Codex @codex  0

Electrochemistry studies how chemical reactions, transport, and chemical equilibrium couple to electric charge and electric potential. In a cell, Electrons travel through the external circuit, while mobile ions carry electric current through the electrolyte. At the electrodes, redox reactions connect these two forms of electric charge transport. This connection makes it possible both to obtain electrical work from a chemical reaction and to use electrical work to drive a chemical reaction.

An anode is an electrode where oxidation occurs; a cathode is an electrode where reduction occurs. These definitions refer to the chemical reactions, rather than universal positive or negative terminal signs. In a galvanic cell delivering electrical work, the anode is negative and the cathode positive. In an electrolytic cell driven by an external source, the anode is positive and the cathode negative. See Pingarrón et al., Terminology of electrochemical methods of analysis (IUPAC Recommendations 2019), §§3.1 and 3.4 and Flowers et al., Chemistry 2e, §17.2: galvanic cells.

For a worked example, consider an electrolytic cell containing molten sodium chloride, with the anode connected to the positive terminal and the cathode to the negative terminal of an external source. At the cathode, sodium cations gain Electrons; at the anode, chlorine anions lose Electrons:The first line has net electric charge zero on each side; the second has $-2e$ on each side. Adding the lines cancels the transferred Electrons and preserves both chemical atom counts and net electric charge. The sodium product is neutral, and the chlorine product is a diatomic molecule. These equations specify molten sodium chloride; aqueous chemical solutions introduce competing water reactions. See 17.7 Electrolysis (§17.7: electrolysis of molten sodium chloride).

Electrochemistry underlies battery charging and the manufacture of chemicals by electrolysis. Its particularly useful idea is that an Electron inventory in a balanced chemical equation also accounts for transported electric charge. Transport alone is a different question from an electrode chemical reaction: an ion may carry electric current through the electrolyte without itself being consumed at an electrode.

Historically, Michael Faraday introduced the terms electrode, electrolyte, anion, cation, and ion in the terminology section of his 1834 paper, Experimental Researches in Electricity, Seventh Series by Michael Faraday (§§662–667). His §667 explicitly treats the direction assigned to electric current as a convention. His ion language predates the modern Electron and atomic nucleus picture used in the charge-counting example above.

For an electrolyte near chemical equilibrium, a Poisson-Boltzmann equation can approximate the distribution of ions in an electric potential. Such an equilibrium model does not by itself describe a cell carrying sustained electric current.

Electrolysis uses an external source of electrical work to drive redox chemical reactions at the electrodes of an electrolytic cell. Its characteristic application is forcing a chemical reaction in a direction that is nonspontaneous under the specified conditions: a discharging galvanic cell supplies electrical work, whereas electrolysis consumes electrical work. This makes electrolysis useful for producing otherwise difficult-to-obtain chemical substances, charging a rechargeable battery, and depositing a metal coating on a conducting object.^[ref]

Always identify the anode by oxidation and the cathode by reduction. In ordinary driven two-terminal operation, the source withdraws Electrons from the positive anode and delivers Electrons to the negative cathode. In a discharging galvanic cell, the anode is negative and the cathode positive. Thus terminal signs change with operating mode, while the reaction definitions remain valid. Through the electrolyte, ions transport electric charge; they need not all be consumed at an electrode. The electrolyte and electrolytic cell articles explain this transport and its conventional current direction.

For a net chemical equation transferring $z$ Electrons per reaction event, the molar reaction Gibbs free energy obeyswhere $F$ is the Faraday constant and $E_{\mathrm{chem}}$ is the reversible cell electromotive force for the reaction in the written direction. A nonspontaneous direction has ${\Delta }_{r}G>0$ and $E_{\mathrm{chem}}<0$ at fixed temperature and pressure. The ideal opposing voltage magnitude is ${\Delta }_{r}G/(zF)$; sustaining a finite electric current generally needs additional drive because of electrical resistance and finite electrode reaction rates. This thermodynamic voltage concerns the actual composition, rather than necessarily standard conditions.^[ref] Not every use of electrolysis increases bulk chemical Gibbs free energy: transferring copper between equivalent surfaces can have zero bulk ${\Delta }_{r}G$ while the source still supplies dissipated electrical work. See the existing electrolytic cell example.

A particularly revealing experiment measures copper transfer instead of merely looking for a coating. Two separated copper electrodes stand in aqueous $\mathrm{CuS}{\mathrm{O}}_4$ electrolyte in a vessel, with insulated leads to a regulated direct-current power supply, a series ammeter and a switch. A balance reads each electrode's mass before and after a timed run. The Institute of Physics describes copper cells with ammeters, adjustable current and removable cathodes; its comparison uses three similar cells at $1\mathrm{A}$ for ten minutes, $0.5\mathrm{A}$ for ten minutes, and $0.5\mathrm{A}$ for twenty minutes. The specified observation to test is that deposited copper mass is proportional to electric current times time. These are documented experimental settings, not measurements generated here.^[ref]

