At , the daily component is multiplied by and has a lag of ten radians. The annual component instead has . HenceThe sketch is nearly a smooth annual sinusoid, with annual amplitude about and annual phase lag about radians, corresponding to about days on the chosen year scale. The tiny daily component is retained in the formula rather than declared identically zero.
At the surface both attenuation factors are one and both lags vanish:The sketch is a rapid daily oscillation on a slowly varying annual background. The amplitudes cannot be inferred uniquely from the sampling intervals alone.
The adequately sampled record shows a yearly cycle and a daily cycle. Up to exchanging their labels,Using days per year for numerical estimates,These are angular frequencies. The corresponding ordinary frequencies are and .
The source text and its figure are inconsistent here. The plotted low-frequency maximum in W is near , rather than the printed . The original PDF shows that this discrepancy is already present in the examination, rather than introduced by transcription.
Machine 2 records only about half a year. Its first nonzero discrete Fourier transform bin is therefore atThe annual component near is below that first bin. The finite window function spreads it through spectral leakage, with a prominent first-bin contribution. This explains the plotted peak without invoking a new physical period.
The true daily component has , above machine 3's Nyquist frequency. At sampling times days,The last sequence is also produced by a continuous cosine with frequency sampled at those same times. Hence the observed peak is the sampled sinusoid aliasIt is not evidence for an additional two-day physical temperature cycle.
The conventional Nyquist frequency isFrequencies above this cutoff are indistinguishable from lower-frequency sampled sinusoid aliases. The Nyquist–Shannon sampling theorem requires a band limit strictly below the cutoff for general phase information: at exactly the cutoff, some phases can give zero samples. Thus hours is the conventional limiting period, with unambiguous reconstruction requiring a longer period under those sampling assumptions.
The consistent matching is:
Series C stops after about six months, identifying machine 2. Its short record gives spectrum W a coarser Fourier frequency resolution. Series A resolves the annual variation but misses the changing daily phase: the regular three-day interval samples the daily oscillation at the same phase, so its daily contribution aliases to a constant. Its spectrum is Y. Machine 3 produces the half-daily-frequency alias in X, leaving D as its time series. The fully sampled two-year record B and spectrum Z agree with the supplied first row.
These identifications use the record lengths, frequency locations and sampling intervals. They do not require assuming that the plotted spectral heights have an identical normalization.
The shorter, stronger northern pulses and broader southern pulses suggest propagation from south to north, towards the northern station. The useful evidence is the difference in pulse widths, not just the earlier northern arrivals: the latter chiefly reflect station distance.
As rupture reaches successively more northerly patches, each patch radiates a new P wave and S wave pulse. Towards the north, the later emission time is partly cancelled by a shorter propagation path; those contributions arrive closer together. Towards the south, later emission and a longer path add, stretching the signal. This is rupture directivity. It refers to the advance of the slipping region along the fault, not necessarily the direction of the local fault slip vector. A thrust can slip up-dip while its rupture front advances in a direction with a northward component.
More generally, emission from a patch at distance along the rupture arrives atThe forward direction has a smaller arrival-time spread. This is the same travel-time compression captured by isochrone-based rupture directivity calculations.[ref]
A formulation of directivity for earthquake sources using isochrone theory. The primary report relates directivity to rupture geometry, seismic speed and the arrival-time distribution of radiation from successive fault patches.
Larger northern amplitude supports the interpretation but is not decisive on its own because geometrical spreading, seismic attenuation, seismic radiation patterns and site response also affect amplitude. With only two traces, propagation, filtering and site effects remain alternatives to test; the idealized exercise is most naturally explained by northward directivity.For a unilateral finite-source rupture advancing at approximately constant rupture velocity , the along-fault propagation length isThere is no supplied or calibrated seismic source time function, so a unique spatial extent cannot be read directly from Figure 4. For illustration, and an assumed would give . Allowing – and assumed – gives lengths of order 8–15 km. These are explicitly conditional scale estimates, not measured fault dimensions.
