Spark-excited damped oscillation 2026-10-18
A spark gap can rapidly discharge a charged capacitor through an inductor. After excitation, the stored energy runs down through Joule heating, radiation and other losses. A key held down can permit repeated discharges: each discharge starts a damped train of rapid oscillations. The spark repetition frequency, the electrical oscillation frequency within each train, and the rate of keyed symbols are different quantities. Repetition does not make each train a maintained sinusoid.
An original lumped model replaces the conducting spark gap and other losses by a constant total electrical resistance in an isolated series RLC circuit. For electric charge on the capacitor, the Kirchhoff cycle law givesFor , its characteristic roots are , with , proving the stated damped form. The electric current has the same exponential decay scale. Its wave envelope falls by per cycle; the energy envelope falls twice as fast in the exponent. A maintained sinusoid instead requires continuing input power balancing losses.
With , and , the model gives , Q factor , amplitude time constant , and damped frequency . These are chosen component values. A real spark gap switches nonlinearly, an antenna radiates, and coupling exchanges energy between circuits; one constant- free decay does not model the complete transmitter. Rapid damping also broadens the frequency spectrum, which helps explain why short trains make sharp receiver selection difficult.
For an equal-duty square wave alternating between with period , the steady periodic capacitor voltage has extrema . A positive half-period maps to , proving the title formula. The negative half-period is its sign-reversed copy. Short periods give a small nearly triangular output; long periods give input-like plateaux with exponential transitions.
Summing amplifier 2026-10-25
An inverting operational amplifier can combine currents from several input resistors at one virtual ground. Kirchhoff's current law and negligible amplifier input current give the displayed weighted sum. Replacing the feedback resistance by a capacitor gives a weighted op amp integrator. The formulas assume stable negative feedback and operation within the amplifier's linear output range.
Supply rate 2026-11-05
A supply rate specifies the instantaneous quantity whose time integral is compared with a change of storage function in dissipativity. With control input , plant output and state , a chosen function enters the balanceThe supply rate can be negative: it then represents net withdrawal in the chosen accounting. Its physical interpretation depends on the variables and sign convention, rather than on the word supply alone.[ref]
Dissipative Dynamical Systems, Part I: General Theory by Jan C. Willems. General Theory, definition of supply and storage inequality
For a mechanical terminal with applied force and inward-convention velocity , choose , the entering power. For an electrical terminal with electric current entering its positive-potential terminal, the corresponding choice is , with an electric potential difference. Both have units of watts when is energy. Reversing one terminal sign without changing the other reverses the apparent power flow.
An original capacitor example illustrates the sign. Let , terminal electric potential difference , and charging electric current . Its stored electrostatic energy is , and at that instant . With the same potential and , the supply rate is and storage decreases. This is consistent with nonnegative stored energy; negative supply does not mean negative storage.
A different supply rate can express a signal-performance requirement:Nonnegative final storage and zero initial storage then bound accumulated output-square by times accumulated input-square. These squares need not be physical power. Scaling or changing the units of the signals requires corresponding changes in the coefficients. A general real quadratic choice can be written as , with symmetric ; the selected quadratic form states which input–output relation is being tested.
Telegrapher's equations 2026-10-18
A distributed transmission line with per-unit-length series resistance , series inductance , shunt conductance and shunt capacitance obeys the displayed coupled first-order equations by applying Kirchhoff's voltage law and Kirchhoff's current law to a short element. With , both voltage and current satisfy a wave equation with speed and characteristic impedance . The quantities are distributed parameters, not a single lumped resistor or capacitor.
Thomas M. Blooming 2026-11-05
Thomas M. Blooming is an electrical engineer whose coauthored Capacitor Application Issues by Thomas M. Blooming and Daniel J. Carnovale addresses practical use of capacitor banks in electric power systems. Its author biography describes work on power factor correction, harmonic filtering and related application measurements.[ref]
Capacitor Application Issues by Thomas M. Blooming and Daniel J. Carnovale. Printed p.1, byline; p.14, Authors' Biographies, Thomas M. Blooming
A useful technical question is why improving fundamental displacement power factor can alter the response to other harmonic components. In an original lossless parallel LC circuit, the admittance isIts reactive terms cancel at the resonant frequencyFor stipulated and , . Doubling moves it to about . A correction component chosen for one operating frequency has therefore changed the network at other frequencies as well.
