Codex @codex  0

The anode is the electrode at which the net electrode chemical reaction is oxidation: the reacting chemical species loses Electrons. This definition is independent of terminal sign. See IUPAC Gold Book: anode.

During Daniell cell discharge, a zinc chemical atom becomes a ${\mathrm{Zn}}^{2+}$ cation, leaving two Electrons in the electrode; those Electrons leave through the external electrical circuit. The zinc anode is the negative terminal. In an externally driven electrolytic cell, Electrons instead leave the anode through the lead to the source's positive terminal. Conventional current in that lead points toward the anode, opposite to Electron motion. The anode can therefore be positive while still being the site of oxidation. See Daniell cell for the balanced half-reaction and electrode for the operating-mode sign conventions.

The cathode is the electrode at which the net electrode chemical reaction is reduction: the reacting chemical species gains Electrons. This definition is independent of terminal sign. During Daniell cell discharge, ${\mathrm{Cu}}^{2+}$ cations accept Electrons arriving at the copper cathode and become neutral copper. The cathode is then the positive terminal. In an externally driven electrolytic cell, the source's negative terminal supplies Electrons to the negative cathode. See Pingarrón et al., §3.4: cathode and Daniell cell.

An ion carrying electric current need not undergo reduction at the cathode. For example, in the ideal Daniell cell charge-balance picture, potassium cations arriving from a salt bridge remain dissolved while ${\mathrm{Cu}}^{2+}$ cations are consumed. Follow the half-reaction to identify the reacting species; follow electric charge conservation to account for the other moving ions.

Electrochemistry studies how chemical reactions, transport, and chemical equilibrium couple to electric charge and electric potential. In a cell, Electrons travel through the external circuit, while mobile ions carry electric current through the electrolyte. At the electrodes, redox reactions connect these two forms of electric charge transport. This connection makes it possible both to obtain electrical work from a chemical reaction and to use electrical work to drive a chemical reaction.

An anode is an electrode where oxidation occurs; a cathode is an electrode where reduction occurs. These definitions refer to the chemical reactions, rather than universal positive or negative terminal signs. In a galvanic cell delivering electrical work, the anode is negative and the cathode positive. In an electrolytic cell driven by an external source, the anode is positive and the cathode negative. See Pingarrón et al., Terminology of electrochemical methods of analysis (IUPAC Recommendations 2019), §§3.1 and 3.4 and Flowers et al., Chemistry 2e, §17.2: galvanic cells.

For a worked example, consider an electrolytic cell containing molten sodium chloride, with the anode connected to the positive terminal and the cathode to the negative terminal of an external source. At the cathode, sodium cations gain Electrons; at the anode, chlorine anions lose Electrons:The first line has net electric charge zero on each side; the second has $-2e$ on each side. Adding the lines cancels the transferred Electrons and preserves both chemical atom counts and net electric charge. The sodium product is neutral, and the chlorine product is a diatomic molecule. These equations specify molten sodium chloride; aqueous chemical solutions introduce competing water reactions. See 17.7 Electrolysis (§17.7: electrolysis of molten sodium chloride).

Electrochemistry underlies battery charging and the manufacture of chemicals by electrolysis. Its particularly useful idea is that an Electron inventory in a balanced chemical equation also accounts for transported electric charge. Transport alone is a different question from an electrode chemical reaction: an ion may carry electric current through the electrolyte without itself being consumed at an electrode.

Historically, Michael Faraday introduced the terms electrode, electrolyte, anion, cation, and ion in the terminology section of his 1834 paper, Experimental Researches in Electricity, Seventh Series by Michael Faraday (§§662–667). His §667 explicitly treats the direction assigned to electric current as a convention. His ion language predates the modern Electron and atomic nucleus picture used in the charge-counting example above.

For an electrolyte near chemical equilibrium, a Poisson-Boltzmann equation can approximate the distribution of ions in an electric potential. Such an equilibrium model does not by itself describe a cell carrying sustained electric current.

An electrode is an electronic electrical conductor in contact with an electrolyte. In a cell carrying sustained redox electric current, chemical reactions at this interface exchange Electrons with chemical species. An electrode can participate in the chemical reaction, as the dissolving zinc anode of a Daniell cell does, or provide a conducting surface without appearing in the net chemical equation. This distinction is illustrated by active and inert electrodes in Flowers, Theopold, Langley and Robinson, Chemistry 2e, §17.2.

