Codex @codex  0

The current density $\mathbf{J}(\mathbf{r},t)$ describes the amount and direction of local electric charge transport per area per time. Its SI unit is $A/{\mathrm{m}}^2$. Through a small area element with unit normal $\mathbf{n}$, the contribution to electric current is $dI=\mathbf{J}\cdot \mathbf{n}dA$: the dot product selects transport through the surface. A current density tangent to the surface contributes zero. If current density is uniform and perpendicular to a wire's transverse slice, its magnitude $j=|\mathbf{J}|$ satisfiesHere $A$ is the wire cross-sectional area. For nonuniform current density, $I/A$ is only the average normal component, and the surface integral is needed. ^[ref].

Consider two separate uniform-flow cases, each carrying electric current $I=2\mathrm{A}$. A wire cross-sectional area of $1\mathrm{m}{\mathrm{m}}^2=10^{-6}{\mathrm{m}}^2$ gives $j=2\times 10^{6}A/{\mathrm{m}}^2$; doubling the wire cross-sectional area to $2\mathrm{m}{\mathrm{m}}^2$ gives $j=10^{6}A/{\mathrm{m}}^2$. Equal electric current can therefore mean different local transport intensity. This distinction matters for Joule heating, whose local power per volume depends on current density and electric field.

For a toy electron transport model, stipulate mobile electron number density $n=8\times 10^{28}{\mathrm{m}}^{-3}$ and drift velocity ${\mathbf{v}}_d=-10^{-4}m/s\hat{\mathbf{x}}$, with the positive unit normal $\hat{\mathbf{x}}$. Each electron has electric charge $-e$, where the elementary charge $e=1.602176634\times 10^{-19}\mathrm{C}$ is exact in SI. These are defined model inputs, rather than measured parameters of a particular material. ^[ref] The current density and its magnitude areFor wire cross-sectional area $A=1\mathrm{m}{\mathrm{m}}^2$ and constant transport over time $10\mathrm{s}$, this givesThe two minus signs make conventional current point opposite to the electron drift velocity. A small drift velocity can carry an appreciable electric current because many charge carriers contribute; it does not specify the propagation speed of an electrical disturbance.

A current element is the oriented infinitesimal wire contribution $Id{\mathbf{\ell }}^{\prime }$ inside the Biot-Savart law. For uniform axial current density across wire cross-sectional area $A$, $I=JA$ and $d^3{r}^{\prime }=Ad{\ell }^{\prime }$ imply $\mathbf{J}{d}^3{r}^{\prime }=Id{\mathbf{\ell }}^{\prime }$. This reduces a volume integral to a line integral in the thin-wire approximation. It is an integration contribution, not an isolated steady source. Conventional current runs opposite the drift of negatively charged electrons.

A motivating laboratory realization is The Hall Effect and Conductivity in Germanium by Rex Tayloe. The handout specifies a germanium sample holder with temperature and magnetic field control, a low-voltage supply, digital meters, and a current-reversing switch. Measure the sample dimensions, map the contacts, and establish the directions of electric current, magnetic field, and transverse voltage. At fixed temperature and zero magnetic field, sweep positive and negative electric currents and record longitudinal electric potential differences. A straight voltage-versus-electric current relation tests Ohm's law; sample geometry converts its slope to electrical resistivity. For the Hall effect, minimize the zero-field transverse offset and measure transverse voltage at all four combinations of $\pm I$ and $\pm B$, repeating for several electric currents. The readouts test longitudinal proportionality, transverse polarity, and transverse proportionality to electric current. These are protocol instructions, not reported measurement outcomes.^[ref]

For interpreting such measurements, an ideal uniform bar of wire cross-sectional area $A$ with longitudinal sensing contacts separated by $L$ gives $\sigma =LI/(A{V}_L)$. Four-terminal sensing suppresses voltage drops in current contacts when the voltage meter draws negligible electric current; it does not fix uncertain dimensions or a nonuniform current density. Reverse electric current and use $[V_L(+I)-V_L(-I)]/2$ to reject a constant voltage offset. Keep temperature stable, allow the current density to settle, and reduce electric current to test for Joule heating. Those are controls for interpreting the material coefficient, rather than reasons to assume every measured curve is linear.

For the transverse measurement define $\mathbf{J}=J_x\hat{\mathbf{x}}$, $\mathbf{B}=B_z\hat{\mathbf{z}}$, width $w$ along $y$, and thickness $d$ along $z$. Define $V_H=V(y=-w/2)-V(y=+w/2)=E_{y}w$, so $J_x=I/(wd)$ givesExtract the part odd in both electric current and magnetic field usingThis combination rejects a constant offset and longitudinal pickup even in magnetic field. It cannot reject another signal with the same two reversal symmetries. Check field polarity and magnitude independently; a sign error in the contact map changes the inferred Hall coefficient.

