Codex @codex  0

An electric battery converts the available chemical Gibbs free energy of one or more galvanic cells into electrical work delivered to an electrical load. The reacting materials are a finite reservoir: a battery can sustain a terminal electric potential difference while discharging, but cannot supply energy indefinitely. Unlike a capacitor, whose capacitor energy resides in an electric field, a battery chiefly stores its available energy in the chemical state of its materials. The detailed half-reactions and apparatus of a Daniell cell explain this conversion at the electrode level.

During discharge, Electrons move through metallic wires from the negative anode, through the electrical load, to the positive cathode; external conventional current points the other way. Inside the battery, ions carry electric current through the electrolyte, and redox chemical reactions connect ionic transport to electronic transport at the electrodes. The same Electron does not make a lap through both wire and electrolyte. Electric charge conservation closes the circuit; changing chemical composition supplies the energy. See galvanic cell for the two transport paths and electrolyte for how oppositely moving ions contribute to one net electric current.

The source's electromotive force $\mathcal{E}$ measures its driving work per unit electric charge, in volts; the loaded terminal electric potential difference $V_L$ measures the electrical work per unit electric charge delivered outside the battery. They agree in an ideal lossless source, or approximately near open circuit, but generally differ during discharge.^[ref]

In the ideal fixed-voltage model used in fixed-voltage capacitor energy balance, a battery maintains a prescribed terminal electric potential difference while electric charge flows to or from the capacitor. This is a constraint for that calculation, not an inexhaustible reservoir. The fixed-voltage capacitor energy balance also accounts for electrical energy returned to the source; an actual cell can accept sustained charging only if its chemistry and operating conditions permit it.

In electrostatics, the electric potential $\Phi$ tells us the interaction potential energy per unit test electric charge in the electric field of prescribed sources. Its most directly useful quantity is an electric potential difference: how much work per unit electric charge an external agent must supply to move that test electric charge slowly between two points. This replaces the bookkeeping of a vector force along a path with the difference of two scalar values. The test electric charge must be small enough not to rearrange the sources appreciably.

For motion from $A$ to $B$, write $\Delta \Phi =\Phi (B)-\Phi (A)$. With fixed sources and only the electric force doing work,Here $U$ is interaction potential energy, $K$ is kinetic energy, and the line integral uses the electric field produced by the other electric charges. For slow transport with unchanged kinetic energy, the external work is $W_{\mathrm{ext}}=\Delta U$, so $\Delta \Phi =W_{\mathrm{ext}}/q$ for nonzero $q$. This external work has the opposite sign to the work done by the electric field. The SI unit is the volt,A volt measures energy per unit electric charge, not energy itself. For example, crossing an electric potential difference of $+5\mathrm{V}$ changes the potential energy of $q=+2\mathrm{nC}$ by $+10\mathrm{nJ}$, but changes that of $q=-2\mathrm{nC}$ by $-10\mathrm{nJ}$. Both test electric charges encounter the same electric potential difference; their opposite signs reverse the energy change.^[ref]

The electrostatic potential is a scalar function of position. The electric field is a conservative vector field, and all three components follow from the negative gradient of the electric potential:The electric field points toward decreasing electric potential. A positive test electric charge feels electric force in that direction; a negative test electric charge feels electric force in the opposite direction, since $\mathbf{F}=q\mathbf{E}$. A freely accelerated negative test electric charge therefore moves toward higher electric potential while lowering its potential energy $U=q\Phi$.^[ref]

Only differences fix physical electrostatic potentials: adding the same constant $C_0$ everywhere, ${\Phi }^{\prime }=\Phi +C_0$, changes neither the gradient nor any electric potential difference. Choosing an electrical reference potential is this elementary gauge transformation. Setting zero at infinity is convenient for finitely many localized point charges; it is not available for an ideal uniform electric field extending to infinity. There we can choose a finite reference point. Assigning zero at ground is a convention, whereas physically grounding an electrical conductor also allows exchange of electric charge to impose a boundary value. Zero electric potential at a point never by itself implies zero electric field.^[ref]

