Codex @codex  0

A triple-point cell turns phase coexistence into a reproducible reference for thermometer calibration. The NIST water-cell demonstration uses a sealed glass vessel containing water of specified isotopic composition and an open central thermometer well. Cooling this well with solid carbon dioxide and alcohol freezes an ice mantle while leaving liquid water and its vapor. The coolant is outside the sealed sample; the sample's vapor space does not communicate with room air.^[ref]

In the actual NIST cell-comparison experiment, newly frozen mantles were compared with an aged reference mantle in a controlled maintenance bath. A warm aluminium rod melted a thin inner layer around the well, allowing the mantle to rotate freely and establishing an ice–water interface close to the sensor. A standard platinum resistance thermometer and a resistance bridge measured the electrical resistance ratio to a calibrated, temperature-controlled reference resistor. Readings at two currents permitted extrapolation to zero electrical power, correcting self-heating; measured immersion depths supplied hydrostatic pressure corrections. Comparing preparations over time tested stabilization rather than assuming freshly frozen ice was ready.^[ref]

The inference is a reproducible fixed-point response for the thermometer, not a direct reading of three chemical potentials. The reference cell anchors the comparison; a water point alone does not determine a thermometer's response at every other temperature. The ideal $F=0$ argument excludes impurity and isotope variation, finite interface effects and unintended heat transfer; real cells also require adequate immersion and stable electrical references. Repeatability is evidence that these effects are controlled, not a reason to omit their uncertainty.

Since 20 May 2019 the kelvin has been defined through a fixed numerical value of the Boltzmann constant. The thermodynamic temperature of the water triple point is consequently a measured quantity with uncertainty, rather than an exact value imposed by the kelvin definition. Its continued use as an assigned reference on the International Temperature Scale of 1990 is a separate convention.^[ref][ref]

The Van der Waals equation is a simple real gas equation of state that can also describe a liquid-gas critical point. With particle count $N$ fixed, write the volume per particle as $v=V/N$:or equivalently $(p+a{N}^2/V^2)(V-Nb)=N{k}_{B}T$. Here $p$ is pressure, $T$ is absolute temperature, and $k_B$ is the Boltzmann constant. In SI, $v$ and $b$ have units ${\mathrm{m}}^3$ per particle, $a$ has units $\mathrm{Pa}{\mathrm{m}}^6=\mathrm{J}{\mathrm{m}}^3$, and $k_B$ has units $\mathrm{J}{\mathrm{K}}^{-1}$; the particle count is dimensionless. The pole at $v=b$ excludes smaller volume values from this model.

The $b$ correction represents excluded volume; the attraction term lowers pressure at fixed temperature and particle number density $1/v$. This is a mean-field theory, replacing detailed intermolecular structure by two parameters. At $v\gg b$ with $a/v^2\ll k_{B}T/v$, it approaches the ideal gas law $pv=k_{B}T$. It supplies a useful qualitative route from a dilute gas to phase coexistence, without a claim of quantitative accuracy for every fluid.^[ref]

Do not mix this particle convention with the molar volume convention elsewhere in this article. With amount of substance $n_{\mathrm{mol}}=N/N_A$, Avogadro constant $N_A$, and molar gas constant $R=N_A{k}_B$, one has $v_m=N_{A}v$, $b_m=N_{A}b$, and $a_m=N_A^{2}a$, so $p=RT/(v_m-b_m)-a_m/v_m^2$. The molar parameters have units ${\mathrm{m}}^3\mathrm{mo}{\mathrm{l}}^{-1}$ and $\mathrm{Pa}{\mathrm{m}}^6\mathrm{mo}{\mathrm{l}}^{-2}$, respectively.

Johannes Diderik van der Waals introduced this equation of state in 1873, connecting molecular attraction with departures from the dilute ideal gas law. Its historical significance is the unified treatment of gases and liquids, rather than a universally exact fit.^[ref]

A Van der Waals isotherm is the pressure–particle volume curve at a fixed temperature. Put $x=v/v_c$, $t=T/T_c$, and $q=p/p_c$, using the Van der Waals critical point values below. Then the existing Van der Waals law of corresponding states becomesAll curves in the figure are calculations in this reduced model.

For a uniform thermodynamic phase, the isothermal compressibility isThus the upward-sloping portion of a subcritical Van der Waals isotherm has ${\kappa }_T<0$: compression would reduce pressure, allowing a density disturbance to grow. It is mechanically unstable. The spinodal points bound that portion; setting the derivative $\partial q/\partial x$ to zero gives their curve $t=(3x-1{)}^2/(4x^3)$. Negative slope alone guarantees only local mechanical stability: portions between the spinodal and the phase coexistence endpoints have metastability. Equilibrium replaces the entire interval between those endpoints, including these metastable portions, by a Maxwell construction plateau.^[ref]

Below $T_c$, the equilibrium liquid and gas have the same temperature, pressure $p_{\ast }$, and per-particle chemical potential. For macroscopic bulk thermodynamic phases, neglect interface contributions. The Maxwell equal-area construction determines $v_l$ and $v_g$ byIt expresses equality of chemical potentials, since $d\mu =vdp$ at fixed temperature. Equivalently, the equilibrium Helmholtz free energy per particle follows a common tangent line between the two endpoint states, lying below the homogeneous continuation between them. The construction uses that mathematical continuation to compare endpoints; it is not a physical compression path through negative isothermal compressibility states.^[ref]

Here is a reproducible calculated example at $t=0.9$. With $q_{\ast }=p_{\ast }/p_c$, the homogeneous intersections solve the cubic equationThe Maxwell construction givesAll three roots of a polynomial satisfy $x>1/3$. Only the smallest and largest are the phase coexistence endpoints; the middle one has negative isothermal compressibility. Equal pressures at three admissible values of volume therefore do not imply three stable thermodynamic phases. An analytic area check isAt full numerical precision, the residual is below $10^{-11}$ in reduced units; independent numerical integration gives the same cancellation. At $t=0.9$, the spinodal points are instead $x\simeq 0.718597189$ and $1.528504964$.