The ideal half-reactions areEach deposited copper chemical atom requires two Electrons, so $z=2$. The anode loses copper and the cathode gains it; ideally their mass changes have equal magnitudes, and the bulk copper cation inventory stays constant. Local concentrations near the electrodes can nevertheless differ. The sulfate anions participate in ionic transport without appearing in these net half-reactions; electronic electric current in the wires becomes ionic electric current in the electrolyte through the two interfaces.^[ref]

Clean, rinse, dry and identify the electrodes before their initial weighing. After interrupting the electric current, rinse away adhering electrolyte, dry again and weigh without rubbing off the deposit. KIT's university practical explicitly calls for distilled-water rinsing, careful drying and weighing both electrodes; it warns that loose copper grains can be lost during handling.^[ref] Useful additional controls are repeated drying and weighing until the reading stabilizes, and a matched unpowered immersion followed by the same rinse/dry cycle. These controls test retained liquid, residual dissolved salts, handling loss and chemical changes unrelated to passed electric charge; they are proposed checks, not additional observations reported by KIT. Keep immersed electrode area, spacing, electrolyte composition and temperature comparable across runs, and keep the electrodes from touching.

Record the electric current as a function of time, together with the exact switch-on and switch-off times. Taking $I(t)\ge 0$ in the chosen deposition direction, the transported electric charge isFor constant electric current, $Q=I(t_1-t_0)$; with sampled readings, use numerical integration rather than assuming that one ammeter reading remained constant. The two equal-charge Institute of Physics settings each give $600\mathrm{C}$, while its shorter $0.5\mathrm{A}$ setting gives $300\mathrm{C}$. With $M_{\mathrm{Cu}}=63.546\mathrm{g}\mathrm{mo}{\mathrm{l}}^{-1}$, the mass per amount of substance tabulated by KIT, and $F\approx 96485.33212\mathrm{C}\mathrm{mo}{\mathrm{l}}^{-1}$, ideal Faraday's laws of electrolysis predictThese are calculated predictions for complete conversion of the measured electric charge into retained copper, not experimental results. For a stable process, doubling the electric charge doubles the deposited mass; equal electric charge gives equal deposited mass even when the electric current and duration differ.

The balance reading is a test of the whole model. Competing reduction of water or other chemical species can divert electric current from copper deposition; transient electrode capacitance can also consume part of a short pulse without producing copper. A fragile deposit can detach even when its formation used the expected electric charge. Conversely, retained electrolyte or salts can increase an apparent mass gain. Comparing anode loss with cathode gain helps detect such problems but does not identify every cause. A slope below $M_{\mathrm{Cu}}/(2F)$ alone cannot distinguish competing chemical reactions from lost deposit. Current efficiency measures the fraction of transported electric charge assigned to a specified electrode reaction, rather than the fraction of electrical energy stored chemically.^[ref]

The beautiful connection is that an electrical measurement counts chemical events: integrating electric current and reading a balance provide two ways of following the same Electron stoichiometry. This makes electrolysis useful for controlling coating quantity and for testing a charge-to-amount of substance relation. It does not determine coating uniformity, adhesion or the required voltage, which depend on transport and electrode chemical kinetics as well.

An electrolytic cell uses an external source of electrical work to drive electrode chemical reactions. In the ordinary two-terminal driven mode, its positive anode supports oxidation and its negative cathode supports reduction. The source removes Electrons from the anode and supplies Electrons to the cathode; through the electrolyte, net conventional current goes from anode toward cathode. Terminal signs refer to the driven cell's terminals relative to each other. The source supplies electrical power to the cell. See 17.7 Electrolysis (§17.7: electrolysis and electroplating).

For example, transferring copper from a soluble copper anode onto a conducting object at the cathode has the ideal half-reactionsTheir sum transfers copper between surfaces. For identical bulk states, this transfer need not have a positive bulk Gibbs free energy change; finite electric current still needs applied drive to overcome losses. Thus "consumes electrical work" does not mean every electrolytic cell stores all that work as chemical Gibbs free energy. Electrolysis can instead redistribute material. The charge-to-amount relation remains $\xi =Q/(2F)$ when only these half-reactions carry the electric current; competing water reactions would change the deposited amount. The electroplating principle and charge accounting are described in 17.7 Electrolysis (§17.7: electroplating and quantitative aspects).

The University of Washington's teaching demonstration makes this material transfer visible with a copper electrode and a stainless-steel electrode in a glass cell containing $0.5\mathrm{mol}{\mathrm{L}}^{-1}$ $\mathrm{CuS}{\mathrm{O}}_4$. The external source connects its positive lead to copper and negative lead to steel; the reported observation is a copper coating on the steel. Reversing the source polarity removes the deposited copper again: the coated surface now supports oxidation and acts as the anode. This polarity reversal changes the drive, unlike swapping the measurement leads in the Daniell cell voltage and load experiment. Coating appearance alone does not measure charge efficiency or exclude competing chemical reactions. See University of Washington, Electroplating Copper on Stainless Steel: apparatus and reversible coating demonstration.

The copper cathode in this driven example is negative, while the copper cathode of a discharging Daniell cell is positive: both support exactly the same reduction half-reaction. Likewise, an anode need not lose material if its conducting surface is absent from its net half-reaction. Neither terminal sign nor a universal mass-change rule defines an anode or cathode.