An inductor stores magnetic energy and opposes changes of current through electromagnetic induction. For a fixed linear device, the flux linkage is , the self-induced electromotive force is , and the passive terminal voltage is . Hence
The voltage leads a sinusoidal current by a quarter cycle. A long solenoid has and ; its energy agrees with the volume integral of .
For two coupled coils, , , with signs set by coil orientations. Reciprocity gives the same mutual inductance in both equations. For the energy stored in a nonlinear inductor, replaces the simple quadratic formula, and hysteresis can dissipate energy. Real coils also have resistance, core loss and parasitic capacitance, so an ideal inductance model has a finite useful frequency range.[ref]
At an interface with unit normal pointing from medium 1 to medium 2, the magnetic boundary conditions are
The first follows from a pillbox applied to . The tangential magnetic field jump from a free surface current follows from a shrinking rectangular Ampère loop; is the free surface current. With no free sheet current, normal and tangential are continuous. In linear isotropic media , so neither all components of nor all components of generally remain continuous.
For magnetic field-line refraction at a permeability interface, with angles measured from the normal, these conditions give . They determine the bending of magnetic flux at a material interface. In a slender core electromagnet, flux continuity and Ampère's law lead to the magnetic-circuit estimate
An air gap can dominate the reluctance even when the iron core has high magnetic permeability. Boundary conditions also determine demagnetizing fields; fringing, saturation and hysteresis limit the simple linear circuit model. A high-magnetic permeability material redirects flux, whereas a perfect-conductor boundary is a different physical assumption.[ref]
Substitute the entropy differential into the given first law:
At fixed area, . Therefore
For reversible adiabatic stretching, and
The film cools, assuming positive heat capacity. Adiabaticity alone would not ensure constant entropy if the deformation were irreversible.
The reversible working substance changes entropy by on its hot isotherm and on its cold isotherm, with zero change on the two reversible adiabats. Closure requires . The substance has zero entropy change over a cycle, while the reservoirs have changes and . Thus for the complete Carnot cycle.
Suppose an engine were more efficient than a reversible Carnot engine between the same reservoirs. Couple it to a reversed Carnot engine, scaling the cycles to have equal work. With no net external work, their combined effect would be to transfer heat from the colder reservoir to the hotter one, contradicting the Second law of thermodynamics. No such engine can exceed . Equivalently, the cyclic entropy inequality gives , hence the same bound.
Dynamic viscosity measures resistance to a velocity gradient. In Newtonian simple shear, ; positive viscosity dissipates mechanical energy into heat. Kinematic viscosity is . For an incompressible fluid of constant viscosity,
Scaling velocity by and length by gives the Reynolds number , the ratio of inertial to viscous terms. At small Reynolds number, creeping-flow approximations neglect inertia; at large Reynolds number, inertia dominates much of the bulk but viscosity can remain crucial in boundary layers. A large Reynolds number permits instability and turbulence; it does not by itself specify a universal transition threshold. Geometry and disturbances also matter.
For two bodies interacting through , define
Their kinetic energy separates exactly:
Without external forces, the centre of mass moves uniformly while . The relative orbit is a one-body problem with reduced mass , not generally either individual mass. For , ; for equal masses , . If the interaction is central, relative angular momentum is conserved and the relative motion is planar.
For a rigid body about a chosen origin,
The inertia tensor is real and symmetric, so orthogonal principal axes diagonalize it. Angular momentum is parallel to angular velocity for rotation about a principal axis, but need not be parallel in a general direction. Its eigenvalues are the principal moments of inertia.
If the origin is translated from the centre of mass by , the parallel-axis theorem becomes . In body axes, Euler's equation is . Thus the full tensor is needed whenever the rotation is not confined to one fixed principal axis.
An isotropic linear elastic solid has two independent elastic constants. For infinitesimal strain,
The shear modulus governs shape change and the bulk modulus governs volume change. Young's modulus and Poisson's ratio are equivalent parameters:
Positive strain energy requires , hence ; is the incompressible limit. Small-amplitude bulk waves have speeds and . Isotropy removes directional dependence, not the distinction between compression and shear. These laws apply within the elastic small-strain regime, not after yielding or fracture.
Guided electromagnetic waves propagate along a structure whose boundaries select transverse field patterns. At a perfect conductor the tangential electric field vanishes. In a hollow rectangular guide, TE modes have and TM modes have . Their longitudinal wavenumber obeys
Below the waveguide cutoff frequency , that mode is evanescent rather than freely propagating. TM modes require both indices positive; TE modes may have one zero but not both. For , the lowest cutoff is the TE mode, with . A hollow single-conductor guide has no TEM mode, whereas a two-conductor transmission line can support one without this geometrical cutoff.[ref]
For a propagating TE or TM mode, and . The phase velocity can exceed without superluminal information transfer. Frequency-dependent group delay can broaden pulses; excitation of several modes adds intermodal dispersion.