For one Drude model species in transverse open circuit, the steady Lorentz force balance is $0=q(\mathbf{E}+{\mathbf{v}}_d\times \mathbf{B})-m{\mathbf{v}}_d/\tau$ with $v_{d,y}=0$. Its $y$ component gives $E_y=v_{d,x}{B}_z$. ConsequentlyLongitudinal electrical conductivity and the Hall coefficient therefore separate number density from charge carrier mobility in this single-species model. Inferring a momentum relaxation time additionally requires an appropriate mass. A constant-field longitudinal measurement alone cannot supply all three.

A Hall coefficient is not universally the reciprocal of signed number density. For example, adding independent electron and electron hole contributions with densities $n,p$ and positive charge carrier mobilities ${\mu }_e,{\mu }_h$ in the weak-magnetic field limit givesThe Hall coefficient can vanish even while electrical conductivity is positive, and its sign weights charge carrier mobility as well as number density. The germanium handout explicitly asks students to track possible transverse sign changes with temperature; it does not establish a universal single-carrier interpretation. Real electronic band structure and unequal scattering also limit that interpretation.^[ref]

Electrical conductivity $\sigma$ measures the local response of current density to electric field. In the rest frame of an isotropic Ohmic conductor, the local form of Ohm's law isLarger positive electrical conductivity gives larger current density at the same electric field. It is a bulk material coefficient, distinct from the geometry-dependent electrical conductance of a whole component and from a sheet's surface conductivity. Electrical resistivity is ${\rho }_{\mathrm{el}}=1/\sigma$ in this scalar model. ^[ref].

The local and whole-wire forms fit together particularly neatly. For uniform current in a straight homogeneous wire, with length $L$, wire cross-sectional area $A$, constant electrical conductivity and terminal electric potential difference $V$, the axial electric field has magnitude $E=V/L$. ThusFor the defined electrical resistance example $\sigma =5\times 10^5(\Omega \mathrm{m}{)}^{-1}$, $L=1\mathrm{m}$, $A=10^{-6}{\mathrm{m}}^2$ and $V=5\mathrm{V}$, the local values are $E=5V/m$ and $j=2.5\times 10^{6}A/{\mathrm{m}}^2$; integrating gives $I=2.5\mathrm{A}$. One material law therefore supplies both a spatial description and a terminal relation.

The scalar form requires isotropy. In an anisotropic material the response can instead be a tensor, $J_i={\sum }_j{\sigma }_{ij}{E}_j$, and current density need not be parallel to electric field; uniaxial conductivity tensor is one existing example. These statements concern the material's rest frame. A moving electrical conductor instead uses the moving-conductor Ohm law.

Electrical resistance measures the electric potential difference needed to drive a given electric current through a component. For an Ohmic conductor under fixed material conditions, $R=V/I$ is constant and Ohm's law gives $V=IR$. The SI unit is the ohm, $1\Omega =1V/A$. At a fixed positive electric potential difference, increasing electrical resistance reduces electric current. Electrical conductance $G=1/R$ expresses the same response reciprocally. ^[ref].

For a straight uniform wire at rest, with constant electrical conductivity $\sigma >0$, length $L$ and wire cross-sectional area $A$, the uniform Ohmic conductor model givesThe electrical resistivity ${\rho }_{\mathrm{el}}$ characterizes the material; electrical resistance also includes geometry. Doubling length doubles $R$, while doubling wire cross-sectional area halves $R$, with material and temperature fixed. The uniform-field assumption includes insulated sides and equipotential end faces, as explained in uniform current in a straight homogeneous wire. ^[ref].

As a defined wire example, take $L=1\mathrm{m}$, $A=1\mathrm{m}{\mathrm{m}}^2$ and $\sigma =5\times 10^5(\Omega \mathrm{m}{)}^{-1}$. Then $R=2\Omega$; applying electric potential difference $5\mathrm{V}$ drives electric current $2.5\mathrm{A}$. With the same length and material, a second wire of wire cross-sectional area $2\mathrm{m}{\mathrm{m}}^2$ has $R=1\Omega$ and carries $5\mathrm{A}$ at that same electric potential difference. Fixing electric potential difference here differs from fixing electric current in the current density comparison: stating what is held fixed is essential.

The electric field does work on matter at local power per volumeHere $\mathbf{J}$ is current density and the dot product includes the relative direction. Positive $\mathbf{J}\cdot \mathbf{E}$ means energy passes from the field to matter; negative means matter supplies energy to the field. In general this is a work rate, not automatically an irreversible heating rate.^[ref]

For a stationary isotropic Ohmic conductor with real scalar electrical conductivity $\sigma >0$, local Ohm's law gives $\mathbf{J}=\sigma \mathbf{E}$. Thus the local Joule heating rate isThe electrical resistivity ${\rho }_{\mathrm{el}}$ has units $\Omega \mathrm{m}$, and electrical conductivity has units $(\Omega \mathrm{m}{)}^{-1}$. These formulas use the material's rest frame and dissipative conduction current density. Moving media, complex conductivity, and additional storage or transport processes require their appropriate energy balance rather than this scalar substitution.

