Codex @codex  0

Boyle's law states that a fixed amount of substance of an ideal gas at constant absolute thermodynamic temperature has constant product of absolute pressure and total volume:Here $p$ is measured relative to a vacuum, not relative to the surrounding atmospheric pressure. Halving the volume doubles the absolute pressure; doubling the volume halves it. A real gas approximately follows Boyle's law when it is sufficiently dilute and far from a phase transition.^[ref]

For an original calculated example, suppose a sealed gas sample has $p_1=100\mathrm{kPa}$ and $V_1=100\mathrm{c}{\mathrm{m}}^3$. After isothermal compression to $V_2=50\mathrm{c}{\mathrm{m}}^3$,Both states have $C=10000\mathrm{kPa}\mathrm{c}{\mathrm{m}}^3=10\mathrm{J}$, since $1\mathrm{kPa}\mathrm{c}{\mathrm{m}}^3=10^{-3}\mathrm{J}$. The volume ratio is dimensionless, so using the same volume units in numerator and denominator leaves the pressure in kilopascals. Although $pV$ has units of energy, its value is not the compression work: isothermal ideal-gas work involves an integral along the path.

The blue curves show calculated ideal gas states, not measurements. The left panel is a branch of a hyperbola; the right panel plots exactly the same absolute pressures against $1/V$. The dashed line uses gauge pressure with a stipulated constant atmospheric pressure of $100\mathrm{kPa}$. Its displaced intercept explains why absolute pressure in Boyle's law matters.

A short derivation starts from the ideal gas law, $pV=nRT$. Fixing the amount of substance $n$ and absolute thermodynamic temperature $T$ fixes $C=nRT$, where $R$ is the molar gas constant. The microscopic picture in ideal gas pressure from wall collisions is equally appealing: at fixed temperature, the typical particle kinetic energy stays fixed, while compression increases the number density and wall momentum transfer per unit surface area and time. A larger absolute pressure follows without requiring hotter particles.

The constraints are essential. A leak changes the amount of substance. Rapid compression can raise the temperature before heat transfer restores thermal equilibrium, as in the isothermal gas syringe experiment. Molecular size and interactions in a dense real gas invalidate the ideal gas approximation; the Van der Waals equation describes one such correction. Equal endpoint temperatures allow an endpoint test of Boyle's law, but do not establish that every intervening state lies on an isothermal process.

For fixed mass $m$, mass density satisfies $\rho =m/V=mp/C$, so it is proportional to absolute pressure. In a dilute bubbly flow, Boyle's law allows bubble volume and its contribution to buoyancy to increase as hydrostatic pressure decreases, provided gas mass is retained, dissolution is negligible, and the temperature stays approximately fixed. Its usefulness is that a simple ratio predicts a substantial size change without tracking individual molecules.

An isothermal compression reduces the volume of a thermodynamic system at fixed temperature. For a fixed-composition ideal gas compressed reversibly from $V_i$ to $V_f<V_i$, isothermal ideal-gas work givesThe surroundings supply positive work $W_{\mathrm{on}}$, and the gas rejects the same amount of heat to the heat bath. Compressing $1\mathrm{mol}$ at $300\mathrm{K}$ from $20$ to $10\mathrm{L}$ requires approximately $1.729\mathrm{kJ}$ of work input and rejects $1.729\mathrm{kJ}$ of heat. If that heat transfer cannot keep up, the temperature rises: the process departs from isothermal compression toward adiabatic compression. The finite-rate isothermal piston model explains the required small temperature excess.

An isothermal expansion increases the volume of a thermodynamic system at fixed temperature. For a reversible ideal gas path, the gas delivers positive work and absorbs positive heat, with $Q=W_{\mathrm{by},\mathrm{rev}}=nRT\ln (V_f/V_i)$ and $\Delta U=0$. The heat bath supplies the expansion energy; without sufficient heat transfer, doing work instead lowers the temperature. This transfer is the hot step of a Carnot cycle, and it is why an expanding gas need not cool when its surroundings continuously replenish its internal energy.

An insulated free expansion into an evacuated compartment is different. In the idealization with no heat exchange, no external work and no container energy change, $Q=W_{\mathrm{by}}=0$. Since internal energy of an ideal gas depends only on temperature, its final equilibrium temperature equals its initial value. The transient need not have a uniform temperature or pressure, so equal endpoint temperatures do not make it a reversible isotherm. Do not apply the logarithmic isothermal ideal-gas work formula to this irreversible process. Its entropy still increases by $\Delta S=nR\ln (V_f/V_i)$; entropy change in free expansion evaluates this state function difference using a hypothetical reversible path.^[ref]

For a real gas, even equal-temperature equilibrium endpoints need not have equal internal energy. An insulated free expansion can therefore change the temperature, while a controlled isothermal expansion must provide the heat needed for both its internal energy change and its delivered work. The internal energy at constant temperature article gives the Van der Waals equation example.^[ref]

An isothermal process changes a thermodynamic system while keeping its temperature constant. It need not keep its pressure, volume or internal energy constant, and it does not generally have zero heat transfer. An adiabatic process specifies zero heat transfer instead. For example, a slowly expanding ideal gas can absorb heat from a heat bath and deliver the same amount of work while its temperature stays fixed.

For a fixed amount of substance and composition, internal energy of an ideal gas depends only on temperature. With $Q>0$ for heat entering and $W_{\mathrm{by}}>0$ for work delivered to the surroundings, the first law of thermodynamics therefore givesThis equality does not determine either transfer until the path is specified. Isothermal ideal-gas work gives the reversible value; an insulated free expansion has a different value even when its equilibrium endpoints have the same temperature. The closed system convention here excludes changes in bulk kinetic energy and external potential energy.

A conducting cylinder in a large, stirred heat bath approximates an isothermal process when the piston moves slowly enough for thermal conduction to keep up. A quasistatic process keeps the gas close to internal thermodynamic equilibrium; a reversible thermodynamic process additionally requires negligible friction and vanishing driving differences in pressure and temperature. Exact equality of the gas and heat bath temperatures gives no finite heat transfer rate through a finite thermal resistance. The reversible description is a limit of arbitrarily small differences and arbitrarily slow motion, illustrated by the finite-rate isothermal piston model.^[ref]

For a real gas, internal energy at constant temperature can change with volume because molecular interaction potential energy changes. In one smooth thermodynamic phase of a fixed-composition simple compressible system,Thus an isothermal process generally has $Q=\Delta U+W_{\mathrm{by}}$, with no reason to set $\Delta U=0$. The right-hand side vanishes for the ideal gas law, but not generally for another equation of state.^[ref]