A U-tube differential manometer contains a connected column of liquid with one gas connection above each liquid meniscus. Write for the left and right pressures, and for the meniscus heights on an upward vertical coordinate. Assume constant mass density and downward gravitational acceleration of magnitude ; neglect the gas column's mass density and differences in capillary pressure. The signed vertical length difference then gives
Larger left pressure means a lower left liquid meniscus: implies . Equal pressures give equal meniscus heights.
Figure 1. . Original schematic of two same-height pressure tappings connected to a resting water column. The constructed example uses and , so the vertical difference is . Dashed lines mark both meniscus heights and the equal-pressure datum; the dotted bottom line identifies two equal-height points within the connected liquid. The arrow in the pipe indicates fluid flow; the manometer liquid has no continuing flow at equilibrium. Details.
The balance follows directly from hydrostatic pressure. At a common height below both surfaces, the two points in the connected homogeneous liquid have equal pressure:
Subtracting cancels the common bottom depth and leaves . The same-height rule follows from hydrostatic equilibrium, : a horizontal displacement changes no pressure, and for constant the quantity is constant throughout the connected liquid. Equal height alone is insufficient for unrelated vessels or for fluid flow with significant acceleration.
For an original constructed example, choose water of stipulated mass density , gravitational acceleration , and vertical length difference . Then
The SI pressure unit is the pascal: the product has units . Swapping the two connections gives and reverses which liquid meniscus is lower. In equal-bore arms, volume conservation makes each surface move from its initial equal-height position; using only one surface's displacement would halve the inferred pressure. With unequal arm areas , a left fall and right rise instead obey , while the vertical length difference is still .
If the right port is open to the local atmosphere, is the left gauge pressure. Only with that reference and known atmospheric pressure can one obtain absolute pressure from
For an explicitly stipulated atmospheric pressure of , the example gives absolute pressure. If the right port is connected to another vessel or a pressure tapping, the same reading is a differential pressure and supplies no absolute pressure without knowing that reference.[ref]
Vacuum Created 2026-10-13 Updated 2026-11-05
A laboratory vacuum is a region with substantially reduced gas pressure, rather than an experimentally perfect absence of matter. Lowering the number density increases the mean free path, allowing a molecular beam to travel with fewer collisions. In molecular flow, the mean free path exceeds the apparatus dimensions, so wall encounters dominate.
A vacuum pump competes with leaks and outgassing. For an isothermal vessel of volume , constant gas load in pressure-volume per unit time, and effective pumping speed , gas balance gives
This ideal model predicts a pump-down time constant and a limiting pressure . A restricted connecting pipe reduces the effective pumping speed; a larger pump alone need not fix it. Measuring the pressure transient tests the model, while deviations can reveal changing outgassing or pumping speed.[ref]
Figure 1.
Ideal pump-down curves show an exponential transient and a floor set by the gas load
. Original calculations with stipulated constant volume, effective pumping speed and gas load. These illustrate the isothermal balance equation, not measured pump performance. Details.
Vacuum conductance 2026-11-05
Vacuum conductance relates gas throughput to a pressure difference across a connection: . For throughput in , conductance has units , the same units as pumping speed.
For a pump of speed connected through a line of conductance , a simple steady balance gives . Thus a pump behind a connection supplies only about at the chamber. Conductance depends on geometry, gas and flow regime; the pressure-independent molecular-flow value should not be used indiscriminately in viscous flow.[ref]
Vacuum distillation Created 2026-10-18 Updated 2026-11-05
A homogeneous canonical scalar field with positive scalar potential has energy density and pressure . When its potential energy dominates its kinetic energy, the equation-of-state parameter approaches . If other components and spatial curvature are negligible, the Friedmann acceleration equation gives accelerating expansion. Small initial kinetic energy is not enough to ensure long cosmic inflation; the field must also remain on a sufficiently flat part of the scalar potential, as measured by the potential slow-roll parameters.
Vacuum pump 2026-11-05
A vacuum pump lowers gas pressure by removing gas from a vessel or trapping it so that it no longer contributes to the free gas population. Mechanical displacement, momentum transfer and capture are distinct operating mechanisms.
Its relevant performance includes pumping speed, attainable pressure and gas dependence. The pressure achieved in an apparatus also depends on connecting vacuum conductance, leaks and outgassing; the pump's advertised limit is therefore not a complete system specification.[ref]
Vacuum technology 2026-11-05
Vacuum technology creates, measures and maintains gas pressures below the surroundings for experiments and manufacturing. Pumps remove gas while leaks, permeation and outgassing replenish it. Clean surfaces and appropriate materials can therefore matter as much as nominal pump capacity.