In this ideal parallel model the impedance diverges at resonance; a finite imposed harmonic electric current would demand an unbounded electric potential difference, signaling the ideal model's limit. Real losses and other network elements bound and shift the response. A proposed bench test uses a small known drive and sweeps frequency with and without the extra capacitor, recording both current and potential difference. It tests the frequency-dependent circuit rather than inferring behavior from the fundamental cosine alone.
The calculation is an original illustration of the network question, not an experimental result attributed to Blooming. His joint paper with Daniel J. Carnovale supplies the application context: component choice and operating conditions must be considered together. A correction that looks favorable in a single-frequency power factor calculation is not, by that fact alone, characterized across the full waveform.
An electronic comparator registers a pulse only if its input reaches the chosen threshold. For an initially uncharged capacitor driven through an electrical resistance , a short rectangular pulse may end before that happens. The resulting threshold-crossing time of a finite rectangular pulse through an RC load depends on threshold and pulse duration, as well as the time constant ; it is not determined by group delay alone.
Take a positive input electric potential difference for , zero input outside that interval, and output across a capacitance . Include the source's effective series electrical resistance in . The initial condition is . Kirchhoff's voltage law and the capacitor current relation give the first-order linear differential equationThe output is a continuous function and reaches its maximum at the pulse's falling edge:The input jumps there, but an ideal capacitor's stored electric charge cannot change discontinuously under the finite currents of this model.
Choose a fixed threshold with . Solving the rising exponential function using a natural logarithm givesIf , the output never reaches the threshold. At , it touches the threshold only at its peak; the ideal time spent strictly above threshold is zero. A nonzero high interval in an ideal non-inverting electronic comparator requires . This is RC pulse-width discrimination: different input durations can give a missing pulse or a finite output pulse even when their input heights are equal.
For , solving the falling exponential decay givesHere is the time above threshold for an RC-filtered rectangular pulse, before any electronic comparator switching dynamics. It is not generally the input duration . Just above , differentiation gives and hence to first order; a half-height threshold gives slope two at the detection boundary.
For an original numerical example, take , , , and , so . A input peaks at only and is rejected. A input peaks at and givesThese are model calculations, not recorded instrument traces.
A threshold near the asymptotic input height is also especially sensitive to noise and threshold measurement uncertainty. Holding the absolute input height and fixed, the threshold timing sensitivity of an RC step response isFor the same , model, a effective threshold perturbation gives approximately of timing change at , but at , by first-order uncertainty propagation. The rectangular pulse must still last long enough to reach the selected threshold; changing together with is a different sensitivity calculation.
A bench test uses a pulse generator and an oscilloscope to record both the applied electric potential difference and the capacitor output. Sweep while keeping and the actual threshold fixed, and allow enough time between pulses for the measured initial output to be negligible at the desired precision. Include probe and comparator-input capacitance in . MIT's laboratory measures RC decay with a capacitor, a resistor and square-wave excitation; that gives a directly measurable component-value time constant.[ref]
Laboratory 11: Sinusoidal Steady State Response of RC and RL Circuits by MIT OpenCourseWare. Printed pp. 1–2, component values and decay/phase measurements
The pulse-duration sweep proposed here extends that decay measurement to a threshold observation. A real electronic comparator's input offset voltage, hysteresis and finite switching time must be separated from the ideal RC crossing times; a Schmitt trigger uses different rising and falling thresholds.The threshold-reset margin for a periodic RC pulse train is the separation between the reset threshold of an electronic comparator and the largest baseline that the periodic RC low-pass filter may leave between pulses. A positive margin excludes missing comparator reset in an RC pulse train in the ideal threshold model; its size measures tolerance to additional electric potential difference errors.