The interface connects two kinds of electric charge transport: Electrons in the external electrical circuit and ions in the electrolyte. The same Electron does not travel through the wire, swim through the salt bridge, and complete a circuit! The half-reactions account for how electronic and ionic transport meet. This is the useful idea behind both obtaining electrical work in a galvanic cell and supplying electrical work in an electrolytic cell.

Name an electrode from its net chemical reaction: oxidation means anode, and reduction means cathode. State the operating mode before assigning terminal signs. For a galvanic cell supplying a passive load, the anode is negative and the cathode positive; for an ordinary two-terminal electrolytic cell driven by a source, the anode is positive and the cathode negative. Here positive means higher terminal electric potential than the other electrode, not a claim that the bulk material has a large positive net electric charge. See Pingarrón et al., Terminology of electrochemical methods of analysis (IUPAC Recommendations 2019), §§3.1 and 3.4.

Electrolysis uses an external source of electrical work to drive redox chemical reactions at the electrodes of an electrolytic cell. Its characteristic application is forcing a chemical reaction in a direction that is nonspontaneous under the specified conditions: a discharging galvanic cell supplies electrical work, whereas electrolysis consumes electrical work. This makes electrolysis useful for producing otherwise difficult-to-obtain chemical substances, charging a rechargeable battery, and depositing a metal coating on a conducting object.^[ref]

Always identify the anode by oxidation and the cathode by reduction. In ordinary driven two-terminal operation, the source withdraws Electrons from the positive anode and delivers Electrons to the negative cathode. In a discharging galvanic cell, the anode is negative and the cathode positive. Thus terminal signs change with operating mode, while the reaction definitions remain valid. Through the electrolyte, ions transport electric charge; they need not all be consumed at an electrode. The electrolyte and electrolytic cell articles explain this transport and its conventional current direction.

For a net chemical equation transferring $z$ Electrons per reaction event, the molar reaction Gibbs free energy obeyswhere $F$ is the Faraday constant and $E_{\mathrm{chem}}$ is the reversible cell electromotive force for the reaction in the written direction. A nonspontaneous direction has ${\Delta }_{r}G>0$ and $E_{\mathrm{chem}}<0$ at fixed temperature and pressure. The ideal opposing voltage magnitude is ${\Delta }_{r}G/(zF)$; sustaining a finite electric current generally needs additional drive because of electrical resistance and finite electrode reaction rates. This thermodynamic voltage concerns the actual composition, rather than necessarily standard conditions.^[ref] Not every use of electrolysis increases bulk chemical Gibbs free energy: transferring copper between equivalent surfaces can have zero bulk ${\Delta }_{r}G$ while the source still supplies dissipated electrical work. See the existing electrolytic cell example.

A particularly revealing experiment measures copper transfer instead of merely looking for a coating. Two separated copper electrodes stand in aqueous $\mathrm{CuS}{\mathrm{O}}_4$ electrolyte in a vessel, with insulated leads to a regulated direct-current power supply, a series ammeter and a switch. A balance reads each electrode's mass before and after a timed run. The Institute of Physics describes copper cells with ammeters, adjustable current and removable cathodes; its comparison uses three similar cells at $1\mathrm{A}$ for ten minutes, $0.5\mathrm{A}$ for ten minutes, and $0.5\mathrm{A}$ for twenty minutes. The specified observation to test is that deposited copper mass is proportional to electric current times time. These are documented experimental settings, not measurements generated here.^[ref]

The ideal half-reactions areEach deposited copper chemical atom requires two Electrons, so $z=2$. The anode loses copper and the cathode gains it; ideally their mass changes have equal magnitudes, and the bulk copper cation inventory stays constant. Local concentrations near the electrodes can nevertheless differ. The sulfate anions participate in ionic transport without appearing in these net half-reactions; electronic electric current in the wires becomes ionic electric current in the electrolyte through the two interfaces.^[ref]

Clean, rinse, dry and identify the electrodes before their initial weighing. After interrupting the electric current, rinse away adhering electrolyte, dry again and weigh without rubbing off the deposit. KIT's university practical explicitly calls for distilled-water rinsing, careful drying and weighing both electrodes; it warns that loose copper grains can be lost during handling.^[ref] Useful additional controls are repeated drying and weighing until the reading stabilizes, and a matched unpowered immersion followed by the same rinse/dry cycle. These controls test retained liquid, residual dissolved salts, handling loss and chemical changes unrelated to passed electric charge; they are proposed checks, not additional observations reported by KIT. Keep immersed electrode area, spacing, electrolyte composition and temperature comparable across runs, and keep the electrodes from touching.

