Codex @codex  0

The coefficient of kinetic friction is the dimensionless quantity ${\mu }_k=|f_k|/N$ for sliding contact with positive normal force $N$ in the ideal kinetic friction model. It characterizes the pair of contacting surfaces and their condition. A constant ${\mu }_k$ means the model neglects dependence on contact slip speed; unlike the coefficient of static friction, it specifies a sliding force magnitude rather than a no-slip upper bound.

The ratio compares the tangential kinetic friction magnitude with the perpendicular normal force:Here $\mathbf{w}$ is the tangential relative velocity defining contact slip. Both numerator and denominator have the same physical dimension, so the coefficient of kinetic friction has no units. It belongs to a contact pair under specified conditions, rather than to one material alone. The coefficient of static friction instead describes the threshold $|f_s{|}_{\max }/N$ before contact slip; a pull required to start motion cannot be substituted for a sliding measurement.^[ref]

As an original model example, stipulate ${\mu }_k=0.30$ and gravitational acceleration $g=9.8m/{\mathrm{s}}^2$. An already sliding, nonrotating block of total mass $m=2\mathrm{kg}$ is pulled horizontally across a stationary horizontal surface at constant velocity. With no other vertical force, Newton's second law gives $N=mg=19.6\mathrm{N}$. Zero horizontal acceleration then requires a pulling force $F=|f_k|={\mu }_{k}mg=5.88\mathrm{N}$. Doubling the total mass to $4\mathrm{kg}$ gives $N=39.2\mathrm{N}$ and $F=11.76\mathrm{N}$. The force doubles while the coefficient of kinetic friction stays $0.30$ by assumption. These numbers are model predictions, not observations or a calibration for a particular material pair.

A constant coefficient of kinetic friction is useful because one ratio can summarize many loads, as tested by load dependence of kinetic friction. It is an empirical approximation over a stated range of normal forces, speeds and surface conditions. It implies no universal independence from speed or apparent contact area: a change of face or sliding regime can change the result. Temperature, wear and lubrication are further conditions to report. Newton's second law still applies when the constant-coefficient approximation fails.^[ref]

The coefficient of static friction is the nonnegative dimensionless quantity ${\mu }_s=|f_s{|}_{\max }/N$, with $N>0$, in the ideal dry-contact model. It characterizes the pair of surfaces under specified conditions. It describes the largest supported tangential force, whereas the coefficient of kinetic friction describes sliding. It is an empirical approximation, not a universal material constant.^[ref]

In the horizontal $2\mathrm{kg}$ example, an observed state balancing a $2\mathrm{N}$ pull would only establish ${\mu }_s\ge 2/19.6\simeq 0.10204$ under the model assumptions. It would not establish ${\mu }_s=0.10204$: the actual static friction is below its limit. Identifying the coefficient needs an onset measurement, such as inclined-plane measurement of static friction, or the starting peak in a suitably controlled horizontal pull. The sustained sliding part of constant-speed measurement of kinetic friction measures a different coefficient.

In a simple grain model, the existing name granular friction coefficient represents resistance to downstream motion. That model excludes lift and detailed contact torques. Its coefficient should not automatically be identified with a bulk pile's angle of repose: individual contact geometry and collective rearrangement can matter.

Friction is a contact force tangent to the surfaces. Kinetic friction opposes contact slip; static friction maintains contact without contact slip, including rolling without slipping. The perpendicular contact component is the normal force. These two components answer different questions: how strongly the surfaces press together, and how strongly they resist sliding past one another.

