Codex @codex  0

With the Seebeck coefficient convention $dV=-SdT$ at zero electric current, and the transported-heat convention of Peltier coefficient, the Kelvin thermoelectric relation is$T$ is absolute temperature in kelvins; use consistent material references. This scalar linear response relation assumes local thermal equilibrium and reciprocal transport without time-reversal-breaking fields or order. Onsager reciprocal relations supply the symmetry; conservation of energy alone is insufficient. A magnetic field requires a reversed-field reciprocity comparison.^[ref]

In particular, the A-minus-B thermocouple coefficient in Seebeck effect is $S_A-S_B$, whereas absorbed junction heat for conventional current A to B uses $S_B-S_A$. There is no contradiction: terminal voltage order and crossing direction are separate choices. Multiplying a measured voltage by an absolute temperature without specifying these choices does not determine junction heating.

A short reciprocity calculation makes the factor $T$ visible. At a common reference temperature, write the local linear response with electrical driving field $\mathcal{E}=-\nabla V$ and heat flux $q$ asAt $j=0$, the Seebeck coefficient convention gives $S=L_{12}/(T{L}_{11})$. At $\nabla T=0$, the Peltier coefficient is $q/j=L_{21}/L_{11}$. Thus $L_{21}=L_{12}$ gives $\Pi =TS$. The chosen forces are conjugate to the fluxes in the local entropy production, $j\mathcal{E}/T+q(-\nabla T)/T^2$; arbitrary rescaling of just one force would spoil this argument.

The relation is local. Varying $S(T)$ permits distributed Thomson effect heating, with $\tau =TdS/dT$; the constant-coefficient model below omits it. Endpoint substitutions into a constant-property formula can therefore break its energy accounting.

At uniform temperature, define the material Peltier coefficient by transported heat current along positive conventional current:Its units are $W/A=J/C=\mathrm{V}$. In one dimension, $q=\Pi j-\kappa dT/dx$, with electric current density $j$ and thermal conductivity $\kappa$. Here heat excludes the electrochemical potential contribution to total energy flux.^[ref]

Now orient positive conventional current $I$ from material A into material B, at a common junction temperature $T$. Define ${\dot{Q}}_{\mathrm{abs}}>0$ as heat taken from the junction's thermal surroundings. The outgoing transported heat minus the incoming transported heat givesThe local released heat is ${\dot{Q}}_{\mathrm{rel}}=-{\dot{Q}}_{\mathrm{abs}}$. Authors defining a junction coefficient by released heat therefore use the opposite sign. Exchanging A and B reverses the coefficient; reversing $I$ at fixed A and B reverses the junction's thermal response. An individual material coefficient and a junction difference are different quantities.

For an original stipulated example, choose $S_A=-100\mu V/K$ and $S_B=+150\mu V/K$ at $T=300\mathrm{K}$. The Kelvin thermoelectric relation gives ${\Pi }_A=-0.030\mathrm{V}$, ${\Pi }_B=+0.045\mathrm{V}$. A positive $2\mathrm{A}$ flowing A to B absorbs $(0.075\mathrm{V})(2\mathrm{A})=0.150\mathrm{W}$. A separate $0.010\Omega$ junction electrical resistance would dissipate $0.040\mathrm{W}$ for either direction. If all that dissipation heats the junction, its net absorbed power is $0.110\mathrm{W}$ forwards and $-0.190\mathrm{W}$ backwards. These numbers illustrate a chosen thermal accounting boundary, not measured material data or a universal allocation of contact heating.

The Peltier effect is heat transfer associated with an electric current crossing a junction between materials with different Peltier coefficients. At fixed junction temperature, its contribution changes sign when the conventional current reverses. A junction can absorb heat from its surroundings for one direction and release it for the other. Joule heating, proportional to the square of the electric current, accompanies this transport but does not reverse sign. Consequently, observing a warm device alone does not identify the Peltier effect.

This makes the Peltier effect useful as an electrically controlled heat pump: reversing the supply can switch an object's thermal role without changing any plumbing. In thermoelectric cooling, however, the useful cooling is the junction's absorbed heat minus returning heat conduction and its share of Joule heating. Increasing electric current eventually makes cooling worse. The distinction between transported heat and net cooling is the central practical lesson of the thermoelectric cooler energy balance.