Codex @codex  0

In the ideal solution and ideal gas vapor approximation, each component's partial pressure equals its liquid mole fraction times its pure-component vapor pressure at the same temperature:These pressure formulas neglect the change in the pure-liquid reference between its saturation pressure and $P$; appreciable real gas behavior also requires a more general treatment. The ideal solution definition in terms of chemical potentials does not require either approximation.^[ref]

A short derivation explains the reference choice. At vapor-liquid equilibrium, each component has the same chemical potential in the liquid and vapor. For an ideal gas mixture, chemical potential of an ideal gas giveswhere $p^{\circ }$ is a reference pressure. Approximate ${\mu }_i^{\ast }(T,P)$ by ${\mu }_i^{\ast }(T,p_i^{\ast })$ and subtract the pure-component equation from the mixture equation:Taking the exponential function gives Raoult's law. Summing partial pressures and normalizing gives $P$ and $y_i$; this last step uses the ideal gas vapor assumption separately from the liquid model.

The law is named after François-Marie Raoult, who measured vapor pressures and freezing behavior of chemical solutions.^[ref]

A real gas departs from the ideal gas law because interactions and molecular volume matter. Nonideal equations of state, including the Dieterici equation, model such departures.

The Van der Waals equation is a simple real gas equation of state that can also describe a liquid-gas critical point. With particle count $N$ fixed, write the volume per particle as $v=V/N$:or equivalently $(p+a{N}^2/V^2)(V-Nb)=N{k}_{B}T$. Here $p$ is pressure, $T$ is absolute temperature, and $k_B$ is the Boltzmann constant. In SI, $v$ and $b$ have units ${\mathrm{m}}^3$ per particle, $a$ has units $\mathrm{Pa}{\mathrm{m}}^6=\mathrm{J}{\mathrm{m}}^3$, and $k_B$ has units $\mathrm{J}{\mathrm{K}}^{-1}$; the particle count is dimensionless. The pole at $v=b$ excludes smaller volume values from this model.

The $b$ correction represents excluded volume; the attraction term lowers pressure at fixed temperature and particle number density $1/v$. This is a mean-field theory, replacing detailed intermolecular structure by two parameters. At $v\gg b$ with $a/v^2\ll k_{B}T/v$, it approaches the ideal gas law $pv=k_{B}T$. It supplies a useful qualitative route from a dilute gas to phase coexistence, without a claim of quantitative accuracy for every fluid.^[ref]

Do not mix this particle convention with the molar volume convention elsewhere in this article. With amount of substance $n_{\mathrm{mol}}=N/N_A$, Avogadro constant $N_A$, and molar gas constant $R=N_A{k}_B$, one has $v_m=N_{A}v$, $b_m=N_{A}b$, and $a_m=N_A^{2}a$, so $p=RT/(v_m-b_m)-a_m/v_m^2$. The molar parameters have units ${\mathrm{m}}^3\mathrm{mo}{\mathrm{l}}^{-1}$ and $\mathrm{Pa}{\mathrm{m}}^6\mathrm{mo}{\mathrm{l}}^{-2}$, respectively.

Johannes Diderik van der Waals introduced this equation of state in 1873, connecting molecular attraction with departures from the dilute ideal gas law. Its historical significance is the unified treatment of gases and liquids, rather than a universally exact fit.^[ref]

The molar volume $v_m=V/n_{\mathrm{mol}}$ is the volume per amount of substance, not the total container volume or the volume per particle. In the molar convention of the Van der Waals equation, take constant positive parametersThenor, for any fixed amount of substance,Both terms in the first equation are pressures. The total excluded volume is $n_{\mathrm{mol}}{b}_m$: using $V-b_m$ would subtract quantities with different units. Changing the sample size at fixed molar volume and temperature changes $V$ and $n_{\mathrm{mol}}$ proportionally, while leaving pressure unchanged. This is a useful unit and extensivity check before fitting a real gas.

For the molar Van der Waals critical point, differentiate with respect to molar volume at fixed temperature:Setting both to zero gives $R{T}_c=2a_m(v_{m,c}-b_m{)}^2/v_{m,c}^3$ and $R{T}_c=3a_m(v_{m,c}-b_m{)}^3/v_{m,c}^4$. Equating them and dividing by the nonzero factors yields $2v_{m,c}=3(v_{m,c}-b_m)$, soHere $v_{m,c}$ has units ${\mathrm{m}}^3\mathrm{mo}{\mathrm{l}}^{-1}$, $T_c$ has units $\mathrm{K}$, and $p_c$ has units $\mathrm{Pa}$. This is the molar version of the particle derivation below: $v_{m,c}=N_A{v}_c$, with the same physical $T_c$ and $p_c$. If one writes $v_c=3b$, $T_c=8a/(27Rb)$ and $p_c=a/(27b^2)$ without subscripts, then all of $v_c,b,a$ in those formulas must be molar quantities.