Because , a magnetic vector potential can be introduced with . It is not unique: gives the same field. In magnetostatics, the Coulomb gauge gives in vacuum. For localized electric currents,
A magnetic scalar potential is more restricted. In a simply connected current-free region of constant permeability, write ; then . Alternatively define the scalar potential for , differing by a constant permeability factor. A single-valued scalar potential generally cannot cover a domain encircling a net electric current, even where the local curl vanishes. The vector potential does not require the field itself to be curl-free.
In magnetostatics, Ampère's circuital law in vacuum is
It is especially useful when symmetry makes the tangential field constant on an Amperian loop. It gives for an infinite straight wire, inside a long solenoid, and in an ideal toroid. The long-solenoid and toroidal expressions neglect fringing.
For time-dependent fields, displacement current is essential:
In matter, the corresponding macroscopic form is . The enclosed electric current alone is sufficient only in the magnetostatic limit.
The Biot-Savart law gives the magnetic field of a steady thin-wire electric current in vacuum:
The cross product fixes the circulation direction by the right-hand rule; fields from different electric current elements superpose. Integration gives outside a straight infinite wire and at the centre of a circular loop of radius . A distributed electric current replaces by . This is a magnetostatic law: arbitrary time-dependent electric currents require retarded electromagnetic fields, not instantaneous substitution.
At a perfect conductor, the reflected electric field cancels the incident tangential field, while their magnetic fields add. Thus and has peak amplitude . Taking the zero-penetration limit, including its surface force, gives
Reversal of the normal momentum doubles the pressure compared with absorption at the same incident Poynting flux.
With no reflected field, and at the entrance. Thus
Complete absorption transfers the incident normal momentum flux to the body.
A source much deeper than the annual penetration depth has K. Therefore
The ideal coldest-day electrical-input ratios are direct : air-source : deep-ground = 1 : 0.0853 : 0.0171. The deep source needs one fifth of the ideal air-source work. These ratios compare equal useful heating, and do not include excavation, circulation losses or an assumed real compressor efficiency.
For the ideal reversible comparison, K and the coldest air source is K. Thus
A real air-source pump uses more work than this reversible lower bound, and its low-temperature performance is not specified.
The coldest day has outside temperature , so the indoor–outdoor temperature difference is 25 K. If is the building's heat-loss coefficient, the required heating rate is . For direct electrical heating,
This sets the reference electrical cost for the same delivered heat and tariff.

Pinned article: Introduction to the OurBigBook Project

Welcome to the OurBigBook Project! Our goal is to create the perfect publishing platform for STEM subjects, and get university-level students to write the best free STEM tutorials ever.
Everyone is welcome to create an account and play with the site: ourbigbook.com/go/register. We belive that students themselves can write amazing tutorials, but teachers are welcome too. You can write about anything you want, it doesn't have to be STEM or even educational. Silly test content is very welcome and you won't be penalized in any way. Just keep it legal!
We have two killer features:
  1. topics: topics group articles by different users with the same title, e.g. here is the topic for the "Fundamental Theorem of Calculus" ourbigbook.com/go/topic/fundamental-theorem-of-calculus
    Articles of different users are sorted by upvote within each article page. This feature is a bit like:
    • a Wikipedia where each user can have their own version of each article
    • a Q&A website like Stack Overflow, where multiple people can give their views on a given topic, and the best ones are sorted by upvote. Except you don't need to wait for someone to ask first, and any topic goes, no matter how narrow or broad
    This feature makes it possible for readers to find better explanations of any topic created by other writers. And it allows writers to create an explanation in a place that readers might actually find it.
    Figure 1.
    Screenshot of the "Derivative" topic page
    . View it live at: ourbigbook.com/go/topic/derivative
  2. local editing: you can store all your personal knowledge base content locally in a plaintext markup format that can be edited locally and published either:
    This way you can be sure that even if OurBigBook.com were to go down one day (which we have no plans to do as it is quite cheap to host!), your content will still be perfectly readable as a static site.
    Figure 5. . You can also edit articles on the Web editor without installing anything locally.
    Video 3.
    Edit locally and publish demo
    . Source. This shows editing OurBigBook Markup and publishing it using the Visual Studio Code extension.
  3. https://raw.githubusercontent.com/ourbigbook/ourbigbook-media/master/feature/x/hilbert-space-arrow.png
  4. Infinitely deep tables of contents:
    Figure 6.
    Dynamic article tree with infinitely deep table of contents
    .
    Descendant pages can also show up as toplevel e.g.: ourbigbook.com/cirosantilli/chordate-subclade
All our software is open source and hosted at: github.com/ourbigbook/ourbigbook
Further documentation can be found at: docs.ourbigbook.com
Feel free to reach our to us for any help or suggestions: docs.ourbigbook.com/#contact