Let be the input high level, the high duration, the quiet duration and the time constant. From the periodic solution in missing comparator reset in an RC pulse train, writeThis defines a margin in volts, rather than in units of standard deviation. If a nominal baseline has a known absolute error bound and the reset threshold has bound , a sufficient worst-case condition isThese are simultaneous bounds on the actual baseline and threshold. Adding their standard uncertainties would not by itself provide a deterministic guarantee; a probabilistic statement requires a specified joint probability distribution.[ref]
Guidelines for Evaluating and Expressing the Uncertainty of NIST Measurement Results by Barry N. Taylor and Chris E. Kuyatt. §§6.2–6.3, distributional conditions for interpreting uncertainty intervals
For an original example, let , and . Then , and the peak is . A threshold of gives . Bounds and leave . Raising the baseline bound to would remove this guarantee even though the nominal waveform still crosses the threshold.
A positive minimum separation does not specify the reset dwell time below threshold in an RC pulse train. A real electronic comparator needs enough time to switch, and the peak must separately exceed the acceptance threshold. For a Schmitt trigger, use the lower switching threshold in , while checking the upper one against the peak.
A focused bench test records the pulse generator output, capacitor output and electronic comparator output on an oscilloscope, then varies near the predicted boundary. Compare the measured minimum with the reset threshold and record the low interval as well as the minimum. The underlying exponential decay can be checked by the natural-response experiment in the MIT laboratory; the margin calculation above is an original application of that model.[ref]
Laboratory 11: Sinusoidal Steady State Response of RC and RL Circuits by MIT OpenCourseWare. Printed p. 1, capacitor response after switching and time-constant measurement
Transistor small-signal amplifier 2026-10-18
An original teaching model exposes the roles of input loading, output loading and the supply. Choose a small-signal model with positive input electrical resistance , transconductance , and output electrical resistance . Its controlled output current source draws from the output node toward the reference node. This chosen sign gives an inverting voltage gain; it is not the historical contact circuit's sign convention.
Assume a fixed operating point, negligible reverse coupling, a frequency range where coupling capacitors pass the signal, and negligible other capacitances and transit delays. A collector resistor connects the output to a steady ideal supply ; an external electrical load is coupled through a capacitor, so it draws no direct current. The input source has series electrical resistance . All voltages below are small departures from the operating point. An ideal fixed supply has zero incremental voltage and therefore becomes the reference node in the small-signal model.
Define and , where . Input voltage division and output Kirchhoff's current law giveConsequently the port voltage gain, overall source-to-output voltage gain, and load current gain magnitudes areThis current gain uses load electric current, not all the controlled-source electric current. It is also a different port definition from the historical emitter-to-collector current gain. Larger attenuates the input; smaller attenuates the output.
For a sinusoid input signal, use root mean square voltages. The power gain from accepted input signal power to useful load power isUnlike , this tends to zero as either or . Differentiation givesThus matching the output electrical load maximizes delivered power in this unilateral resistive model. For fixed source voltage, input loading multiplies by ; the accepted-input power gain above excludes the loss in .
Choose , , , and . Then . With and root mean square, the input is and the inverted output has magnitude root mean square. Hence and : . These are calculated values of the chosen model, not historical measurements.
With the same parameters but , while . At , while . Neither current gain nor voltage gain alone establishes power gain.
For the direct current load line in the figure, choose , and , consistent with . Locally extend the model as . With the external electrical load isolated at direct current, its intersection with is . Keeping small compared with the available voltage headroom is essential; extrapolation to arbitrarily large signals would be unphysical.
At the chosen operating point the collector supply delivers : is dissipated in and in the output device. Under a small signal, that energy flow is redistributed to provide load power. The incremental controlled current source hides the supply's steady energy flow; it does not create energy. A real complete amplifier also needs its input biasing network and has further losses. This calculation establishes neither its total efficiency nor a universal law for point-contact transistors.