In a simple steady model, a gas throughput balanced by effective pumping speed gives . Connecting pipes reduce that speed through their vacuum conductance. The model assumes a specified gas, flow regime and suitable pressure-gauge interpretation; a pressure reading is not automatically a composition-independent measurement of every residual species.[ref]
Valve leaflet 2026-11-05
A valve leaflet is a mobile tissue flap forming part of a heart valve. Its movement and contact with neighboring leaflets help permit forward blood flow while limiting backward flow. The supporting cardiac valve annulus, the pressure difference and the leaflet's geometry all contribute to its behavior. The meeting of leaflet surfaces that closes a valve is called coaptation.[ref]
The mitral valve and tricuspid valve have leaflets supported by chordae tendineae and papillary muscles. The aortic valve and pulmonary valve instead have pocket-like cusps without that chordal apparatus. A leaflet is therefore a functional part of a particular valve structure, not an isolated rigid door.
An original force estimate illustrates the loading scale. A uniform pressure difference over an effective area gives a resultant . For stipulated kPa and cm, N. Doubling the area at the same pressure doubles this resultant, but it does not specify how the load is divided among attachments or distributed as tissue stress.
A primary left-heart simulator experiment measured chordae tendineae forces while moving papillary muscles and found responses that depended on the chordal type.[ref] This gives a concrete reason to examine leaflet geometry and supporting connections together. Complete coaptation is a contact-and-motion condition; an accurate measurement of one chordal force does not by itself show that the entire valve seals.
Van der Waals equation Created 2026-09-29 Updated 2026-10-14
The Van der Waals equation is a simple real gas equation of state that can also describe a liquid-gas critical point. With particle count fixed, write the volume per particle as :
or equivalently . Here is pressure, is absolute temperature, and is the Boltzmann constant. In SI, and have units per particle, has units , and has units ; the particle count is dimensionless. The pole at excludes smaller volume values from this model.
The correction represents excluded volume; the attraction term lowers pressure at fixed temperature and particle number density . This is a mean-field theory, replacing detailed intermolecular structure by two parameters. At with , it approaches the ideal gas law . It supplies a useful qualitative route from a dilute gas to phase coexistence, without a claim of quantitative accuracy for every fluid.[ref]
Do not mix this particle convention with the molar volume convention elsewhere in this article. With amount of substance , Avogadro constant , and molar gas constant , one has , , and , so . The molar parameters have units and , respectively.
Johannes Diderik van der Waals introduced this equation of state in 1873, connecting molecular attraction with departures from the dilute ideal gas law. Its historical significance is the unified treatment of gases and liquids, rather than a universally exact fit.[ref]
Van der Waals gas Created 2026-10-20 Updated 2026-11-05
A mean-field fluid model with excluded-volume and attractive-interaction parameters, described by the Van der Waals equation. Its pressure law alone does not fix every thermal property: the caloric closure of the van der Waals equation supplies the additional internal-energy assumption.
Van der Waals isotherm 2026-10-14
A Van der Waals isotherm is the pressure–particle volume curve at a fixed temperature. Put , , and , using the Van der Waals critical point values below. Then the existing Van der Waals law of corresponding states becomes
All curves in the figure are calculations in this reduced model.
Figure 1. . The dashed subcritical homogeneous continuation contains an unstable red segment. The green Maxwell construction plateau describes equilibrium phase coexistence; the two shaded areas are equal. Curves are model calculations, not carbon dioxide measurements. Details.
For a uniform thermodynamic phase, the isothermal compressibility is
Thus the upward-sloping portion of a subcritical Van der Waals isotherm has : compression would reduce pressure, allowing a density disturbance to grow. It is mechanically unstable. The spinodal points bound that portion; setting the derivative to zero gives their curve . Negative slope alone guarantees only local mechanical stability: portions between the spinodal and the phase coexistence endpoints have metastability. Equilibrium replaces the entire interval between those endpoints, including these metastable portions, by a Maxwell construction plateau.[ref]
Van der Waals law of corresponding states Created 2026-10-05 Updated 2026-11-05
The Van der Waals equation becomes independent of its material parameters when pressure, temperature and molecular volume are divided by their critical values: . This explains the common reduced isotherms within this model, without claiming exact agreement for all real fluids.
