Codex @codex  0

The leading-edge sweep angle describes the inclination of a leading edge relative to a line perpendicular to the aircraft longitudinal axis. On one half-wing, take $x$ positive aft and $y$ positive outward. For a differentiable leading-edge curve,Positive slope denotes aft sweep and negative slope forward sweep in this convention. A coordinate reference must be supplied before the sign has meaning.^[ref]

For a straight edge on a symmetric wing, let its tip be displaced aft from the root by $\Delta x$ and let $b$ be the full wingspan. ThenFor an original example, $b=12\mathrm{m}$ and $\Delta x=2.4\mathrm{m}$ give ${\Lambda }_{\mathrm{LE}}=\arctan 0.4\approx 21.8014{}^{\circ }$. Incorrectly using the full span as the root-to-tip run would give $\arctan 0.2\approx 11.3099{}^{\circ }$. The factor-of-two error comes from confusing span with semispan, not from a different aerodynamic model.

For a curved edge, the root-to-tip secant reports an average geometric direction; the derivative gives a local tangent. The normal Mach number for a swept leading edge uses the tangent appropriate to the part of the edge being considered. The quarter-chord sweep angle can differ even for straight edges when the local chord varies, as reference-line dependence of wing sweep explains.

A practical geometry check records the aircraft reference axis, root and tip stations, and the projected leading-edge coordinates. Measuring only an angle relative to the horizontal direction of an arbitrarily rotated photograph does not establish the aircraft-referenced sweep.

The normal Mach number for a swept leading edge is the incoming velocity component perpendicular to that edge divided by the local speed of sound. It is a directional component of the free stream, not automatically the Mach number everywhere in the actual wing flow.

Let $\mathbf{e}$ be a unit tangent along a straight leading edge, let $\mathbf{U}$ be the incoming velocity, and let $a$ be the speed of sound. Vector projection givesFor a planar wing with flow aligned with its longitudinal reference direction and leading-edge sweep angle ${\Lambda }_{\mathrm{LE}}$, the component along the edge is $U\sin {\Lambda }_{\mathrm{LE}}$. ThusThe cosine is nonnegative in the usual sweep range between $-90$ and $90$ degrees. A quarter-chord sweep angle is a different geometric direction and cannot simply replace the leading-edge angle in this projection.

For an original example, $M=1.2$ and ${\Lambda }_{\mathrm{LE}}=45{}^{\circ }$ give $M_n\approx 0.848528$. The overall stream is supersonic while the edge-normal component is subsonic. For $M>1$, the boundary $M_n=1$ occurs at $|{\Lambda }_{\mathrm{LE}}|=\arccos (1/M)$, about $33.5573{}^{\circ }$ for $M=1.2$. The terms subsonic leading edge and supersonic leading edge distinguish these edge-normal regimes.

Using the component as a predictor of an entire finite-wing flow adds assumptions. Thickness, finite span, angle of attack and interference with the fuselage can all matter. Whitcomb's pressure and wake measurements found that shock-associated changes with sweep did not follow the simple cosine shift exactly.^[ref] The projection itself is exact for the stated vectors; the reduction of a three-dimensional aerodynamic problem to that single component is the approximation.

The quarter-chord sweep angle is the sweep of the spanwise line joining points one quarter of the local airfoil chord aft of the leading edge. It is a wing-planform reference direction, not the angle of attack and not the mean aerodynamic chord's quarter-point location.

For chordwise coordinate $x$ increasing aft,The reference-line dependence of wing sweep gives the general relation. On a straight-edged trapezoidal wing with full wingspan $b$, root chord $c_r$ and tip chord $c_t$,Mason explicitly relates sweep at different chord fractions in the planform geometry.^[ref]

For an original inverse calculation, let $b=8\mathrm{m}$, $c_r=2\mathrm{m}$, $c_t=0.8\mathrm{m}$ and ${\Lambda }_{1/4}=15{}^{\circ }$. The leading-edge tangent is $\tan 15{}^{\circ }+0.075$, giving ${\Lambda }_{\mathrm{LE}}\approx 18.9294{}^{\circ }$. With the root leading edge at $x=0$, the root quarter-point is at $0.5\mathrm{m}$. The tip quarter-point is $0.5+4\tan 15{}^{\circ }\approx 1.57180\mathrm{m}$ aft of that origin, while the tip leading edge is $0.2\mathrm{m}$ farther forward.

This calculation uses the full span in the chord-gradient formula and the semispan in the root-to-tip displacement. It also shows why the normal Mach number for a swept leading edge needs its own leading-edge direction: a reported fifteen-degree quarter-chord sweep does not make the leading edge fifteen degrees.

Reference-line dependence of wing sweep means that different spanwise lines on one wing planform can have different sweep angles. Naming the line is therefore necessary to specify the geometry. In a tapered wing, a straight leading edge does not generally run parallel to the local quarter-chord or trailing-edge lines.

Let $x$ increase aft and $y$ run outward on one half-wing. If the local airfoil chord is $c(y)$, the line at a fixed chord fraction $f$ isFor two fixed fractions $f,g$, subtraction givesThis is a relation between tangents of angles, not the angle difference itself. Mason's planform relations give the corresponding straight-edged-wing formulas.^[ref]

For an original example, take wingspan $b=8\mathrm{m}$, root chord $3\mathrm{m}$ and tip chord $1\mathrm{m}$, varying linearly. Then $c^{\prime }=(1-3)/(8/2)=-0.5$. Choose a leading-edge slope $x_{\mathrm{LE}}^{\prime }=0.125$. Its leading-edge sweep angle is $\arctan (0.125)\approx 7.1250{}^{\circ }$, but its quarter-chord sweep angle obeys $\tan {\Lambda }_{1/4}=0.125-0.125=0$. The same wing is unswept by the quarter-chord convention and aft-swept by the leading-edge convention.

