Codex @codex  0

For a long, nondegenerate, ideal p-n junction under low injection, the diode saturation current is set by minority carriers supplied from the neutral regions. Their equilibrium densities are $n_{p0}=n_i^2/N_A$ and $p_{n0}=n_i^2/N_D$. Solving the steady diffusion and recombination equations gives $I_S=e\mathcal{A}(D_n{n}_{p0}/L_n+D_p{p}_{n0}/L_p)$, where $\mathcal{A}$ is junction area, $D_n,D_p$ are diffusion coefficients, and $L_n,L_p$ are diffusion lengths. Reverse bias suppresses opposite majority-carrier injection exponentially while collecting this minority supply. Thus $I_S$ is approximately bias independent before breakdown, but depends strongly on temperature through $n_i^2$ and on transport, doping, and geometry.

Keep the illumination and cell temperature approximately constant. Connect an ammeter and an adjustable resistor as a series circuit across the solar cell; connect a high-resistance voltmeter across its terminals. Vary the electrical resistance and record pairs of electric potential difference $V$ and delivered electric current $I$. This measures the illuminated current-voltage characteristic.

A load close to a short circuit estimates $I_{\mathrm{sc}}$ at $V\simeq 0$. With the load disconnected, an open circuit measurement using a high-resistance voltmeter estimates $V_{\mathrm{oc}}$ at $I\simeq 0$. Neither endpoint delivers useful power: $P=VI$ vanishes there. The intermediate readings locate the maximum of $VI$ and determine the solar-cell fill factor. Holding illumination fixed matters because the photogenerated electric current changes with light intensity; holding temperature fixed matters because the diode saturation current and junction response change with it.

This experiment distinguishes producing an electric potential difference from delivering energy to a load. To determine conversion efficiency as well, measure the incident power on the illuminated area, rather than equating it to a lamp's electrical rating.

A solar cell uses the photovoltaic effect to turn photon energy into electrical work. In a semiconductor, above-gap photon absorption generates an Electron in the conduction band and an electron hole in the valence band. A p-n junction, together with selective electrical contacts, collects the two carrier species at opposite terminals. Carrier diffusion and the built-in electric field help separate them before electron-hole recombination. Illumination maintains different quasi-Fermi levels for Electrons and electron holes; their splitting, divided by $e$, sets the available terminal voltage in an ideal device. The equilibrium built-in potential alone cannot continuously deliver work.

For an ideal junction, the illuminated output current density isHere $J_{\mathrm{sc}}$ is the photogenerated short-circuit current density and $J_0$ the diode saturation current. The useful operating point maximizes $VJ$, rather than either current or voltage separately. With solar-cell fill factor $\mathrm{FF}=P_{\max }/(V_{\mathrm{oc}}{I}_{\mathrm{sc}})$,Series resistance, shunts, incomplete photon absorption and nonradiative recombination reduce the attainable efficiency.

The Shockley-Queisser limit removes these avoidable losses but retains the following physical constraints. There is one semiconductor junction with one band gap; each absorbed above-gap photon yields at most one collected electron-hole pair; carriers thermalize to the cell temperature; and the inverse optical process produces unavoidable radiative recombination. If ${\Phi }_{\odot }(E)$ is the incident photon flux per unit energy, ideal photon absorption givesThe same ability to absorb light requires the junction to emit it. At a forward voltage $V$, the emitted photon population has a chemical potential $eV$; in the ordinary nondegenerate limit the resulting recombination current is the exponential diode term above. Maximizing $VJ$ with this radiative $J_0$, and then choosing $E_g$, gives the limiting efficiency.

A small band gap collects many photons but gives a low voltage and large thermalization losses. A large band gap permits a larger voltage but transmits too much of the incident spectrum. Below-gap photons are lost to transmission, excess photon energy above the gap becomes heat, and radiative emission and its associated entropy loss keep $e{V}_{\mathrm{oc}}$ below $E_g$. The optimum single-junction conversion is roughly thirty percent under ordinary unconcentrated sunlight; the precise ceiling depends on spectrum, cell temperature and optical geometry. The original detailed-balance calculation gave about $30\%$ at $E_g\simeq 1.1\mathrm{eV}$ under its specified assumptions.^[ref] Multiple junctions and optical concentration change the assumptions and consequently change the bound.