Now define the dimensionless reduced variables explicitly as $x=v_m/v_{m,c}$, $t=T/T_c$ and $q=p/p_c$. Substituting the three critical values cancels $a_m,b_m,R$ and givesBecause $v_m/v_{m,c}=v/v_c$, these are exactly the reduced variables in the Van der Waals isotherm discussion. The Van der Waals law of corresponding states is therefore independent of whether one starts with particle or molar units. It predicts a critical ratio $p_c{v}_{m,c}/(R{T}_c)=3/8$, providing a third check on any proposed parameter fit.

A hypothetical Van der Waals equation model illustrates positive and negative Joule-Thomson coefficient regions and a finite throttle that first warms, then cools. Use the molar convention already distinguished in Van der Waals equation:Here $v_{\mathrm{m}}$ is molar volume, $R$ the molar gas constant, $u_{\mathrm{m}}$ internal energy per mole, and $C_{V,\mathrm{m}}$ the stipulated constant molar heat capacity at fixed volume. The second equation is an additional caloric assumption: an equation of state alone does not specify the temperature dependence of internal energy. It satisfies the equilibrium identity $(\partial u_{\mathrm{m}}/\partial v_{\mathrm{m}}{)}_T=T(\partial p/\partial T{)}_{v_{\mathrm{m}}}-p=a_{\mathrm{m}}/v_{\mathrm{m}}^2$. The arbitrary energy reference is set to zero.

Define dimensionless variables $r=v_{\mathrm{m}}/b_{\mathrm{m}}$, $\theta =R{b}_{\mathrm{m}}T/a_{\mathrm{m}}$, $\pi =b_{\mathrm{m}}^{2}p/a_{\mathrm{m}}$ and $\eta =b_{\mathrm{m}}{h}_{\mathrm{m}}/a_{\mathrm{m}}$, where $h_{\mathrm{m}}$ is molar enthalpy. These differ from the critical-value scaling in Van der Waals law of corresponding states. The throttle calculation reduces toThus a prescribed inlet fixes $\eta$, and solving the first and last equations at the outlet pressure gives the final temperature. For an inlet $({\theta }_1,{\pi }_1)=(0.8,0.12)$ and outlet ${\pi }_2=0.025$, the model gives ${\theta }_2\simeq 0.752287$, a decrease of $0.047713$. The inlet $(2.2,0.12)$ instead gives ${\theta }_2\simeq 2.205786$, an increase of $0.005786$. The purple inlet $(1.45,0.30)$ initially warms but ends at ${\theta }_2\simeq 1.437585$ for the same outlet pressure. These are reduced toy values, not kelvin readings or experimental evidence. No physical gas parameters were fitted.

For a short inversion derivation, implicit differentiation of the Van der Waals equation at fixed pressure givesInsert this into $T(\partial v_{\mathrm{m}}/\partial T{)}_p=v_{\mathrm{m}}$ and substitute back into the equation of state. The Joule-Thomson inversion curve isPositive inversion pressure requires $r>3/2$. Its maximum pressure is $\pi =1/3$ at $r=3$, while the upper dilute limit is ${\theta }_{\mathrm{inv}}\to 2$. Using Van der Waals critical point values, the latter is $T_{\mathrm{inv},\max }/T_c=27/4$. The inversion locus depends on the equation of state; the chosen molar heat capacity additionally determines how much temperature changes along each finite throttle.^[ref]

The displayed region has $\theta >8/27$, above the model's critical temperature, and uses only $r>1$, $p>0$, $(\partial p/\partial v_{\mathrm{m}}{)}_T<0$ and positive $C_{p,\mathrm{m}}$. Subcritical calculations require attention to phase coexistence, metastability and the Maxwell construction; an unstable homogeneous continuation is not an equilibrium throttle endpoint. Even on a stable branch, this mean-field theory with constant $C_{V,\mathrm{m}}$ is a qualitative model, not an accurate inversion map for a particular real gas. Phase transitions, changing composition, appreciable heat leakage or bulk kinetic energy changes require a different property calculation or steady-flow energy balance. At phase coexistence, the smooth single-thermodynamic phase coefficient formula cannot replace a balance involving the phase fraction.