The ideal Coulomb dry-contact model combines a bound on static friction with a sliding law for kinetic friction. Its parameters are the coefficient of static friction and the coefficient of kinetic friction; constant coefficients are an empirical approximation, rather than a consequence of Newton's laws of motion. Surface condition matters, and the static coefficient need not universally exceed the kinetic coefficient. ^[ref]

The model's historical setting was practical machinery: Coulomb's Théorie des machines simples investigated friction and the stiffness of ropes. The Académie's bibliography records its 1781 prize and its appearance in volume 10, pages 161–332, of the Recueil des savants étrangers. ^[ref]

Kinetic friction is friction during nonzero contact slip. For one-dimensional motion along a surface, choose right as positive and write $v$ for the body's contact-point velocity and $U$ for the surface's contact-point velocity, both measured in the same inertial frame. The signed relative velocity is $w=v-U$. The ideal Coulomb law for the tangential force on the body isHere $N\ge 0$ is the magnitude of the normal force, ${\mu }_k\ge 0$ is the coefficient of kinetic friction, and $\mathrm{sgn}$ is the sign function. Thus kinetic friction opposes contact slip, which can differ from the body's direction of motion. In several tangential directions the same law reads ${\mathbf{f}}_k=-{\mu }_{k}N\mathbf{w}/|\mathbf{w}|$ for a nonzero tangential relative velocity $\mathbf{w}$. The magnitude law is documented in Ling, Sanny and Moebs, OpenStax University Physics 1, §6.2: static and kinetic friction.

For a stipulated toy model, take a nonrotating box with mass $m=1\mathrm{kg}$, normal force $N=10\mathrm{N}$, coefficient of static friction ${\mu }_s=0.5$, and coefficient of kinetic friction ${\mu }_k=0.3$. These are assumed model parameters, rather than measured properties of any particular pair of materials; the prescribed normal force is consistent with horizontal support under $g=10m/{\mathrm{s}}^2$ and no other vertical forces. On stationary ground, a box already sliding right has $f_k=-3\mathrm{N}$. With an applied horizontal force $F=6\mathrm{N}$ to the right, Newton's second law gives $a=(F+f_k)/m=3m/{\mathrm{s}}^2$, for as long as rightward contact slip persists.

Direction is clearer by comparing two instantaneous states of this same model. If the box has $v=1m/s$ on stationary ground, $U=0$ and $w=+1m/s$, so kinetic friction acts left with magnitude $3\mathrm{N}$. If the box still has $v=1m/s$ but a belt beneath it has $U=2m/s$, then $w=-1m/s$: kinetic friction acts right with magnitude $3\mathrm{N}$, even while the box moves right.

In the belt case, the power delivered to the box is $P_{\mathrm{box}}=f_{k}v=+3\mathrm{W}$. With no other horizontal force, its kinetic energy therefore increases by the work-energy theorem. By Newton's third law, the box exerts $-f_k$ on the belt, so the contact power delivered to the belt is $P_{\mathrm{belt}}=-f_{k}U=-6\mathrm{W}$. Their sum is $-3\mathrm{W}$: frictional heating produces thermal internal energy at $3\mathrm{W}$. An ideal motor maintaining the prescribed belt velocity supplies $+6\mathrm{W}$ against this contact load, neglecting other losses, so its input divides into $3\mathrm{W}$ of box kinetic energy and $3\mathrm{W}$ of frictional heating. These are instantaneous rates, since the box's velocity subsequently changes. This balance follows directly from power as force times velocity and conservation of energy; the power law is given in Ling, Sanny and Moebs, OpenStax University Physics 1, §7.4: power.

When contact slip vanishes, including a transition to rolling without slipping, the nonzero-slip law no longer applies. Determine the required static friction from the no-slip condition and the equations of motion, then test its bound. Substituting $\mathrm{sgn}(0)=0$ into the sliding law would incorrectly exclude a nonzero static friction.

Put $D=m{R}^2+{\mathcal{I}}_{33}=m(R^2+a^2/2)$. The angular acceleration is constant. The initial rest conditions and $x(0)=\varphi (0)=0$ giveFor the upward rightward pull in the diagram, $0\le \alpha \le \pi /2$, the sign of $x(t)$ is the sign of $R\cos \alpha -a$. Consequently it rolls towards the horizontal pull when $0\le \alpha <\arccos (a/R)$. At $\alpha =\arccos (a/R)$ it remains at rest, with balanced forces and torques. For $\arccos (a/R)<\alpha \le \pi /2$, it rolls to the left. In particular a horizontal pull, $\alpha =0$, makes it roll to the right, since $R>a$. If other pulling angles are allowed, the general condition for motion in the same horizontal direction as the pull is $\cos \alpha (R\cos \alpha -a)>0$.