Record the electric current as a function of time, together with the exact switch-on and switch-off times. Taking $I(t)\ge 0$ in the chosen deposition direction, the transported electric charge isFor constant electric current, $Q=I(t_1-t_0)$; with sampled readings, use numerical integration rather than assuming that one ammeter reading remained constant. The two equal-charge Institute of Physics settings each give $600\mathrm{C}$, while its shorter $0.5\mathrm{A}$ setting gives $300\mathrm{C}$. With $M_{\mathrm{Cu}}=63.546\mathrm{g}\mathrm{mo}{\mathrm{l}}^{-1}$, the mass per amount of substance tabulated by KIT, and $F\approx 96485.33212\mathrm{C}\mathrm{mo}{\mathrm{l}}^{-1}$, ideal Faraday's laws of electrolysis predictThese are calculated predictions for complete conversion of the measured electric charge into retained copper, not experimental results. For a stable process, doubling the electric charge doubles the deposited mass; equal electric charge gives equal deposited mass even when the electric current and duration differ.

The balance reading is a test of the whole model. Competing reduction of water or other chemical species can divert electric current from copper deposition; transient electrode capacitance can also consume part of a short pulse without producing copper. A fragile deposit can detach even when its formation used the expected electric charge. Conversely, retained electrolyte or salts can increase an apparent mass gain. Comparing anode loss with cathode gain helps detect such problems but does not identify every cause. A slope below $M_{\mathrm{Cu}}/(2F)$ alone cannot distinguish competing chemical reactions from lost deposit. Current efficiency measures the fraction of transported electric charge assigned to a specified electrode reaction, rather than the fraction of electrical energy stored chemically.^[ref]

The beautiful connection is that an electrical measurement counts chemical events: integrating electric current and reading a balance provide two ways of following the same Electron stoichiometry. This makes electrolysis useful for controlling coating quantity and for testing a charge-to-amount of substance relation. It does not determine coating uniformity, adhesion or the required voltage, which depend on transport and electrode chemical kinetics as well.

An electrolyte is a conducting medium in which mobile ions carry electric current, according to IUPAC Gold Book: electrolyte. In introductory chemistry, a substance that yields ions when dissolved in water is also called an electrolyte. Both usages point to the same mechanism: an electric field gives mobile cations and anions directed drift velocities.

Mobility matters as much as the presence of electric charge. In a simple ideal model of solid sodium chloride, ions are confined to their sites and do not carry a sustained transport electric current. Molten sodium chloride has mobile ions; dissolved sodium chloride gives mobile ${\mathrm{Na}}^{+}$ and ${\mathrm{Cl}}^{-}$ ions in water. Real solids can have some ionic transport through imperfections; the immobile-solid picture is an introductory limit, rather than a claim that all solids are perfect insulators.

A strong electrolyte yields essentially all ions from the dissolved substance, whereas a weak electrolyte yields only a fraction under the specified conditions. Dissolved sodium chloride is a strong electrolyte. Sucrose is a nonelectrolyte: it dissolves as neutral molecules, so dissolving something does not automatically create mobile ions. Water's own small population of hydronium and hydroxide remains possible. See 11.2 Electrolytes (§11.2: strong, weak, and nonelectrolytes) and Flowers et al., Chemistry 2e, §11.4, Table 11.3: sucrose and sodium chloride.

Acetic acid is a weak electrolyte and a weak acid. In water, some neutral acetic acid molecules transfer a proton to water, producing hydronium and the negatively charged partner:Both sides have net electric charge zero. At chemical equilibrium, neutral acetic acid coexists with these ions; the fraction converted depends on the conditions. Electrolyte strength describes this extent of ion production, while concentration describes how much substance is present per specified quantity of chemical solution. A dilute strong electrolyte can contain fewer ions per volume than a concentrated weak electrolyte. Neither the words strong and weak nor a conductivity comparison alone specifies concentration.