If equal-and-opposite ray geometry and phase pulse durations were known, the directivity model in solution would instead constrain a projected length,where is the angle between the rupture direction and the northern ray. Distinct P and S wave speeds, unknown takeoff angles, smooth pulse boundaries and the clipped southern S tail prevent a reliable independent numerical inversion here. This observation is consistent with a few-kilometre projected extent while the actual along-fault length can be larger. A rupture length is not the accumulated fault slip, the width of the whole fault plane, or the approximately 50 km station distance.
Distinguish the duration of one phase pulse from the P-to-S separation. Figure 4 shows northern pulses with most visible motion over roughly 3–4 s each, compared with roughly 4–5 s or more in the south. Reading the low-amplitude tails gives approximately 11.5–15.2 s for the northern P pulse, 17.7–20.9 s for the northern S pulse, 14.2–19.0 s for the southern P pulse, and 22.3 s to beyond the right plot boundary near 27 s for the southern S pulse. Thus the latter duration is censored by the plotting window; it should not be assigned an exact ending at 27 s. The positive-to-negative extremum separations are only about 1 s in the northern pulses, 1.3 s in the southern P pulse and 1.4 s in the southern S pulse; those much shorter numbers are not full source durations. Smooth tails have no unique onset or ending at the precision of this drawing.
A finite-source rupture has an intrinsic duration that differs from the apparent pulse duration through rupture directivity. In an ideal unilateral line-source model, neglecting local slip rise time, instrument filtering and path broadening,Here is the chosen phase wave speed and is the rupture's projection along equal-and-opposite takeoff directions. Averaging corresponding full pulses in that model suggests an intrinsic timescale of roughly 4–5 s. This is an order-of-magnitude graph estimate, not an exact rupture duration; the figure does not supply a seismic source time function definition, receiver responses, phase deconvolution, or geometry sufficient to determine one uniquely. A finite local slip rise time would also contribute to the observed width.
Use the northern S–P time, approximately , rather than multiplying an absolute-clock arrival by a wave speed. For common approximately straight paths,No numerical crustal velocities are specified in Q3. If the usual illustrative crustal values and are adopted, the distance isThese assumed crustal speeds are unrelated to Q1's offshore layer values. They are representative rather than measurements of the Swiss column; the British Geological Survey gives broad typical crustal ranges of 5–7 km/s for P waves and 3–4 km/s for S waves.[ref]
How are earthquakes detected by British Geological Survey. The seismic-wave table provides typical crustal speed ranges, not a velocity model for this particular earthquake.
Using the corresponding northern central pulse times gives an effective source time near after midnight, and the S estimate is the same to graph accuracy. The southern central landmarks similarly give a distance near 70 km and an effective source time near 5 s. That consistency supports the example, but pulse landmarks need not mark the rupture's true onset. is a source-to-station path or hypocentral distance in the uniform-speed approximation. An epicentral distance additionally needs the hypocenter depth; it cannot simply be equated to 50 km for an unknown depth.
The northern station is closer, under comparable P wave and S wave paths through the same velocity model. In the actual Figure 4 the northern P and S pulses are separated by about 6 s, whereas the southern separation is roughly 8–8.5 s. The S–P time removes the unknown earthquake origin time:Both northern pulses also occur earlier on the shared absolute clock, consistent with the smaller distance. Earlier arrival alone would not be sufficient if clocks or velocity models differed.
For reproducible graph readings, the northern positive-to-negative zero crossings are approximately for P and for S; the southern crossings are approximately and . These are convenient corresponding pulse landmarks, not sharply defined first-break onsets. The first visible motion begins earlier: approximately 12 s and 18 s in the north, and 14–15 s and 22–23 s in the south, depending on the amplitude threshold. The horizontal axis is seconds since midnight on 1 January 2000, not elapsed time since rupture initiation.
For the chlorite–kaolinite reaction, take water and both solids to have unit thermodynamic activity. Its reaction quotient is . ThereforeThis line has a shallower negative slope than the chlorite–gibbsite line, with points and . Plot both against predominantly negative , because the dissolved silica thermodynamic activity is generally below one.
Use decimal logarithms and write and . The question's concentration notation is interpreted as dimensionless thermodynamic activities, or concentrations divided by a fixed standard concentration with activity coefficients set to one.
There are unlisted articles, also show them or only show them.