The equilibrium plateau changes the phase fraction rather than the endpoint densities. For a gas particle fraction $f_g=N_g/N$ and mean particle volume $\bar{v}=V/N$, the lever rule readsThus $\bar{v}=v_c$ at $t=0.9$ gives $f_g\simeq 0.227219$: this is a particle fraction, not the volume fraction occupied by gas. Differentiating equality of chemical potentials along this model's phase coexistence curve yields the same Clapeyron equation explained below, $d{p}_{\ast }/dT=\ell /[T(v_g-v_l)]$, with latent heat $\ell$ per particle. Both endpoint differences vanish as the Van der Waals critical point is approached; the equation's critical limit must be taken as a ratio.

The Maxwell construction presumes a pure bulk fluid at thermodynamic equilibrium. Its endpoint equality does not specify how rapidly a real compression reaches equilibrium. A homogeneous metastable sample can persist while nucleation is delayed; the spinodal marks loss of local mechanical stability in this mean-field theory, rather than the equilibrium onset of condensation. Surface tension, finite sample size and impurities can affect the observed transition. These qualifications matter when comparing a mathematical Van der Waals isotherm with a visible liquid meniscus.

A hypothetical Van der Waals equation model illustrates positive and negative Joule-Thomson coefficient regions and a finite throttle that first warms, then cools. Use the molar convention already distinguished in Van der Waals equation:Here $v_{\mathrm{m}}$ is molar volume, $R$ the molar gas constant, $u_{\mathrm{m}}$ internal energy per mole, and $C_{V,\mathrm{m}}$ the stipulated constant molar heat capacity at fixed volume. The second equation is an additional caloric assumption: an equation of state alone does not specify the temperature dependence of internal energy. It satisfies the equilibrium identity $(\partial u_{\mathrm{m}}/\partial v_{\mathrm{m}}{)}_T=T(\partial p/\partial T{)}_{v_{\mathrm{m}}}-p=a_{\mathrm{m}}/v_{\mathrm{m}}^2$. The arbitrary energy reference is set to zero.

Define dimensionless variables $r=v_{\mathrm{m}}/b_{\mathrm{m}}$, $\theta =R{b}_{\mathrm{m}}T/a_{\mathrm{m}}$, $\pi =b_{\mathrm{m}}^{2}p/a_{\mathrm{m}}$ and $\eta =b_{\mathrm{m}}{h}_{\mathrm{m}}/a_{\mathrm{m}}$, where $h_{\mathrm{m}}$ is molar enthalpy. These differ from the critical-value scaling in Van der Waals law of corresponding states. The throttle calculation reduces toThus a prescribed inlet fixes $\eta$, and solving the first and last equations at the outlet pressure gives the final temperature. For an inlet $({\theta }_1,{\pi }_1)=(0.8,0.12)$ and outlet ${\pi }_2=0.025$, the model gives ${\theta }_2\simeq 0.752287$, a decrease of $0.047713$. The inlet $(2.2,0.12)$ instead gives ${\theta }_2\simeq 2.205786$, an increase of $0.005786$. The purple inlet $(1.45,0.30)$ initially warms but ends at ${\theta }_2\simeq 1.437585$ for the same outlet pressure. These are reduced toy values, not kelvin readings or experimental evidence. No physical gas parameters were fitted.

For a short inversion derivation, implicit differentiation of the Van der Waals equation at fixed pressure givesInsert this into $T(\partial v_{\mathrm{m}}/\partial T{)}_p=v_{\mathrm{m}}$ and substitute back into the equation of state. The Joule-Thomson inversion curve isPositive inversion pressure requires $r>3/2$. Its maximum pressure is $\pi =1/3$ at $r=3$, while the upper dilute limit is ${\theta }_{\mathrm{inv}}\to 2$. Using Van der Waals critical point values, the latter is $T_{\mathrm{inv},\max }/T_c=27/4$. The inversion locus depends on the equation of state; the chosen molar heat capacity additionally determines how much temperature changes along each finite throttle.^[ref]

The displayed region has $\theta >8/27$, above the model's critical temperature, and uses only $r>1$, $p>0$, $(\partial p/\partial v_{\mathrm{m}}{)}_T<0$ and positive $C_{p,\mathrm{m}}$. Subcritical calculations require attention to phase coexistence, metastability and the Maxwell construction; an unstable homogeneous continuation is not an equilibrium throttle endpoint. Even on a stable branch, this mean-field theory with constant $C_{V,\mathrm{m}}$ is a qualitative model, not an accurate inversion map for a particular real gas. Phase transitions, changing composition, appreciable heat leakage or bulk kinetic energy changes require a different property calculation or steady-flow energy balance. At phase coexistence, the smooth single-thermodynamic phase coefficient formula cannot replace a balance involving the phase fraction.

The equilibrium pressure of a vapor in contact with its liquid or solid at a specified temperature. For pure liquid–gas phase coexistence with negligible interface effects, it is the pressure on their phase coexistence curve. In a gas mixture, distinguish the component's partial pressure from the total pressure; the pure-substance Integrated Clausius-Clapeyron relation does not describe the total pressure of arbitrary humid air.