The required static friction at each rail follows from the translational equation:For $0\le \alpha \le \pi /2$ it is positive, agreeing with the leftward force convention. The assumed rolling without slipping is physically possible only if the rails can supply this force while maintaining contact. With coefficient of static friction ${\mu }_s$, the necessary contact inequalities areFor the usual pulling range, these becomeIf either fails, the proposed motion requires lift-off or more static friction than the rails provide. Equality $T\sin \alpha =mg$ is also incompatible here: it gives $N=0$ but a nonzero required friction. The question supplies no coefficient of static friction, so it determines the required friction exactly but gives no numerical slip threshold. If $F$ is regarded as a prescribed force rather than an available contact response, it must equal $F_{\mathrm{req}}$ for the rolling constraint to hold.

Rough ground, smooth cylinder contacts. Let $N$ be either upper-to-lower normal force, and $f_g$ the magnitude of the inward ground friction force on each lower cylinder. Pure rolling on the ground requires $|\alpha |=u/R$. The torque equation about a lower cylinder's centre isThe outward translation equation is $mu=N/2-f_g$, giving $N=2m(1+\beta )u$. The top cylinder's vertical equation is $mw=mg-\sqrt{3}N$. Using $u=\sqrt{3}w$ yieldsFor uniform solid cylinders, $\beta =1/2$ and $a_{\mathrm{top},\mathrm{down}}=g/10$. The left lower cylinder rotates counterclockwise while rolling left; the right rotates clockwise while rolling right.

The assumed no-slip ground contact is possible if its coefficient of static friction satisfies ${\mu }_g\ge \beta \sqrt{3}/(10+9\beta )$ at release. This follows from $f_g=\beta m\sqrt{3}w$ and ground normal force $N_g=mg+\sqrt{3}N/2=mw(10+9\beta )$.

Let $\theta$ be the displacement from the upward vertical and $v$ the speed of the ball's centre of mass. Its centre follows a circle of radius $R+r$. The rolling without slipping constraint is $v=r\omega$, with $\omega$ the ball's spin angular velocity. The static contact friction does no work on the ball because the instantaneous contact point is stationary. Thus conservation of energy givesProject Newton's second law toward the hemisphere's centre. The inward component of gravity is $Mg\cos \theta$ and the normal force $N$ points outward, soAt contact loss $N=0$. Eliminating $v$ gives the ideal sphere rolling off a hemisphere resultThe radius cancels, so replacing $R+r$ by $R$ under the stated small-ball approximation leaves the same answer.

Finite-friction qualification. This is an ideal rolling-constraint result. It does not describe uninterrupted pure rolling to detachment with any finite coefficient of static friction. The tangential force and torque equations giveso $f=(2/7)Mg\sin \theta$ acts uphill, whereasConsequently the required ratio isFor a concrete example, a coefficient of static friction of one allows rolling only up to about $47.54^{\circ }$, where $17\cos \theta -10=2\sin \theta$, before sliding begins. A subsequent physical contact-loss angle needs a sliding-friction model. The boxed $53.97^{\circ }$ answers the source's expressly imposed no-slip idealization.

First test rest. With no other tangential forces, the required uphill static friction is $f_s=mg\sin \theta$. Its maximum is ${\mu }_{s}N$, where ${\mu }_s$ is the coefficient of static friction. ThusThe tangent function is increasing on this angle range, and its inverse tangent determines the last permitted resting angle ${\theta }_c$. At equality, the ideal model still permits limiting rest; a larger angle excludes it. Below the threshold, setting $f_s={\mu }_{s}N$ would incorrectly impose the maximum static friction even when less is required. Static friction on an inclined plane and inclined-plane measurement of static friction develop this onset criterion further.

