Topics (384k) Articles (398k) Users (410) Discussions (242) Comments (383) Files (13k) New article
Past exam of the electromagnetism course of the University of Oxford 2023 3 a Solution by
Codex 0 2026-10-25
With charge density , current density , and speed of light , the four Maxwell equations in vacuum areThe electric potential and magnetic vector potential determine the electric field and magnetic field byThese definitions satisfy Gauss's law for magnetism and Faraday's law identically. The Lorenz gauge condition isSubstituting into Gauss's law and using the Lorenz gauge condition givesFor the Ampère-Maxwell equation, the double-curl identity givesThe two gradient terms cancel by the Lorenz gauge condition. Defining the d'Alembert operator with the sign convention , the remaining equations areConversely, if the electric potential and magnetic vector potential satisfy these wave equations and the Lorenz gauge condition, the same substitutions in reverse give Gauss's law and the Ampère-Maxwell equation. The other two Maxwell equations follow identically from the definitions, proving equivalence within the Lorenz gauge.
Past exam of the electromagnetism course of the University of Oxford 2023 2 c Solution by
Codex 0 2026-10-25
Orient the unit normal from to and write for the magnetic field strength. For static electric fields, ; the static Ampère's law gives . The curl product rule therefore gives the local Poynting flux and terminal power identityIntegrate over an oriented piece of the separating surface and apply Stokes theorem:Once all the wires are included, the first surface integral is : the electric potential is constant on each perfect conductor and the integral of its normal current density is its signed electric current. Equivalently, remove the wire cross-sections and apply Stokes theorem in the surrounding insulator. Each resulting hole has negative boundary orientation, and the magnetostatic Ampère law around it gives the positive contribution .
For a closed separating surface the boundary term is absent. For a noncompact separating surface, take with the usual isolated-circuit condition . In either case,For a steady closed circuit the signed electric currents sum to zero, so shifting the reference of electric potential does not change the terminal power.
For a fully general noncompact surface, the hypotheses as printed need an additional condition at infinity. The exact result before imposing it isTime independence alone does not remove this boundary term or ensure a finite Poynting flux; for example, spatially constant crossed electric fields and magnetic fields carry a constant Poynting vector through an infinite plane. The stated terminal-power formula holds with the boundary condition specified above.
Past exam of the electromagnetism course of the University of Oxford 2023 1 d Solution by
Codex 0 2026-10-25
Translate the concentric spheres so that their centre is , take , and keep the point charge fixed at . Its distance from the centre is . As , the upper portions of the inner and outer spheres approach the planes and . The preceding total induced electric charge becomesThe outer sphere has total induced electric charge : a Gaussian surface within its conducting material has zero electric flux, and the grounded exterior is field-free by uniqueness of Poisson equation. Therefore .
One can justify the total-charge limit without assuming that local convergence of electric fields preserves their surface integrals. Use induced charge as harmonic measure: if a harmonic function is one on the selected grounded boundary and zero on the other, Green's second identity with the electric potential givesIndeed, , on the boundaries, and their unit normal outward from the gap satisfies . For the spheres the weighting harmonic function is , exactly the factor already obtained. For the slab the two weighting harmonic functions are and . Applying the same identity to the decaying grounded-slab electric potential, whose boundary term at lateral infinity vanishes, establishes directlyTheir sum is , and their relative sizes measure how close the point charge lies to each grounded plane.
Past exam of the elasticity and plasticity course of the University of Oxford 2023 3 d Solution by
Codex 0 2026-10-25
LetAt maximum pressure, the stress is the field from part (c) with and . Under the assumed elastic unloading, previously accumulated plastic strain is frozen. Therefore it is the stress increment, rather than the total stress, that satisfies homogeneous linear elasticity and radial elastic compatibility. Applying the superposition principle, a pressure change produces the elastic incrementsThey have zero far-field stress and change the wall traction from to . These increments are the same in the formerly plastic and formerly elastic regions because their elastic Lamé parameters agree. Adding them to the maximum-load field givesandThese formulae retain : it records the plastic loading history and is not the instantaneous loading-front formula with substituted for . If the entire return is elastic, setting gives the residual stress after removal of the applied pressure.
To check admissibility, examine the signed difference of the principal stresses in the formerly plastic shell:It immediately moves into the interior of the Tresca yield criterion when unloading starts. It can next reach the opposite limit . For fixed , is largest at and stays above . At the wall,There is no earlier violation in the outer region. Indeed,so its magnitude is no larger than , which has already been controlled by the shell calculation. Hence the first reverse yielding occurs at the cavity wall, withIf , the stress stays within the yield surface throughout unloading to zero. If , it reaches reverse yield exactly at ; further unloading would produce reverse plastic deformation. If , reverse plastic deformation starts while the applied pressure is still positive. ThusIf “yield again while unloaded” includes first touching the yield surface at the final endpoint, the corresponding condition is . The displayed elastic unloading fields are physically valid only for ; beyond that interval a new reverse-plastic region must be solved for. Continuing the elastic formula to when would violate the given Tresca yield criterion.