Van der Waals liquid-gas coexistence Created 2026-10-14 Updated 2026-10-18
Below , the equilibrium liquid and gas have the same temperature, pressure , and per-particle chemical potential. For macroscopic bulk thermodynamic phases, neglect interface contributions. The Maxwell equal-area construction determines and by
It expresses equality of chemical potentials, since at fixed temperature. Equivalently, the equilibrium Helmholtz free energy per particle follows a common tangent line between the two endpoint states, lying below the homogeneous continuation between them. The construction uses that mathematical continuation to compare endpoints; it is not a physical compression path through negative isothermal compressibility states.[ref]
Here is a reproducible calculated example at . With , the homogeneous intersections solve the cubic equation
The Maxwell construction gives
All three roots of a polynomial satisfy . Only the smallest and largest are the phase coexistence endpoints; the middle one has negative isothermal compressibility. Equal pressures at three admissible values of volume therefore do not imply three stable thermodynamic phases. An analytic area check is
At full numerical precision, the residual is below in reduced units; independent numerical integration gives the same cancellation. At , the spinodal points are instead and .
Figure 1. . The horizontal coordinate is reduced number density , not molar volume. The green region is equilibrium liquid–gas coexistence, bounded by the binodal. Hatching marks unstable homogeneous states, and the strips between solid and dashed boundaries mark homogeneous metastability. This is a model phase diagram, not measured data. Details.
The equilibrium plateau changes the phase fraction rather than the endpoint densities. For a gas particle fraction and mean particle volume , the lever rule reads
Thus at gives : this is a particle fraction, not the volume fraction occupied by gas. Differentiating equality of chemical potentials along this model's phase coexistence curve yields the same Clapeyron equation explained below, , with latent heat per particle. Both endpoint differences vanish as the Van der Waals critical point is approached; the equation's critical limit must be taken as a ratio.
The Maxwell construction presumes a pure bulk fluid at thermodynamic equilibrium. Its endpoint equality does not specify how rapidly a real compression reaches equilibrium. A homogeneous metastable sample can persist while nucleation is delayed; the spinodal marks loss of local mechanical stability in this mean-field theory, rather than the equilibrium onset of condensation. Surface tension, finite sample size and impurities can affect the observed transition. These qualifications matter when comparing a mathematical Van der Waals isotherm with a visible liquid meniscus.
The molar volume is the volume per amount of substance, not the total container volume or the volume per particle. In the molar convention of the Van der Waals equation, take constant positive parameters
Then
or, for any fixed amount of substance,
Both terms in the first equation are pressures. The total excluded volume is : using would subtract quantities with different units. Changing the sample size at fixed molar volume and temperature changes and proportionally, while leaving pressure unchanged. This is a useful unit and extensivity check before fitting a real gas.
For the molar Van der Waals critical point, differentiate with respect to molar volume at fixed temperature:
Setting both to zero gives and . Equating them and dividing by the nonzero factors yields , so
Here has units , has units , and has units . This is the molar version of the particle derivation below: , with the same physical and . If one writes , and without subscripts, then all of in those formulas must be molar quantities.
Now define the dimensionless reduced variables explicitly as , and . Substituting the three critical values cancels and gives
Because , these are exactly the reduced variables in the Van der Waals isotherm discussion. The Van der Waals law of corresponding states is therefore independent of whether one starts with particle or molar units. It predicts a critical ratio , providing a third check on any proposed parameter fit.
A hypothetical Van der Waals equation model illustrates positive and negative Joule-Thomson coefficient regions and a finite throttle that first warms, then cools. Use the molar convention already distinguished in Van der Waals equation:
Here is molar volume, the molar gas constant, internal energy per mole, and the stipulated constant molar heat capacity at fixed volume. The second equation is an additional caloric assumption: an equation of state alone does not specify the temperature dependence of internal energy. It satisfies the equilibrium identity . The arbitrary energy reference is set to zero.
Figure 1. . All curves are original model calculations, not nitrogen, carbon dioxide or other gas measurements. Colors label the response along constant molar enthalpy; arrows point toward lower pressure. The displayed states are above the model Van der Waals critical point temperature and have positive isothermal compressibility. The purple path crosses the zero-coefficient curve and has a temperature maximum. Details.
Define dimensionless variables , , and , where is molar enthalpy. These differ from the critical-value scaling in Van der Waals law of corresponding states. The throttle calculation reduces to
Thus a prescribed inlet fixes , and solving the first and last equations at the outlet pressure gives the final temperature. For an inlet and outlet , the model gives , a decrease of . The inlet instead gives , an increase of . The purple inlet initially warms but ends at for the same outlet pressure. These are reduced toy values, not kelvin readings or experimental evidence. No physical gas parameters were fitted.