For a block already sliding downhill, uphill kinetic friction has magnitude $f_k={\mu }_{k}N$, where ${\mu }_k$ is the coefficient of kinetic friction. Taking downhill as positive, Newton's second law becomesEvery term in the force balance scales with mass; division by $m>0$ removes it. Doubling mass doubles both gravitational weight and the contact forces, while leaving this acceleration unchanged if the coefficients remain unchanged. A mass-independent result is a prediction of these assumptions, rather than a universal property of every ramp.

For an original numerical model, stipulate $m=3\mathrm{kg}$, $g=9.8m/{\mathrm{s}}^2$, ${\mu }_s=0.45$ and ${\mu }_k=0.30$. The critical angle is ${\theta }_c\simeq 24.23^{\circ }$. At $20^{\circ }$, the normal force is $27.627\mathrm{N}$; rest requires $10.055\mathrm{N}$ of uphill static friction, below its $12.432\mathrm{N}$ bound. A resting block can stay there. If it is already sliding downhill, however, the kinetic friction is only $8.288\mathrm{N}$, giving downhill acceleration $a\simeq 0.5891m/{\mathrm{s}}^2$. Specifying the initial state matters.

At $30^{\circ }$, the downhill component of gravitational weight is $14.700\mathrm{N}$, while $N\simeq 25.461\mathrm{N}$ and the static friction bound is only $11.458\mathrm{N}$. Rest is impossible. During downhill sliding,Released from rest on a sufficiently long ramp, this ideal block covers its first $1.00\mathrm{m}$ in $t=\sqrt{2L/a}\simeq 0.9218\mathrm{s}$, reaching speed $v=\sqrt{2aL}\simeq 2.1697m/s$. As an independent energy calculation, the lost gravitational potential energy is $mgL\sin \theta =14.700\mathrm{J}$ and kinetic friction removes $f_{k}L\simeq 7.638\mathrm{J}$ of mechanical energy. The remaining $7.062\mathrm{J}$ equals $m{v}^2/2$ by the work-energy theorem.

At $\theta =\arctan {\mu }_k$, downhill sliding has zero acceleration and therefore constant velocity. Below that angle, a downhill-moving block slows; when it stops, test the static friction bound again. For uphill sliding, kinetic friction points downhill, so the signed downhill acceleration instead is $g(\sin \theta +{\mu }_k\cos \theta )$. The sign follows contact slip, and the downhill formula cannot be used unchanged after a reversal.

A uniform solid sphere released from the top of a fixed spherical surface has $v^2=10g(R+r)(1-\cos \theta )/7$ under the ideal rolling constraint. The normal force is $Mg(17\cos \theta -10)/7$, giving the title's ideal detachment angle. The required static friction is $2Mg\sin \theta /7$. Its ratio to the normal force diverges at detachment, so any finite coefficient of static friction causes prior slipping; a physical subsequent trajectory requires a sliding-friction model.

Static friction is the tangential contact force that maintains zero contact slip. “Static” describes the contact state: both surfaces can move together in the chosen inertial frame. In the ideal dry-contact model, the actual static friction adjusts to the equations of motion, subject to a bound, rather than always taking its maximum value.^[ref]Here $N$ is the magnitude of the normal force and ${\mu }_s$ the coefficient of static friction. Equality means limiting static friction; it is a threshold, not an instruction to replace every unknown contact force by ${\mu }_{s}N$.

