Van der Waals throttling model

A hypothetical Van der Waals equation model illustrates positive and negative Joule-Thomson coefficient regions and a finite throttle that first warms, then cools. Use the molar convention already distinguished in Van der Waals equation:Here $v_{\mathrm{m}}$ is molar volume, $R$ the molar gas constant, $u_{\mathrm{m}}$ internal energy per mole, and $C_{V,\mathrm{m}}$ the stipulated constant molar heat capacity at fixed volume. The second equation is an additional caloric assumption: an equation of state alone does not specify the temperature dependence of internal energy. It satisfies the equilibrium identity $(\partial u_{\mathrm{m}}/\partial v_{\mathrm{m}}{)}_T=T(\partial p/\partial T{)}_{v_{\mathrm{m}}}-p=a_{\mathrm{m}}/v_{\mathrm{m}}^2$. The arbitrary energy reference is set to zero.

Define dimensionless variables $r=v_{\mathrm{m}}/b_{\mathrm{m}}$, $\theta =R{b}_{\mathrm{m}}T/a_{\mathrm{m}}$, $\pi =b_{\mathrm{m}}^{2}p/a_{\mathrm{m}}$ and $\eta =b_{\mathrm{m}}{h}_{\mathrm{m}}/a_{\mathrm{m}}$, where $h_{\mathrm{m}}$ is molar enthalpy. These differ from the critical-value scaling in Van der Waals law of corresponding states. The throttle calculation reduces toThus a prescribed inlet fixes $\eta$, and solving the first and last equations at the outlet pressure gives the final temperature. For an inlet $({\theta }_1,{\pi }_1)=(0.8,0.12)$ and outlet ${\pi }_2=0.025$, the model gives ${\theta }_2\simeq 0.752287$, a decrease of $0.047713$. The inlet $(2.2,0.12)$ instead gives ${\theta }_2\simeq 2.205786$, an increase of $0.005786$. The purple inlet $(1.45,0.30)$ initially warms but ends at ${\theta }_2\simeq 1.437585$ for the same outlet pressure. These are reduced toy values, not kelvin readings or experimental evidence. No physical gas parameters were fitted.

For a short inversion derivation, implicit differentiation of the Van der Waals equation at fixed pressure givesInsert this into $T(\partial v_{\mathrm{m}}/\partial T{)}_p=v_{\mathrm{m}}$ and substitute back into the equation of state. The Joule-Thomson inversion curve isPositive inversion pressure requires $r>3/2$. Its maximum pressure is $\pi =1/3$ at $r=3$, while the upper dilute limit is ${\theta }_{\mathrm{inv}}\to 2$. Using Van der Waals critical point values, the latter is $T_{\mathrm{inv},\max }/T_c=27/4$. The inversion locus depends on the equation of state; the chosen molar heat capacity additionally determines how much temperature changes along each finite throttle.^[ref]

The displayed region has $\theta >8/27$, above the model's critical temperature, and uses only $r>1$, $p>0$, $(\partial p/\partial v_{\mathrm{m}}{)}_T<0$ and positive $C_{p,\mathrm{m}}$. Subcritical calculations require attention to phase coexistence, metastability and the Maxwell construction; an unstable homogeneous continuation is not an equilibrium throttle endpoint. Even on a stable branch, this mean-field theory with constant $C_{V,\mathrm{m}}$ is a qualitative model, not an accurate inversion map for a particular real gas. Phase transitions, changing composition, appreciable heat leakage or bulk kinetic energy changes require a different property calculation or steady-flow energy balance. At phase coexistence, the smooth single-thermodynamic phase coefficient formula cannot replace a balance involving the phase fraction.