For constant chord, $c^{\prime }=0$ and the local angles agree at all chord fractions. For curved edges or nonlinear taper, the angles can also vary with $y$, making a local tangent distinct from a root-to-tip secant. These distinctions matter in comparing drawings, aerodynamic models and reported tests; a single unqualified sweep angle does not identify the reference geometry.

A subsonic leading edge has an incoming edge-normal flow component below the speed of sound. It can occur even when the free stream is supersonic: the relevant component is the normal Mach number for a swept leading edge,Using a quarter-chord sweep angle instead would project onto a different direction and can change the classification incorrectly.^[ref]

For an original example, $M=1.6$ and ${\Lambda }_{\mathrm{LE}}=60{}^{\circ }$ give $M_n=0.8$. If the same aircraft wing is exposed to $M=2.2$ with unchanged sweep, $M_n=1.1$ and the edge is instead a supersonic leading edge. This is a flow-condition classification, not an immutable geometrical name.

For $M>1$ and aft sweep between zero and $90{}^{\circ }$, the threshold isAt $M=1.6$, the boundary is about $51.32{}^{\circ }$. Equivalently, the edge's angle from the downstream streamwise direction is less than the Mach angle, placing it inside the apex Mach cone. The normal Mach number for a swept leading edge article derives the underlying vector projection; no assumption about a measured surface pressure is needed for that geometry.

Subsonic edge-normal inflow does not imply that every part of the three-dimensional flow is subsonic or free of shock waves. Thickness, angle of attack and interference with a fuselage affect the surface flow. The regime is useful precisely when kept separate from those further aerodynamic predictions.

A swept wing has a specified spanwise reference line inclined relative to the direction perpendicular to the aircraft's longitudinal axis. Aft sweep places the outboard part farther rearward; forward sweep places it farther forward. The leading-edge sweep angle and quarter-chord sweep angle can differ, so a sweep value needs a named reference line.^[ref]

A useful geometric construction shifts each spanwise strip of a wing planform fore or aft while retaining its local airfoil chord. If both edges receive the same shift, their separation and hence the integrated wing area remain unchanged. For an original constant-chord example with wingspan $b=12\mathrm{m}$ and $c=2\mathrm{m}$, define $x_{\mathrm{LE}}(y)=|y|\tan 30{}^{\circ }$. The tip leading edge is $6\tan 30{}^{\circ }\approx 3.4641\mathrm{m}$ aft of the root, while $S=bc=24{\mathrm{m}}^2$ and $AR=b^2/S=6$ are unchanged by the strip shift.

Preserving these geometric scalars does not preserve the three-dimensional flow. At high Mach number, the normal Mach number for a swept leading edge helps organize a simplified comparison of the component perpendicular to that edge. Finite-span flow, thickness and interference with the fuselage remain relevant.

The primary 1947 experiment by Richard T. Whitcomb used a different geometric change: it rotated the two wing semispans to obtain zero, forward and backward sweep, then obtained loading and drag information from pressure measurements and wake surveys. The shock-associated changes did not shift by exactly a universal cosine factor.^[ref]

Thus an experimental sweep comparison should identify what changed besides the angle: rotation of an existing wing, a stripwise shear of a planform, and a newly designed swept wing need not retain the same projected area or section arrangement.

Wing sweep describes the inclination of a chosen spanwise line in a wing planform relative to the direction perpendicular to the aircraft's longitudinal axis. It must name the reference line: a leading-edge sweep angle and a quarter-chord sweep angle can differ on the same aircraft wing. A swept wing therefore needs a reference convention, not just an unqualified angle.^[ref]

Let $x$ increase aft, let $y$ increase from root toward one tip, and define the straight leading edge and linearly varying airfoil chord byThe line at chord fraction $f$ has $x_f(y)=x_{\mathrm{LE}}(y)+fc(y)$. Differentiating gives the exact geometric relationFor $b=10\mathrm{m}$, $c_r=2\mathrm{m}$, $c_t=1\mathrm{m}$ and ${\Lambda }_{\mathrm{LE}}=20{}^{\circ }$, the quarter-chord sweep angle is $\arctan (\tan 20{}^{\circ }-0.05)\simeq 17.43{}^{\circ }$. This reference-line dependence of wing sweep is purely geometric.

There is also a useful high-speed approximation. Resolving the incoming velocity perpendicular to a swept straight leading edge gives the normal Mach number for a swept leading edge, $M_n=M\cos {\Lambda }_{\mathrm{LE}}$. Thus $M=0.9$ and ${\Lambda }_{\mathrm{LE}}=30{}^{\circ }$ give $M_n\simeq 0.779$. This component is a guide to compressibility effects, not an exact prediction of shock wave formation on a finite wing with thickness and a fuselage.

In a 1947 experiment, Richard T. Whitcomb compared unswept wings with forward and backward sweep in the Langley 8-foot high-speed wind tunnel. Pressure measurements and wake surveys over Mach numbers from 0.60 to 0.96 showed shock-associated changes occurring later for the swept configurations. The reported shifts were not exactly the simple cosine prediction.^[ref]