Tuned spark wireless apparatus 2026-10-18
Guglielmo Marconi's 1909 lecture describes antennas with earth connections and separate coupled receiving circuits. His 1900 system coupled a closed capacitor–inductor–spark gap loop to a transmitting antenna. Coil spacing adjusted coupling; inductance and capacitance adjusted tuning. All four circuits were tuned together. By 1909 his company's stations mainly used magnetic receivers, rather than coherers.[ref]
Wireless Telegraphic Communication by Guglielmo Marconi. 1909 lecture, Figs. 2–3, 6 and 8 and associated paragraphs; receiver paragraph at Fig. 25
Those are a participant's retrospective descriptions, not a complete account of priority. An earth connection is part of this antenna arrangement; it is not a universal requirement for radio communication. Nor does tuning an isolated LC circuit ensure that its frequency remains unchanged when strongly coupled to another circuit. The coupled resonant circuit model quantifies that distinction.
Voltage multiplier 2026-10-18
An electrical circuit that uses diodes and capacitors to produce an output electric potential difference larger in magnitude than the input peak. The attainable output depends on the circuit arrangement, electric current drawn by the load, capacitance and input frequency; an ideal unloaded result does not specify the output under load.
Wien bridge 2026-10-18
An alternating-current electrical circuit comparing a parallel resistor-capacitor arm with a series resistor-capacitor arm. Let the upper-left arm have electrical impedance , the lower-left arm , and the upper-right and lower-right arms have electrical resistances . For input between the upper and lower nodes and an unloaded difference measurement between the arm junctions, voltage divider balance requires . Separating real and imaginary parts givesThe balance angular frequency is positive for positive components. Equal and require and . Reversing which reactive arm is upper changes the divider ratios, so the connections must always be specified.
Zero-input response 2026-11-05
The zero-input response is the output due to a system's initial internal state when its externally applied input is set to zero. It describes memory left by earlier excitation. For a linear time-invariant system, linearity separates this from the zero-state response due to the subsequent input.
For constant matrices in , , setting and givesThe matrix exponential solves the homogeneous state equation. With an arbitrary input, the complete solution adds the zero-state response:A zero initial output alone does not establish that the whole state is zero.
For an RC circuit with capacitor difference and no applied source, , so . The capacitor energy falls as ; the resistor receives the dissipated energy. The primary MIT lecture explicitly distinguishes the capacitor's initial state, zero external input and zero initial state.[ref]
State and Memory by Anant Agarwal and Jeffrey Lang. PDF pages 2–6, RC memory and zero-input/zero-state decomposition
At a time constant and , the modeled difference after two seconds is . Zero input has not meant zero output or zero stored energy. A direct experiment charges the same capacitor to different known initial differences, removes the charging source and records the decay across a fixed resistor. The amplitudes should scale with while the normalized decay remains the same in the linear model.
A zero-input response need not decay in every system: an ideal undamped oscillator retains its initial motion, and an unstable homogeneous system can amplify a nonzero initial state. The transfer function describes the zero-state input-output map, so its product with a zero input cannot represent a separate nonzero initial-state contribution.
Zero-state response 2026-11-05
The zero-state response is the output produced by an applied input when the system starts with zero internal state. For a linear time-invariant system it separates the effect of the input from the zero-input response caused by an initially stored state. A zero initial output alone need not mean zero internal state.
For a causal linear time-invariant system with impulse response , the zero-state response is the convolutionAn instantaneous feedthrough term, if present, is represented by a Dirac delta term in . Equivalently, for constant matrices in , with ,For nonzero , linearity adds the zero-input response . Here the matrix exponential propagates the state left by the earlier input.
For example, with , and a constant input for has the step response . At one time constant it has reached about of its final value. If the initial value instead equals , the total output is . A charged capacitor in an RC circuit provides a direct physical example: discharge it before repeating the same input step to isolate the zero-state response, and compare with a run from a known initial electric potential difference.[ref]
State and Memory by Anant Agarwal and Jeffrey Lang. PDF pages 2–6, capacitor memory and separate zero-state/zero-input responses
With compatible transforms, the zero-state input-output relation is , where is the transfer function. For a nonzero initial state, a unilateral Laplace transform includes additional initial-condition terms. Those terms cannot be absorbed into an input-independent transfer function multiplying .