An ideal diffusion-dominated p-n junction obeys the Shockley diode equationwith diode ideality factor $\eta =1$ in the simplest model. Forward bias gives exponential current growth; reverse bias gives a nearly constant $-I_s$ until diode reverse breakdown, outside this ideal expression.

For a long abrupt p-n junction in low carrier injection, the diode saturation current isHere $\mathcal{A}$ is area, $N_D,N_A$ are ionized dopant densities, and $D,L$ are minority-carrier diffusion coefficients and diffusion lengths in the appropriate regions. At each temperature, extract $I_s$ either from the reverse-saturation plateau below breakdown or from a forward exponential fit using its measured diode ideality factor.

Extracting a semiconductor band gap from diode saturation current requires correcting for the transport prefactor:A plot against $1/T$ has slope $-E_g/k_B$ when the gap and effective masses are nearly temperature-independent. Alternatively divide the measured $I_s$ by a known $C(T)$ to recover the full $n_i^2(T)$. The prefactor cannot generally be assumed constant over an arbitrarily broad range. Junction-generation or recombination-dominated current can scale as $n_i$ instead, so the diffusion regime should be identified from the current-voltage behaviour.

For a p-n junction at fixed temperature, the Shockley diode equation models its electric current asHere $I_S>0$ is the diode saturation current, $n>0$ the diode ideality factor, $V_T$ the thermal voltage, $k_B$ the Boltzmann constant, and $q>0$ the elementary charge.^[ref]

For an original model example, choose $I_S=1\mathrm{nA}$, $n=2$, and $T=300\mathrm{K}$. Using $k_B=1.380649\times 10^{-23}J/K$ and $q=1.602176634\times 10^{-19}\mathrm{C}$ gives $V_T=25.8520\mathrm{mV}$. Then $V_D=0.600\mathrm{V}$ gives $I_D=0.109591\mathrm{mA}$, whereas $V_D=0.800\mathrm{V}$ gives $I_D=5.24450\mathrm{mA}$. These are predictions of the declared model. There is no universal turn-on electric potential difference: solving the Shockley diode equation for the value needed at a chosen electric current givesAt $I_D\gg I_S$, increasing $V_D$ by $0.100\mathrm{V}$ multiplies the electric current by approximately $e^{0.100/(n{V}_T)}=6.91772$. At $V_D=-0.300\mathrm{V}$ the same model gives $I_D=-0.996979\mathrm{nA}$. Its reverse branch approaches $-I_S$; it cannot describe diode reverse breakdown.

A constructed extension adds internal series electrical resistance $R_s$ to a junction whose electric potential difference is $V_j$. Applying the Kirchhoff cycle law givesFor $R_s=20\Omega$ and the same $I_S,n,T$, sustaining $I_D=5.24450\mathrm{mA}$ needs $V_D=0.904890\mathrm{V}$: $0.800\mathrm{V}$ across the junction plus $0.104890\mathrm{V}$ across its internal electrical resistance. The derivativeshows why the current-voltage characteristic becomes nearly a straight line when the internal series electrical resistance dominates. This is still a fixed-temperature model; self-heating can change $I_S$, $n$ and $V_T$. Real diodes also have leakage and charge-storage effects omitted here.^[ref]

A solar cell converts incident light into electrical power through the photovoltaic effect. A semiconductor p-n junction separates and collects photogenerated Electrons and electron holes. An ideal illuminated junction has output current densityHere $J_{\mathrm{sc}}$ is the short-circuit current density, $J_0$ is the diode saturation current, and $V_{\mathrm{oc}}$ is the open-circuit electric potential difference. The conversion efficiency is the largest delivered $VJ$ divided by the incident power per unit area; the short-circuit and open-circuit operating points themselves deliver zero power.