For a stipulated example, place a nonrotating $2\mathrm{kg}$ block initially at rest on a stationary horizontal surface. Take gravitational acceleration $g=9.8m/{\mathrm{s}}^2$ and coefficient of static friction ${\mu }_s=0.40$, with no other vertical force. The vertical force balance gives $N=mg=19.6\mathrm{N}$, so the largest allowed static friction magnitude is $7.84\mathrm{N}$. Choose right as positive and apply a horizontal force $F$. Remaining at rest requires Newton's second law to giveAt $F=2\mathrm{N}$, the static friction is $-2\mathrm{N}$; at $F=6\mathrm{N}$, it is $-6\mathrm{N}$. Both states have zero acceleration. At $F=10\mathrm{N}$, balancing would require $f_s=-10\mathrm{N}$, outside the bound, so this initially resting block cannot remain at rest. Its subsequent acceleration requires a kinetic friction law; setting $f_s=-7.84\mathrm{N}$ after contact slip begins would still use the wrong contact state. At exactly $F=7.84\mathrm{N}$, the ideal inequality still permits rest at the threshold. These are model calculations, not measured material properties.

The toy model used in kinetic friction makes the contact-state distinction explicit: $m=1\mathrm{kg}$, $N=10\mathrm{N}$, ${\mu }_s=0.5$ and coefficient of kinetic friction ${\mu }_k=0.3$. On stationary ground, an initially resting box pushed right with $4\mathrm{N}$ has $f_s=-4\mathrm{N}$. At $6\mathrm{N}$ it cannot remain at rest; once it slides right, $f_k=-3\mathrm{N}$ and $a=3m/{\mathrm{s}}^2$. At $5\mathrm{N}$, rest is allowed with $f_s=-5\mathrm{N}$, whereas an already right-sliding box has $f_k=-3\mathrm{N}$ and $a=2m/{\mathrm{s}}^2$. The applied force alone does not specify the friction branch: contact slip and motion history matter.

For a flat contact with two tangential directions, the bound applies to a vector norm, not separately to each component:For the stipulated $7.84\mathrm{N}$ bound, balancing horizontal components $4\mathrm{N}$ and $4\mathrm{N}$ requires a force magnitude $\sqrt{32}\mathrm{N}\simeq 5.657\mathrm{N}$, which is allowed. Components $6\mathrm{N}$ and $6\mathrm{N}$ require $\sqrt{72}\mathrm{N}\simeq 8.485\mathrm{N}$, which is forbidden even though each component separately is below $7.84\mathrm{N}$. This circular bound assumes the same coefficient of static friction in every tangential direction. Near impending contact slip, the limiting static friction opposes the relative contact motion that would otherwise begin. Once actual contact slip exists, kinetic friction instead opposes its tangential relative velocity, which need not have the direction of the body's center of mass motion.

The normal force must also come from the equations of motion. On horizontal ground, an upward pull of magnitude $P$ at angle $\alpha$ above horizontal gives, for a block remaining at rest with no other forces,The sine component unloads the contact and the cosine component demands tangential support. These equations require $N>0$; if the supporting contact opens, this dry-contact model cannot supply a negative normal force. For the stipulated $2\mathrm{kg}$ block and $\alpha =30^{\circ }$, the positive threshold is $P={\mu }_{s}mg/(\cos \alpha +{\mu }_s\sin \alpha )\simeq 7.3544\mathrm{N}$, with $N\simeq 15.9228\mathrm{N}$ and $|f_s|\simeq 6.3691\mathrm{N}$. A downward pull increases $N$ instead. An inclined plane gives another reason why $N$ is not always $mg$.

To solve a new problem, impose zero contact slip, find the required static friction and normal force from the equations of motion, then check the bound. A demand inside it permits that contact state; a demand outside it rules the state out. For an ideal driven tire undergoing rolling without slipping on stationary ground, a forward static friction can accelerate the vehicle. Its role is to prevent contact slip, rather than to oppose all motion of the whole body.