For uniform current in a straight homogeneous wire of length $L$, wire cross-sectional area $A$ and constant electrical conductivity, $E=V/L$, $J=I/A$ and $R=L/(\sigma A)$. The volume integral recovers terminal power:As a numerical check, the wire already used in electrical resistance has $L=1\mathrm{m}$, $A=10^{-6}{\mathrm{m}}^2$, $\sigma =5\times 10^5(\Omega \mathrm{m}{)}^{-1}$ and $V=5\mathrm{V}$. It gives $J=2.5\times 10^{6}A/{\mathrm{m}}^2$, $p_{\mathrm{vol}}=1.25\times 10^{7}W/{\mathrm{m}}^3$ and $P=12.5\mathrm{W}$, agreeing with $I=2.5\mathrm{A}$ and $R=2\Omega$. Concentrating the same electric current in a smaller wire cross-sectional area therefore raises the local heating rate if electrical resistivity stays fixed.

Ohm's law states that an Ohmic conductor has electric current proportional to its applied electric potential difference, with constant electrical resistance under fixed material conditions:Here $V=\varphi (A)-\varphi (B)$ is the terminal electric potential difference, and positive $I$ enters at $A$ and exits at $B$. This sign convention makes $VI$ the electrical power absorbed. The straight-line relation through the origin lets one constant predict the response at many applied electric potential differences. Merely defining $R=V/I$ at one nonzero operating point does not establish Ohm's law: a component may have a ratio that varies with applied electric potential difference. Material and temperature must be specified and held fixed; many components have a nonlinear response. ^[ref].

For the ideal resistor model $R=2\Omega$ at electric potential difference $V=5\mathrm{V}$,This power is converted to internal energy by Joule heating; a watt is a joule per second. If the model holds for time $10\mathrm{s}$, the transferred energy is $125\mathrm{J}$. Doubling electric potential difference doubles electric current and quadruples power for the same fixed $R$. The model keeps material temperature fixed even while calculating Joule heating; appreciable changes in temperature may require a changing electrical resistance. ^[ref].

In 1827, Georg Ohm published his mathematical account of electrical transport in Die galvanische Kette, mathematisch bearbeitet. On printed page 36, his relation $S=A/L$ expresses electric current in terms of total driving tension and a reduced length incorporating electrical conductivity and geometry. This is historical notation: his $A$ is not the wire cross-sectional area used here, and his $L$ is not simply the wire's physical length. The striking idea is that material response and geometry can be combined into one quantity governing an electrical circuit. ^[ref].

PHYWE's documented experiment uses a one-metre slide wire, a connection box, an unknown resistor, a known comparison resistor, a supply, and a digital multimeter in steady-current mA mode as the null detector. Its two yellow detector leads join the fixed-resistor junction and the slider. Move the slider until the indicated electric current vanishes; read the two wire lengths on the ruler and infer the unknown electrical resistance from their ratio. The guide advises changing the comparison resistor if no null is reachable or the slider lies near an end.^[ref]

The inference requires uniform electrical resistivity and wire cross-sectional area, so the two wire electrical resistances have the ratio of their lengths, by $R={\rho }_{\mathrm{el}}L/A$. Retaining PHYWE's labeling, its equation (6) is $R_x=R_C{\ell }_1/{\ell }_2$, where $R_C$ is the comparison electrical resistance. This is a different arm placement from our schematic. The guide's example table reports larger discrepancies near wire ends.^[ref]

Useful additional controls distinguish a true null measurement from an insensitive or disconnected detector. Check the detector zero with the supply off, then move the adjustable arm slightly to either side of the candidate balance and verify opposite detector signs. Reconnect the unknown with short, secure leads and repeat the balance. Any lead or contact electrical resistance included in that arm contributes to the inferred value, even though a detector lead carries no electric current at exact balance. For very small unknown electrical resistances, four-terminal sensing addresses this separate connection problem; a detector null alone does not remove it.

Check for Joule heating by repeating at lower supply electric potential difference and with shorter powered intervals, holding ambient temperature fixed. At balance the unknown still dissipates powerHalving $V_s$ quarters this power while halving ideal detector sensitivity. A balance that moves with excitation or elapsed time suggests changing electrical resistance, including self-heating; it is not explained by passive detector loading alone. These are proposed controls, not claimed outcomes of PHYWE's experiment. Standard-resistor accuracy, wire uniformity, contact reproducibility and finite detector resolution still limit the electrical measurement. Large electrical resistances also make unwanted leakage paths consequential.

The wire cross-sectional area is the area of a slice perpendicular to the wire's axis. For a round wire of radius $a$, it is $A=\pi a^2$. It enters both the uniform-flow formula $I=jA$ for current density and the formula $R=L/(\sigma A)$ for the electrical resistance of a uniform Ohmic conductor.