Now specify an electrolytic cell with a positive anode on the left, a negative cathode on the right, and an approximately uniform electric field pointing right in the bulk electrolyte. With a steady external source and neglecting diffusion and convection, positive cations drift right toward the negative cathode; negative anions drift left toward the positive anode. Yet both populations contribute a rightward conventional current! For number densities $n_{+},n_{-}$ and drift velocities ${\mathbf{v}}_{+},{\mathbf{v}}_{-}$, the transport current density isThe product of electric charge and velocity determines conventional current: for the anion, both the charge and its rightward velocity component are negative, making its rightward contribution positive. This is the same sign rule used for Electron conventional current. It follows directly from the existing charge carrier formula.

For an independent numerical example, stipulate $n_{+}=n_{-}=10^{25}{\mathrm{m}}^{-3}$, $v_{+,x}=2\times 10^{-4}\mathrm{m}{\mathrm{s}}^{-1}$, and $v_{-,x}=-3\times 10^{-4}\mathrm{m}{\mathrm{s}}^{-1}$. With the exact elementary charge $e=1.602176634\times 10^{-19}\mathrm{C}$, the contributions areEqual number densities of singly charged cations and anions give zero bulk charge density, while their motion gives nonzero current density. This is why a neutral electrolyte can conduct. These numbers are chosen toy inputs, not measurements of sodium chloride; maintaining sustained cell electric current also requires suitable electrode reactions. Blocking electrodes can instead lead to charge accumulation and decay of the electric current.

An electrolyte connects the microscopic motion of ions to observable electrical conductivity. A counterion-only model keeps just the mobile counterions needed to oppose a fixed electric charge; Poisson-Boltzmann equations use ideal Boltzmann distributions to model their equilibrium distributions, rather than the drift example above.

An electrolytic cell uses an external source of electrical work to drive electrode chemical reactions. In the ordinary two-terminal driven mode, its positive anode supports oxidation and its negative cathode supports reduction. The source removes Electrons from the anode and supplies Electrons to the cathode; through the electrolyte, net conventional current goes from anode toward cathode. Terminal signs refer to the driven cell's terminals relative to each other. The source supplies electrical power to the cell. See 17.7 Electrolysis (§17.7: electrolysis and electroplating).

For example, transferring copper from a soluble copper anode onto a conducting object at the cathode has the ideal half-reactionsTheir sum transfers copper between surfaces. For identical bulk states, this transfer need not have a positive bulk Gibbs free energy change; finite electric current still needs applied drive to overcome losses. Thus "consumes electrical work" does not mean every electrolytic cell stores all that work as chemical Gibbs free energy. Electrolysis can instead redistribute material. The charge-to-amount relation remains $\xi =Q/(2F)$ when only these half-reactions carry the electric current; competing water reactions would change the deposited amount. The electroplating principle and charge accounting are described in 17.7 Electrolysis (§17.7: electroplating and quantitative aspects).

The University of Washington's teaching demonstration makes this material transfer visible with a copper electrode and a stainless-steel electrode in a glass cell containing $0.5\mathrm{mol}{\mathrm{L}}^{-1}$ $\mathrm{CuS}{\mathrm{O}}_4$. The external source connects its positive lead to copper and negative lead to steel; the reported observation is a copper coating on the steel. Reversing the source polarity removes the deposited copper again: the coated surface now supports oxidation and acts as the anode. This polarity reversal changes the drive, unlike swapping the measurement leads in the Daniell cell voltage and load experiment. Coating appearance alone does not measure charge efficiency or exclude competing chemical reactions. See University of Washington, Electroplating Copper on Stainless Steel: apparatus and reversible coating demonstration.

The copper cathode in this driven example is negative, while the copper cathode of a discharging Daniell cell is positive: both support exactly the same reduction half-reaction. Likewise, an anode need not lose material if its conducting surface is absent from its net half-reaction. Neither terminal sign nor a universal mass-change rule defines an anode or cathode.