For a short inversion derivation, implicit differentiation of the Van der Waals equation at fixed pressure gives
Insert this into and substitute back into the equation of state. The Joule-Thomson inversion curve is
Positive inversion pressure requires . Its maximum pressure is at , while the upper dilute limit is . Using Van der Waals critical point values, the latter is . The inversion locus depends on the equation of state; the chosen molar heat capacity additionally determines how much temperature changes along each finite throttle.[ref]
The displayed region has , above the model's critical temperature, and uses only , , and positive . Subcritical calculations require attention to phase coexistence, metastability and the Maxwell construction; an unstable homogeneous continuation is not an equilibrium throttle endpoint. Even on a stable branch, this mean-field theory with constant is a qualitative model, not an accurate inversion map for a particular real gas. Phase transitions, changing composition, appreciable heat leakage or bulk kinetic energy changes require a different property calculation or steady-flow energy balance. At phase coexistence, the smooth single-thermodynamic phase coefficient formula cannot replace a balance involving the phase fraction.
Vapor Created 2026-10-18 Updated 2026-11-05
A vapor is a substance in a gaseous state at a temperature where a condensed phase can also be reached under suitable pressure conditions. For a pure substance below its liquid-gas critical point, isothermal compression can reach phase coexistence and then convert some vapor to liquid. At coexistence the equilibrium vapor pressure depends on temperature.
A sealed cell containing both water and water vapor illustrates the distinction between amount and state: at fixed temperature, changing the liquid fraction can leave the equilibrium vapor pressure unchanged while both phases remain. A dilute vapor can still approximate an ideal gas, so vapor does not mean that ideal-gas calculations are automatically invalid. Conversely, the broad term gas does not imply ideal behavior. Specifying composition, temperature and pressure makes the usage physically meaningful.
Vapor-compression refrigeration Created 2026-10-14 Updated 2026-10-18
Vapor-compression refrigeration circulates a working fluid through cold and hot coils. In the cold coil, liquid becomes gas while absorbing heat from the refrigerated region. Compression supplies work and raises the pressure and temperature; the hot coil releases heat as the gas returns to liquid. A restriction reduces the pressure before the next cold-side passage. Changing the pressure changes the temperature of the phase transition, letting one circulating fluid receive and release heat at different temperatures. This physical implementation serves both refrigerators and heat pumps; its ordinary dissipative operation differs from the reversible Carnot cycle used to bound performance. [ref] [ref]
Vapor density 2026-10-31
The density of a vapor relative to a specified reference gas at the same temperature and pressure.
An ideal gas law measurement obtains amount of substance without knowing the chemical formula in advance:
Here is vapor pressure, is its occupied volume, is absolute temperature, is the molar gas constant, and is the mass of vapor occupying that volume at those conditions.
Santa Monica College's teaching experiment uses a Erlenmeyer flask with a pinhole foil cap, a water bath on a hot plate, a thermometer, and a barometer. Excess volatile liquid displaces air. A dissolved dye loses its colour and deposits when the liquid evaporates; three more minutes of heating follow. Cooling condenses retained vapor. Subtracting the dry assembly mass from the cooled assembly mass supplies . The flask volume comes from brim-full water mass and mass density at its measured temperature. Controls include a dry exterior, excluding bath water, and three trials.[ref]
The inference assumes vapor pressure equals atmospheric pressure, vapor and bath reach thermal equilibrium, the retained vapor mass is recovered on cooling, and the vapor obeys the ideal gas law. Residual air, thermal expansion of the flask, and vapor temperature below bath temperature are explicit error questions in the teaching experiment. Repeating trials assesses repeatability; it does not remove a shared bias.[ref]
Vapor-liquid equilibrium Created 2026-10-18 Updated 2026-11-05
Vapor-liquid equilibrium is coexistence of a liquid and its vapor with no net macroscopic transfer of matter between them. The two phases have equal temperature, equal pressure for a flat interface without external stress, and equal chemical potential for each exchanging species.
For a pure substance, fixing the temperature below its liquid-gas critical point selects the saturation vapor pressure. Molecules still cross the interface in both directions; equilibrium means equal average opposing rates, rather than halted molecular motion. In a mixture, the vapor and liquid generally have different compositions, while each component separately satisfies the chemical-potential equality. This distinction underlies separation by evaporation and condensation and explains why equal total pressure alone is insufficient to determine phase compositions.