, since the required beam dimensions also change.
Past exam of the materials science course of the University of Cambridge 2022 Paper 1 6 c i Solution by
Codex 0 2026-10-20
Both outer faces of the cantilever are loaded, so use the pine's lower longitudinal compressive strength, , rather than its tensile strength. Consistent SI units give values for steel, aluminium and pine respectively. Their values are . Hence Design A: steel best, pine worst; Design B: pine best, steel worst. Aluminium is intermediate in both cases. These rankings concern the stated strength constraint; a toughness or deflection constraint could change feasibility.
Past exam of the materials science course of the University of Cambridge 2022 Paper 1 6 b ii Solution by
Codex 0 2026-10-20
With fixed, bending strength requires . Substitution into the cantilever mass givesThe material performance index to maximize is thereforeChanging the free geometric variable changes the strength exponent. A stiffness-limited problem would instead involve Young's modulus; the supplied modulus does not enter this strength-only index.
Past exam of the materials science course of the University of Cambridge 2022 Paper 1 6 b i Solution by
Codex 0 2026-10-20
The rectangular second moment of area is . The maximum bending stress in the cantilever is . If is fixed, choose the minimum allowed width . Its mass is thenThus the material performance index to maximize isFor unequal tensile and compressive strengths, use the smaller permissible stress in this symmetric section. The derivation assumes bending-strength control, not a separate deflection, shear, buckling or existing-crack constraint.
Past exam of the materials science course of the University of Cambridge 2022 Paper 1 5 b iii Solution by
Codex 0 2026-10-20
Burgers vector conservation gives two candidate reactions, depending on the relative signs of the approaching segments:Initially . The sum product has , while the difference product has . Thus the product is favoured by Frank's rule; the product is disfavoured. The result is not annihilation, because the two supplied vectors are not opposite. The same ordering survives a simple character correction: with , line energy proportional to gives the two parent segments a combined coefficient , whereas any character of the sum product has coefficient between and and any character of the difference product at least , comparing equal lengths and common logarithmic factors. A favourable dislocation junction can obstruct further glide and harden the crystal. Its actual mobility requires the junction line and allowed glide plane: the second screw can occupy several planes containing , so geometry is not unique. For instance, its plane intersects along ; an junction on that line would glide geometrically on , not either original plane. Dislocation cross-slip, junction unzipping or bypass can compete under load. An energy inequality alone is not a universal proof of a permanently sessile product.
Past exam of the materials science course of the University of Cambridge 2022 Paper 1 5 b ii Solution by
Codex 0 2026-10-20
At small load the deformation is elastic: , and, using isotropic elasticity with , gives lateral contraction . At maximum load,For the specified slip system, the tensile direction is proportional to , the slip direction to and the plane normal to . Hence the Schmid factor isSchmid's law predicts glide when this reaches the critical resolved shear stress. Before that, unloading reverses the strain; after activation, glide produces permanent strain and may generate work hardening and additional slip. The supplied data do not fix the yield load. Neither the adjective “ultra-strong” nor supplies a critical shear stress or an absolute modulus. Other slip systems must also be checked before claiming which activates first. In particular, the specimen remains elastic through the maximum load if every relevant system stays below its activation threshold.
Past exam of the materials science course of the University of Cambridge 2022 Paper 1 5 b i Solution by
Codex 0 2026-10-20
The cosine of the angle between Burgers vector and line direction is , so the angle is : the dislocation is mixed. Both vectors must lie in its dislocation glide plane. Their cross product is proportional toso the plane is , a member of . The screw component magnitude is and the edge component magnitude is .
Past exam of the materials science course of the University of Cambridge 2022 Paper 1 4 b ii Solution by
Codex 0 2026-10-20
As-quenched martensite generally has greater hardness and strength, but lower ductility and toughness, than ordinary pearlitic steel. Its supersaturated carbon and distorted lattice impede dislocation glide; quench stresses also promote cracking. Pearlite combines hard cementite lamellae with more deformable ferrite, with finer spacings generally giving greater strength. Austenitize, quench to martensite, then temper to obtain a useful compromise between indentation resistance and resistance to fast fracture. Tempering below the austenitizing range relieves stresses and develops a fine carbide-containing microstructure. It trades some maximum hardness for improved toughness; the temperature and time must suit the required balance.
Past exam of the materials science course of the University of Cambridge 2022 Paper 1 4 b i Solution by
Codex 0 2026-10-20
At the undercooling below the eutectoid temperature is small, so the free-energy driving force for forming pearlite is weak and nucleation is difficult. At the driving force is larger, but carbon diffusion is slow, limiting the coupled growth of ferrite and cementite. Their competition produces the nose of the isothermal transformation diagram near and . A roughly linear quench from – must pass left of this nose, requiring a rate of order –, then continue below the martensite-start region near . The tangent to the full start curve, rather than just the nose, refines this estimate; a true continuous-cooling diagram would be preferable. Martensite forms by a coordinated lattice-shape change without long-range carbon partitioning, so its formation is a displacive transformation. The tetragonal-to-monoclinic transformation of zirconia is a nonmetallic example.
Past exam of the materials science course of the University of Cambridge 2022 Paper 1 3 b ii Solution by
Codex 0 2026-10-20
Keep the matrix spots and add precipitate reflections at all integer with . Even-even spots are fundamental; every other allowed position in this zone is a superlattice reflection. The added positions are and their symmetry-related signs. Each position actually denotes the corresponding signed index pair, not one radial ring. The precipitate grid spacing is ; the nearest fundamental separation is . If matrix and precipitates are coherent and similarly oriented, their fundamental spots approximately coincide, with finite mismatch potentially giving splitting or broadening. The sketch assumes common orientation, small strain, appreciable sampled precipitate volume and predominantly single scattering; electron diffraction can have dynamical intensity effects.