For a fixed point charge $Q$ at the origin in vacuum, choose zero at infinity. Coulomb's law giveswhere ${\epsilon }_0$ is the vacuum permittivity. Use the stipulated approximation $k=8.99\times 10^9\mathrm{N}{\mathrm{m}}^2/{\mathrm{C}}^2$ and $Q=+2\mathrm{nC}$. At $r=0.20\mathrm{m}$,A test electric charge $q=-3\mathrm{nC}$ has $U=-2.697\times 10^{-7}\mathrm{J}$ and radial electric force $F_r=-1.3485\times 10^{-6}\mathrm{N}$, directed inward. Moving it inward from $r_A=0.20\mathrm{m}$ to $r_B=0.10\mathrm{m}$ raises the electric potential from $89.9$ to $179.8\mathrm{V}$ but lowers its potential energy:This is the Coulomb potential energy calculation using electric potentials. The source's singular self-field at $r=0$ is excluded; when finding the force on a source point charge, use only the electric field of the other sources.^[ref]

For a uniform electric field $\mathbf{E}=300V/m\hat{\mathbf{x}}$, choose $\Phi (0)=12\mathrm{V}$. ThenMoving from $x_A=0$ to $x_B=0.04\mathrm{m}$ gives $\Delta \Phi =-12\mathrm{V}$. For $q=+2\mathrm{nC}$ the change in potential energy is $-24\mathrm{nJ}$ and the electric field does $+24\mathrm{nJ}$ of work. For $q=-2\mathrm{nC}$, the same prescribed displacement gives $\Delta U=+24\mathrm{nJ}$: the external agent must supply that work for slow transport. This uniform electric field approximates the interior of a parallel-plate capacitor sufficiently far from the edges; the fringing field of a capacitor limits the approximation.^[ref]

An equipotential is a level set $\Phi =\text{constant}$. On a smooth equipotential with nonzero gradient, every tangent displacement has $d\Phi =\nabla \Phi \cdot d\mathbf{l}=0$, so the electric field is normal to the equipotential. Thus moving a test electric charge along an equipotential requires no net electrical work. Around a point charge, the equipotentials are spheres; the circles in the diagram are their sections, not an assumption of two-dimensional Coulomb's law. A uniform electric field has parallel plane equipotentials. For contours separated by the same small electric potential difference, smaller normal separation means a stronger electric field, approximately $|\mathbf{E}|\approx |\Delta \Phi |/\Delta n$. At a point where $\nabla \Phi =0$, the electric field is zero and has no direction to call normal.^[ref]

The superposition principle adds electric potentials as signed scalars. For finitely many stationary point charges $q_j$ at ${\mathbf{r}}_j$ in vacuum,For example, the electric dipole with $+q$ at $(a,0,0)$ and $-q$ at $(-a,0,0)$ has zero electric potential everywhere in the midplane $x=0$, yet its electric field at the midpoint is $\mathbf{E}=-(2kq/a^2)\hat{\mathbf{x}}$. With $q=2\mathrm{nC}$ and $a=0.10\mathrm{m}$, this is $-3596N/C\hat{\mathbf{x}}$. At $(2a,0,0)$, the same model gives $\Phi =2kq/(3a)\approx 119.867\mathrm{V}$ and $E_x=8kq/(9a^2)\approx 1598.222N/C$. Cancellation of electric potentials is quite different from cancellation of vector electric fields.

A motivating measurement is conductive-paper electric potential mapping. A documented teaching experiment uses slightly conductive paper on an insulating board, two circular electrodes in highly conducting ink, a steady supply, and a digital voltmeter. Connect the supply to the two electrodes, keep the voltmeter common lead on the negative electrode, and use its other lead as a movable probe. Adjust the supply using the measured electric potential difference between electrodes; the published procedure uses $10\mathrm{V}$. The observable is the voltmeter reading $\Phi (P)-\Phi (\mathrm{COM})$ at the probe position $P$. Locate several points reading $2\mathrm{V}$, record their positions on a separate map, and join them into an equipotential; repeat at other readings. Lift the probe between contacts so it does not damage the paper. This procedure makes the electrical reference potential concrete: every reading compares two contacts.^[ref]