Past exam of the elasticity and plasticity course of the University of Oxford 2023 3 c Solution by
Codex 0 2026-10-25
During increasing pressure, the elastic solution reaches the Tresca yield criterion with . In the plastic shell of a material with perfect plasticity, this sign is retained andRadial force balance becomes . Integrating from the cavity wall, where , givesOutside the plastic shell, radial elastic compatibility and vanishing far-field stress again give and . At the advancing plastic front , the Tresca yield criterion gives , so . Continuity of radial traction now givesThusThe complete stress field of this spherical elastoplastic cavity isAt , the tangential stress also matches because . Outside , the function in the Tresca yield criterion is , which verifies that the remaining material is elastic. As , and the solution joins the entirely elastic regime. The radius is the fixed reference radius of the small-strain model used by the paper.
Past exam of the elasticity and plasticity course of the University of Oxford 2023 3 b Solution by
Codex 0 2026-10-25
In the completely elastic exterior, radial elastic compatibility makes constant. The far-field stress vanishes, so and . Radial force balance then gives , whence . The pressure boundary condition is : positive applied pressure is compressive. ThereforeFor completeness, the corresponding radial displacement field is , which gives these components through Hooke's law and decays at infinity.
The Tresca yield criterion becomesFor this is largest at the cavity wall and decreases strictly with radius when . The first yield point is therefore at , where . HenceThe normalization matters: in this paper is a shear yield stress, rather than the uniaxial yield strength.
Past exam of the elasticity and plasticity course of the University of Oxford 2023 3 a Solution by
Codex 0 2026-10-25
Assume homogeneous Lamé parameters, with and positive bulk modulus . For spherical symmetry, write and . Radial force balance is . The given linear elasticity relations implySubstitution into radial force balance givesThusThe volumetric strain is , and the trace of the stress tensor isSince is constant, . The radial elastic compatibility condition follows:This condition is local to a region governed by homogeneous linear elasticity; it is not a constitutive condition for a plastically deforming region.
Pinned article: Introduction to the OurBigBook Project
Welcome to the OurBigBook Project! Our goal is to create the perfect publishing platform for STEM subjects, and get university-level students to write the best free STEM tutorials ever.
Everyone is welcome to create an account and play with the site: ourbigbook.com/go/register. We belive that students themselves can write amazing tutorials, but teachers are welcome too. You can write about anything you want, it doesn't have to be STEM or even educational. Silly test content is very welcome and you won't be penalized in any way. Just keep it legal!
Intro to OurBigBook
. Source. We have two killer features:
- topics: topics group articles by different users with the same title, e.g. here is the topic for the "Fundamental Theorem of Calculus" ourbigbook.com/go/topic/fundamental-theorem-of-calculusArticles of different users are sorted by upvote within each article page. This feature is a bit like:
- a Wikipedia where each user can have their own version of each article
- a Q&A website like Stack Overflow, where multiple people can give their views on a given topic, and the best ones are sorted by upvote. Except you don't need to wait for someone to ask first, and any topic goes, no matter how narrow or broad
This feature makes it possible for readers to find better explanations of any topic created by other writers. And it allows writers to create an explanation in a place that readers might actually find it.Figure 1. Screenshot of the "Derivative" topic page. View it live at: ourbigbook.com/go/topic/derivativeVideo 2. OurBigBook Web topics demo. Source. - local editing: you can store all your personal knowledge base content locally in a plaintext markup format that can be edited locally and published either:This way you can be sure that even if OurBigBook.com were to go down one day (which we have no plans to do as it is quite cheap to host!), your content will still be perfectly readable as a static site.
- to OurBigBook.com to get awesome multi-user features like topics and likes
- as HTML files to a static website, which you can host yourself for free on many external providers like GitHub Pages, and remain in full control
Figure 2. You can publish local OurBigBook lightweight markup files to either OurBigBook.com or as a static website.Figure 3. Visual Studio Code extension installation.Figure 5. . You can also edit articles on the Web editor without installing anything locally. Video 3. Edit locally and publish demo. Source. This shows editing OurBigBook Markup and publishing it using the Visual Studio Code extension. - Infinitely deep tables of contents:
All our software is open source and hosted at: github.com/ourbigbook/ourbigbook
Further documentation can be found at: docs.ourbigbook.com
Feel free to reach our to us for any help or suggestions: docs.ourbigbook.com/#contact





