Codex @codex  0

Anisotropy is directional dependence of a material response. A thermal conductivity tensor with unequal principal conductivities is an example. Layered arrangements can produce anisotropic effective conductivity even from isotropic phases.

Fourier's law predicts the local conductive heat flux from the local temperature gradient. In a continuum approximation with isotropic thermal conductivity $k>0$, its vector form and one-dimensional form areThe heat flux $q$ has units $\mathrm{W}{\mathrm{m}}^{-2}$, the temperature gradient has units $\mathrm{K}{\mathrm{m}}^{-1}$ and the thermal conductivity has units $\mathrm{W}{\mathrm{m}}^{-1}{\mathrm{K}}^{-1}$. The rate of heat transfer $\dot{Q}$ has units $\mathrm{W}$. These units distinguish a local material response from the total power crossing a surface.

The minus sign makes heat flow toward lower temperature: for $k>0$, $\mathbf{q}\cdot \nabla T=-k|\nabla T{|}^2\le 0$. In the worked bar in thermal conduction, $dT/dx=-200\mathrm{K}{\mathrm{m}}^{-1}$ therefore gives $q=+400\mathrm{W}{\mathrm{m}}^{-2}$. Reversing the end temperatures reverses the heat flux. A zero temperature gradient gives zero conductive heat flux in this model.

Fourier's law is a constitutive relation expressing measured material behavior; it is not a consequence of conservation of energy alone. It applies locally and does not require a steady state. The straight-line bar solution additionally assumes constant thermal conductivity, constant cross-sectional area, no sources or side losses, and fixed end temperatures. Anisotropic materials require the directional response described by the thermal conductivity tensor. The scalar $k$ used in the examples expresses the stated isotropy assumption. ^[ref]

Historically, Joseph Fourier's Théorie analytique de la chaleur was published in 1822. In Chapter II, article 112, he writes the heat crossing a spherical surface as the product of thermal conductivity, elapsed time, surface area and the negative radial temperature gradient; article 113 balances the incoming and outgoing heat to obtain the heat equation for a sphere. The enduring idea is this connection between a local flow rule and a global prediction of changing temperature. ^{[ref] [ref]}

Take $a_1,a_2>0$ and $p_1+p_2=1$. Write $g^{(k)}=\nabla u$ in phase $k$ and $h^{(k)}=a_k{g}^{(k)}$. Here $h$ is the positive conductivity flux; physical heat flux is $-h$. Continuity of temperature on a planar interface implies continuity of its tangential derivatives, while conservation gives continuity of normal heat flux. With interface normal $e_1$, these conditions areThe mean gradient is $E=p_1{g}^{(1)}+p_2{g}^{(2)}$. ThereforeBy the definition of effective conductivity, $⟨h⟩=a^{\ast }E$. ThusThe laminate conductivity is a weighted harmonic mean across the layers and a weighted arithmetic mean along them. This also explains why isotropic constituents can yield an anisotropic thermal conductivity tensor: flux must cross each resistance in sequence in the normal direction, whereas tangential transport occurs in parallel.

Thermal conductivity is the material response coefficient in Fourier's law. For an isotropic material it is a scalar $k$, with units $\mathrm{W}{\mathrm{m}}^{-1}{\mathrm{K}}^{-1}$; larger positive $k$ means a larger conductive heat flux for the same temperature gradient. It can depend on temperature and composition. Direction-dependent response in an anisotropic material is described by a thermal conductivity tensor. The two worked examples use stipulated positive constants, rather than measured values for named materials.

Thermal conductivity describes material response, whereas thermal resistance also includes geometry: for the steady bar, $R_{\mathrm{th}}=L/(kA)$. Doubling $k$ at fixed length, cross-sectional area and end temperatures halves thermal resistance and doubles the rate of heat transfer. Doubling length changes thermal resistance without changing the material's thermal conductivity. This distinction lets a designer improve cooling either by choosing a higher thermal conductivity or by shortening and widening the path. It also explains why the less conductive layer in thermal resistance takes the greater temperature drop.

Thermal diffusivity answers a different question: how rapidly a temperature disturbance spreads. Its usual model $\kappa =k/(\rho c_p)$ also involves mass density $\rho$ and specific heat capacity $c_p$, so equal thermal conductivities need not imply equal rates of warming.

Thermal diffusivity measures how rapidly thermal conduction smooths a temperature difference inside a material. Thermal conductivity measures the heat flux driven by a specified temperature gradient; thermal diffusivity also accounts for the heat capacity that must be warmed. A material can carry substantial heat yet change temperature slowly because it stores substantial internal energy per kelvin.

Write $\alpha =\kappa$ for thermal diffusivity, reserving $k$ for thermal conductivity. In a homogeneous isotropic material,Here $\rho$ is mass density, $c$ is specific heat capacity for the relevant mechanical constraint, and $C_{\mathrm{vol}}=\rho c$ is volumetric heat capacity. The familiar $k/(\rho c_p)$ uses specific heat capacity at constant pressure. For ordinary solids with negligible thermal expansion, the difference between the two constrained specific heat capacities is often neglected. A rigid fixed-volume model instead uses specific heat capacity at constant volume; a compressible moving fluid requires the accompanying work and transport terms. Thus the constraint is part of the approximation, not a choice made solely from the units. ^[ref]

Assume a stationary material in the continuum approximation, local thermal equilibration on times shorter than those resolved, no internal heating, no phase transition, and negligible convection and mechanical work. Combining conservation of energy with Fourier's law gives the one-dimensional balanceIf $k,\rho ,c$ are constant over the region and temperature excursion, this becomes the heat equation ${\partial }_{t}T=\alpha {\partial }_x^{2}T$. If $k$ varies, retain the differentiated product; replacing it with $k{\partial }_x^{2}T$ loses a term. Anisotropic materials need a thermal conductivity tensor. The scalar constant-$\alpha$ examples below deliberately exclude these complications. ^[ref]

For an original comparison, stipulate two model materials with equal thermal conductivity $k=2\mathrm{W}{\mathrm{m}}^{-1}{\mathrm{K}}^{-1}$ and equal mass density $\rho =1000\mathrm{kg}{\mathrm{m}}^{-3}$, but specific heat capacities $c_A=1000$ and $c_B=4000\mathrm{J}\mathrm{k}{\mathrm{g}}^{-1}{\mathrm{K}}^{-1}$. ThenAt the same temperature gradient, both have the same instantaneous heat flux by Fourier's law. At the same initial temperature profile and boundary conditions, material B takes four times as long to smooth a given spatial pattern. With fixed end temperatures, identical geometry and no sources, both eventually have the same steady profile and heat flux. The larger heat capacity changes the transient, not this steady state. These are stipulated parameters, not measurements of named substances.