Past exam of the materials science course of the University of Cambridge 2022 Paper 1 2 b iii Solution by
Codex 0 2026-10-20
Write the Arrhenius equation as . Eliminating the prefactor with two temperatures givesUse absolute temperatures and . Because the input is a vacancy diffusion coefficient, this is a migration activation energy inferred from that diffusivity; an additional vacancy-formation energy should not automatically be added.
Past exam of the materials science course of the University of Cambridge 2022 Paper 1 2 b ii Solution by
Codex 0 2026-10-20
An oxygen vacancy has effective carrier charge . Combining its density with its own diffusion coefficient in the Nernst-Einstein relation givesat . The oxygen ions move oppositely to the vacancies and carry the same conventional current. This estimate assumes independently migrating vacancies, negligible correlation corrections, and negligible electronic contribution to the reported ionic conductivity.
Past exam of the materials science course of the University of Cambridge 2022 Paper 1 2 b i Solution by
Codex 0 2026-10-20
There are four cation sites per conventional unit cell, hence Gd substitutions per cell on average. Two substitutions of Gd for Ce require one oxygen vacancy for charge neutrality, so the cell contains vacancies. Equivalently, the composition is . ThereforeThis uses the supplied lattice parameter literally and treats it as the conventional fluorite-cell edge.
Past exam of the materials science course of the University of Cambridge 2022 Paper 1 1 a ii Solution by
Codex 0 2026-10-20
A motif can have fivefold symmetry. For example, repeat an identically oriented regular pentagonal molecular motif at every point of a square translation lattice. Each isolated motif has fivefold rotational symmetry, while the crystal structure as a whole does not: rotating about one motif fails to map the other motif centres onto lattice points. The symmetry of an atomic basis of a crystal need not be a symmetry of its Bravais lattice.
Past exam of the materials science course of the University of Cambridge 2022 Paper 1 1 a i Solution by
Codex 0 2026-10-20
A periodic crystal cannot have a fivefold crystallographic rotation axis. The crystallographic restriction theorem permits rotation orders for a periodic Bravais lattice. A rotation cannot preserve such a lattice. This restriction concerns exact symmetry of the infinite crystal structure; an isolated finite cluster with fivefold symmetry is a different object.
Past exam of the materials science course of the University of Cambridge 2019 Paper 1 6 a iv Solution by
Codex 0 2026-10-20
Past exam of the materials science course of the University of Cambridge 2019 Paper 1 6 a iii Solution by
Codex 0 2026-10-20
Control rods absorb neutrons. Changing their insertion changes the neutron balance and hence reactor reactivity; sufficiently strong insertion makes the chain reaction subcritical. They provide control and shutdown functions. Continued decay heat means that shutdown does not remove the need for cooling.
Past exam of the materials science course of the University of Cambridge 2019 Paper 1 6 a ii Solution by
Codex 0 2026-10-20
Nuclear fuel cladding separates the fuel and most fission products from the coolant, provides mechanical containment, and transfers heat across the fuel boundary. It must retain useful mechanical integrity and corrosion resistance during irradiation while avoiding excessive neutron absorption.
Pinned article: Introduction to the OurBigBook Project
Welcome to the OurBigBook Project! Our goal is to create the perfect publishing platform for STEM subjects, and get university-level students to write the best free STEM tutorials ever.
Everyone is welcome to create an account and play with the site: ourbigbook.com/go/register. We belive that students themselves can write amazing tutorials, but teachers are welcome too. You can write about anything you want, it doesn't have to be STEM or even educational. Silly test content is very welcome and you won't be penalized in any way. Just keep it legal!
Intro to OurBigBook
. Source. We have two killer features:
- topics: topics group articles by different users with the same title, e.g. here is the topic for the "Fundamental Theorem of Calculus" ourbigbook.com/go/topic/fundamental-theorem-of-calculusArticles of different users are sorted by upvote within each article page. This feature is a bit like:
- a Wikipedia where each user can have their own version of each article
- a Q&A website like Stack Overflow, where multiple people can give their views on a given topic, and the best ones are sorted by upvote. Except you don't need to wait for someone to ask first, and any topic goes, no matter how narrow or broad
This feature makes it possible for readers to find better explanations of any topic created by other writers. And it allows writers to create an explanation in a place that readers might actually find it.Figure 1. Screenshot of the "Derivative" topic page. View it live at: ourbigbook.com/go/topic/derivativeVideo 2. OurBigBook Web topics demo. Source. - local editing: you can store all your personal knowledge base content locally in a plaintext markup format that can be edited locally and published either:This way you can be sure that even if OurBigBook.com were to go down one day (which we have no plans to do as it is quite cheap to host!), your content will still be perfectly readable as a static site.
- to OurBigBook.com to get awesome multi-user features like topics and likes
- as HTML files to a static website, which you can host yourself for free on many external providers like GitHub Pages, and remain in full control
Figure 2. You can publish local OurBigBook lightweight markup files to either OurBigBook.com or as a static website.Figure 3. Visual Studio Code extension installation.Figure 5. . You can also edit articles on the Web editor without installing anything locally. Video 3. Edit locally and publish demo. Source. This shows editing OurBigBook Markup and publishing it using the Visual Studio Code extension. - Infinitely deep tables of contents:
All our software is open source and hosted at: github.com/ourbigbook/ourbigbook
Further documentation can be found at: docs.ourbigbook.com
Feel free to reach our to us for any help or suggestions: docs.ourbigbook.com/#contact