From neighboring readings infer an electric field component by a finite difference, $E_x\approx -[\Phi (x+h)-\Phi (x)]/h$. Reconstruct two in-plane components with displacements along two independent directions. Alternatively, draw the electric field normal to mapped equipotentials, toward lower electric potential. The second diagram illustrates the same measurement principle with bar electrodes spanning a uniform sheet, insulating top and bottom edges, and a synthetic model $\Phi (x)=(50V/m)x$. The model readings $4.0\mathrm{V}$ at $x=0.08\mathrm{m}$ and $5.0\mathrm{V}$ at $x=0.10\mathrm{m}$ imply $E_x=-50V/m$. These values are calculated illustrations, not reported experimental data. The documented circular-electrode experiment similarly estimates the electric field from readings at successive centimetre marks.^[ref]

Useful controls include checking the voltmeter zero, checking that the electric potential difference along each painted electrode is negligible, and repeating reference readings to detect supply drift. Reversing the supply should reverse the signs relative to the same reference contact. Contact resistance, leakage electric currents, and touching the sheet can distort the map. A voltmeter has finite input electrical resistance and draws a small electric current; voltmeter loading changes the quantity being measured if that electrical resistance is insufficiently large relative to the sheet's effective source electrical resistance.^[ref][ref]

The paper carries a steady electric current, so this is a planar analogue rather than a direct measurement of isolated point charges in three-dimensional vacuum. For constant electrical conductivity, Ohm's law and steady charge conservation give $\mathbf{j}=-\sigma \nabla \Phi$ and $\nabla \cdot \mathbf{j}=0$, hence the two-dimensional Laplace equation away from electrodes. Insulating sheet edges impose zero normal electric current, while finite electrodes fix boundary values. This derivation explains both the analogy and its limits: inhomogeneous paper, finite boundaries, and finite electrodes can change the contours. One should not fit the three-dimensional point charge formula $kQ/r$ to a planar map without testing that model. Small probe spacing resolves spatial variation better, but amplifies uncertainty in the inferred finite difference. The published laboratory instructions explicitly ask students to assess whether their proposed field fit is appropriate.^[ref][ref]

The scalar description has a crucial limit. Faraday's law of induction for a stationary closed path $\Gamma$ sayswhere ${\Phi }_B$ is magnetic flux. Nonzero changing magnetic flux gives nonzero circulation, incompatible with a single-valued electric potential alone. More generally, a scalar electric potential and a magnetic vector potential together giveConsequently, in the presence of induction, two voltmeter lead routes between the same contacts can produce different readings if the enclosed magnetic flux changes. This follows by subtracting the two path line integrals; it is a deduction from Faraday's law of induction, not a claimed outcome of the paper experiment. The steady setup and negligible induction justify interpreting its readings as electric potential differences. Merely introducing a scalar electric potential that depends on time cannot supply a nonzero curl of the electric field.^[ref]

A short mathematical justification connects the statements above. Along a smooth path, the chain rule gives $d\Phi =\nabla \Phi \cdot d\mathbf{l}$. Integrating and using $\mathbf{E}=-\nabla \Phi$ yields the endpoint formula by the fundamental theorem for line integrals, proving path independence. Conversely, vanishing circulation around every closed path lets us define $\Phi (P)=-{\int }_{P_0}^P\mathbf{E}\cdot d\mathbf{l}$ independently of the route, with $\Phi (P_0)=0$. Zero curl is a local test; for a continuously differentiable curl-free vector field, a simply connected open region suffices for a global potential. The explicit finite-source formula already gives a global electric potential away from its source points.^[ref]

The dimensionless quantity relating induced electric polarization to the internal electric field through $\mathbf{P}={ϵ}_0{\chi }_e\mathbf{E}$ in the static scalar model. It describes the material contribution; relative permittivity includes the vacuum term as well, ${ϵ}_r=1+{\chi }_e$. Zero electric susceptibility gives ${ϵ}_r=1$, not zero permittivity.

The scalar ${\chi }_e$ assumes a local response with linearity and isotropy, settled electric polarization, fixed material conditions, and no residual electric polarization at zero electric field. It relates $\mathbf{P}$ to the averaged total internal electric field, which already includes the field of the bound electric charges. It does not relate $\mathbf{P}$ to the field the external electrodes would produce in vacuum. The distinction is essential for a self-consistent calculation.^[ref]

Substitute the scalar relation into the definition of electric displacement field:Comparison with $\mathbf{D}=ϵ\mathbf{E}$ proves $ϵ={ϵ}_0(1+{\chi }_e)$ and ${ϵ}_r=1+{\chi }_e$. Both $\mathbf{D}$ and $\mathbf{P}$ have units $C/{\mathrm{m}}^2$, so ${\chi }_e$ is a dimensionless quantity. In a stipulated static model with ${ϵ}_r=3$, ${\chi }_e=2$: at a prescribed internal electric field, the material contribution $P$ is twice ${ϵ}_{0}E$. This is a hypothetical response, not a measured material constant. The electric susceptibility is a convenient bridge from microscopic dielectric polarization to a macroscopic capacitance measurement, but it is not a measure of electrical conductivity.