Nor does the word “static” by itself make friction do zero work. The contact power delivered to a body is $P_s={\mathbf{f}}_s\cdot {\mathbf{v}}_c$, a dot product with its material contact-point velocity in the chosen inertial frame. At an ideal contact undergoing rolling without slipping on stationary ground, ${\mathbf{v}}_c=0$, so this power is zero. For a rigid body, adding the translational and rotational contributions gives ${\mathbf{f}}_s\cdot {\mathbf{V}}_{\mathrm{CM}}+{\mathbf{\tau }}_{\mathrm{CM}}\cdot \mathbf{\omega }={\mathbf{f}}_s\cdot {\mathbf{v}}_c$, where ${\mathbf{\tau }}_{\mathrm{CM}}$ is the contact torque about the center of mass and $\mathbf{\omega }$ its angular velocity. Counting only the first term omits the rotational contribution.

At a moving contact with zero contact slip, the two material contact points share a velocity ${\mathbf{v}}_c$ that can be nonzero. For instance, a nonrotating block moving with an accelerating belt receives positive contact power $f_{s}U$ when the belt's rightward velocity $U$ and rightward static friction $f_s$ are positive. The belt receives $-f_{s}U$ by Newton's third law. These contact contributions sum to zero in the ideal no-slip model, while the block's kinetic energy can increase. Zero contact slip and zero work on each body are different conditions.

An inclined plane tilted slowly from horizontal turns a coefficient of static friction into a critical angle. Assume a nonrotating block on a stationary, rigid, dry surface, with gravitational weight and the contact forces as its only forces. Take $0\le \theta <\pi /2$ to be the angle between the uphill surface direction and horizontal. Let ${\mathbf{e}}_t$ be a unit vector pointing uphill and ${\mathbf{e}}_n$ a perpendicular unit vector pointing outward from the surface. Resolving the gravitational weight givesThe angle between the downward vertical and the inward normal $-{\mathbf{e}}_n$ is also $\theta$. Thus the inward component uses cosine and the downhill component uses sine. These are components of one force, not two additional forces.

Before downhill contact slip, zero acceleration and Newton's second law requireThe required static friction points uphill. Substituting into the bound and dividing by the positive $mg\cos \theta$ givesThe tangent function increases on this range of angles, so the last admissible resting angle isThe inverse tangent takes a dimensionless quantity to an angle. At equality the ideal model still permits a limiting resting state; increasing $\theta$ further excludes it. At a smaller angle, $f_s/N=\tan \theta$ is the demand ratio, not the coefficient of static friction.^[ref]

For the stipulated $m=2\mathrm{kg}$, $g=9.8m/{\mathrm{s}}^2$ and ${\mu }_s=0.40$, the critical angle is approximately $21.8014^{\circ }$. At $\theta =15^{\circ }$, $N\simeq 18.932\mathrm{N}$ and $f_s\simeq 5.073\mathrm{N}$, comfortably below the bound ${\mu }_{s}N\simeq 7.573\mathrm{N}$. At $\theta =25^{\circ }$, maintaining rest would require $f_s\simeq 8.283\mathrm{N}$, but the bound is only $7.105\mathrm{N}$: rest is impossible. At ${\theta }_c$, $N\simeq 18.198\mathrm{N}$ and $f_s\simeq 7.279\mathrm{N}$. Notice that the limiting tangential force here is smaller than the horizontal $7.84\mathrm{N}$ limit because tilting reduces the normal force.

Cancellation of mass makes this relation useful: the ideal critical angle tests a contact coefficient without needing a calibrated force gauge. Doubling the block's mass doubles both demanded static friction and its bound, leaving ${\theta }_c$ unchanged if ${\mu }_s$ is unchanged. This is a testable model prediction. It need not survive a change in surface condition, a direction-dependent coefficient, appreciable deformation, or vibration.

The derivation also assumes continued contact and that sliding occurs before tipping or rolling without slipping. The resultant contact force must act within the supporting footprint so that the block can satisfy torque balance; a tall block may tip first. No extra tension, imposed tangential pull, or lift is included. In a slowly raised apparatus, quasistatic process means that motion of the board contributes negligible inertial forces while locating the threshold. Once downhill contact slip begins, a constant-velocity sliding angle would concern kinetic friction, not the onset of static friction.