Blast furnace Created 2026-10-31 Updated 2026-11-05
A blast furnace is a shaft furnace in which a descending solid charge encounters rising hot gases. In iron extraction, the charge includes iron ore, coke and a flux such as limestone. The products include molten pig iron and slag, which separates from the metallic liquid.[ref]
The gases supply both heat and a reducing environment. A simplified iron oxide reduction is
Here carbon monoxide removes oxygen from the iron oxide and becomes carbon dioxide. The opposing flows allow rising gases to heat and react with incoming material before leaving the furnace: countercurrent flow helps recover energy within the process. The pig iron contains substantial carbon and requires further refining for most steelmaking.
Countercurrent flow 2026-11-05
Countercurrent flow is an arrangement in which two interacting streams move in opposite directions. In a heat exchanger, a hot stream can transfer heat to a cold stream along the exchanger's length. Each location must have a suitable local temperature difference, although the cold outlet can be warmer than the hot outlet because those outlets are at opposite ends.
For example, with equal constant heat-capacity flow rates and negligible losses, a hot stream cooling from to can heat the opposing stream from to . The end temperature differences are both , and the two energy balances agree. A blast furnace similarly uses opposing solid and gas flows to exchange heat and reactants efficiently.
Iron extraction 2026-10-31
Conversion of an iron-bearing ore into metallic iron, for example by carbon monoxide reduction in a blast furnace.
Steel is an iron-based alloy with controlled carbon content and impurities; its manufacture requires extracting iron from an ore and then adjusting the composition. In a modern plain-carbon classification, steel generally contains less than about carbon by mass, whereas pig iron is more carbon-rich. The historical practical contrast was with low-carbon wrought iron and readily cast but relatively brittle cast iron. Hardening by quenching is characteristic of suitable carbon-rich steels, but not every grade hardens in the same way.
Begin, for example, with an iron oxide ore. Preparation removes some earthy matter and, where appropriate, roasting expels moisture or converts a carbonate-bearing ore to oxide. A blast furnace receives the ore, coke and a flux such as limestone. The hot air blast sustains combustion of coke, generating heat and the carbon monoxide needed for much of the oxide reduction. Representative overall balances are
Calcination of limestone provides calcium oxide. Combination with acidic gangue, represented by silica, gives a liquid slag:
Actual slag is a multicomponent melt, rather than necessarily pure calcium silicate. The descending iron picks up carbon and other impurities and collects as molten pig iron. This first extraction product is not already finished steel.
Two important routes available in 1867 proceed from this stage. In the older indirect route, refining and puddling oxidize much of the carbon and remove slag-associated impurities to obtain wrought iron. Bars packed with charcoal are then heated for a prolonged period in the cementation process. Carbon enters the bars, giving blister steel; forging and welding can make shear steel, while melting suitable stock in covered crucibles produces more uniform crucible steel. The bar can acquire carbon through gas-mediated surface reactions and diffusion; the process should not be imagined as intact charcoal grains travelling through the iron.
In the Bessemer process, an air blast passes through molten pig iron in a converter. Oxidation of silicon, manganese and carbon supplies heat, while lowering the carbon content. Composition can be corrected by adding a controlled carbon- and manganese-bearing material such as spiegeleisen. Henry Bessemer's 1856 patent describes the central idea of maintaining the conversion by oxidizing constituents of the molten metal, without fuel for reheating during that stage.[ref]
The early acidic converter demanded suitable feed: it did not solve removal of phosphorus from every ore. Later basic converter practice must not be silently imported into a December 1867 account. Final casting, working and heat treatment determine the steel microstructure and properties as well as composition. The useful manufacturing chain is therefore ore → extracted carbon-rich iron → controlled composition → worked and appropriately heat-treated steel.
Pig iron Created 2026-10-31 Updated 2026-11-05
The carbon-rich first molten iron product of traditional blast furnace smelting, also containing other feed-dependent impurities.
Steelmaking Created 2026-10-31 Updated 2026-11-05
Steelmaking produces steel by controlling the carbon content, other alloying elements and unwanted constituents of iron. A blast furnace first produces carbon-rich pig iron; a basic oxygen furnace then refines the molten material by oxidation and composition adjustment. An electric arc furnace instead supplies heat electrically to melt a charge that can include recycled steel, direct reduced iron and pig iron.[ref]
The distinction between iron extraction and steelmaking matters: converting an iron oxide to metallic iron and adjusting an existing iron-based alloy to the required composition are different tasks. The Bessemer process is an important historical example of refining pig iron by an air blast; modern basic oxygen steelmaking uses an oxygen supply rather than ordinary air.