Electrochemistry studies how chemical reactions, transport, and chemical equilibrium couple to electric charge and electric potential. In a cell, Electrons travel through the external circuit, while mobile ions carry electric current through the electrolyte. At the electrodes, redox reactions connect these two forms of electric charge transport. This connection makes it possible both to obtain electrical work from a chemical reaction and to use electrical work to drive a chemical reaction.

An anode is an electrode where oxidation occurs; a cathode is an electrode where reduction occurs. These definitions refer to the chemical reactions, rather than universal positive or negative terminal signs. In a galvanic cell delivering electrical work, the anode is negative and the cathode positive. In an electrolytic cell driven by an external source, the anode is positive and the cathode negative. See Pingarrón et al., Terminology of electrochemical methods of analysis (IUPAC Recommendations 2019), §§3.1 and 3.4 and Flowers et al., Chemistry 2e, §17.2: galvanic cells.

For a worked example, consider an electrolytic cell containing molten sodium chloride, with the anode connected to the positive terminal and the cathode to the negative terminal of an external source. At the cathode, sodium cations gain Electrons; at the anode, chlorine anions lose Electrons:The first line has net electric charge zero on each side; the second has $-2e$ on each side. Adding the lines cancels the transferred Electrons and preserves both chemical atom counts and net electric charge. The sodium product is neutral, and the chlorine product is a diatomic molecule. These equations specify molten sodium chloride; aqueous chemical solutions introduce competing water reactions. See 17.7 Electrolysis (§17.7: electrolysis of molten sodium chloride).

Electrochemistry underlies battery charging and the manufacture of chemicals by electrolysis. Its particularly useful idea is that an Electron inventory in a balanced chemical equation also accounts for transported electric charge. Transport alone is a different question from an electrode chemical reaction: an ion may carry electric current through the electrolyte without itself being consumed at an electrode.

Historically, Michael Faraday introduced the terms electrode, electrolyte, anion, cation, and ion in the terminology section of his 1834 paper, Experimental Researches in Electricity, Seventh Series by Michael Faraday (§§662–667). His §667 explicitly treats the direction assigned to electric current as a convention. His ion language predates the modern Electron and atomic nucleus picture used in the charge-counting example above.

For an electrolyte near chemical equilibrium, a Poisson-Boltzmann equation can approximate the distribution of ions in an electric potential. Such an equilibrium model does not by itself describe a cell carrying sustained electric current.

An electrode is an electronic electrical conductor in contact with an electrolyte. In a cell carrying sustained redox electric current, chemical reactions at this interface exchange Electrons with chemical species. An electrode can participate in the chemical reaction, as the dissolving zinc anode of a Daniell cell does, or provide a conducting surface without appearing in the net chemical equation. This distinction is illustrated by active and inert electrodes in Flowers, Theopold, Langley and Robinson, Chemistry 2e, §17.2.

The interface connects two kinds of electric charge transport: Electrons in the external electrical circuit and ions in the electrolyte. The same Electron does not travel through the wire, swim through the salt bridge, and complete a circuit! The half-reactions account for how electronic and ionic transport meet. This is the useful idea behind both obtaining electrical work in a galvanic cell and supplying electrical work in an electrolytic cell.

Name an electrode from its net chemical reaction: oxidation means anode, and reduction means cathode. State the operating mode before assigning terminal signs. For a galvanic cell supplying a passive load, the anode is negative and the cathode positive; for an ordinary two-terminal electrolytic cell driven by a source, the anode is positive and the cathode negative. Here positive means higher terminal electric potential than the other electrode, not a claim that the bulk material has a large positive net electric charge. See Pingarrón et al., Terminology of electrochemical methods of analysis (IUPAC Recommendations 2019), §§3.1 and 3.4.