From the illuminated side downward, the p-type gallium arsenide cap provides a low-resistance route to the front metal contact. It should remain beneath the contact grid but be removed from the optical aperture to reduce parasitic absorption. The wider-band gap p-type aluminium gallium arsenide window transmits much of the useful light and reduces front-surface recombination of carriers in the adjacent absorber. The optical-window and reduced-recombination rationale has a primary experimental basis in early heteroface devices.[ref]
High-efficiency Ga1-xAlxAs-GaAs solar cells by Jerry M. Woodall and H. J. Hovel. Applied Physics Letters 21 (1972), p. 379, transparency and surface-recombination rationale; p. 380, contacts and antireflection coating
The p-type gallium arsenide emitter and n-type gallium arsenide base form the p-n junction. Absorbed photons generate electrons and electron holes; diffusion and the junction's electric field direct them toward the appropriate contacts. The n-type aluminium gallium arsenide back-surface-field layer provides a barrier to minority holes moving toward the substrate and reduces rear recombination. The n-type gallium arsenide substrate supports the epitaxial layers and conducts majority carriers to the rear contact.
The front metal must collect current with limited shading and the back metal provides the return contact. Interpreting the patterned hatched region as the optical antireflection coating, it reduces reflected light over the exposed window. Carrier selectivity, low recombination, low series resistance and low shading must work together; the equilibrium junction field alone is not a source of electrical energy.
Past exam of the physics A course of the University of Cambridge 2015 Paper 2 Section D D12 Solution 2026-10-20
A completely filled valence band carries no net current: its occupied crystal-momentum states have velocities that cancel. Near a valence-band maximum, an almost full band is conveniently described by the few missing electrons, or electron holes. Removing an electron of charge , with , changes the charge relative to the filled band by . This is a quasiparticle description of electronic motion, not a mobile positive ion or a Positron.
For an isotropic parabolic maximum, . Assign the missing-electron state momentum and hole energyIt has positive effective mass . Its velocity equals the velocity of the missing electron state, and its positive-charge current replaces the negative of that state's electronic current. Semiclassical motion is thus . With momentum relaxation time , the low-field mobility is andIf electrons also contribute, : the two species' longitudinal conductivities add.
A Hall bar separates carrier concentration from mobility. Apply current density , magnetic field , and measure transverse electric field . For one isotropic hole population, transverse force balance gives , soFor thickness , the Hall-voltage magnitude is . A longitudinal four-terminal resistance measurement supplies independently. Use ohmic contacts, known conducting thickness, controlled temperature and low enough current to avoid self-heating. Reversing magnetic field removes even-in-field longitudinal offsets from contact misalignment; reversing current also helps reject thermoelectric offsets. These are central controls, rather than merely taking one transverse voltage reading.[ref]
Resistivity and Hall Measurements by National Institute of Standards and Technology. Sample Geometry; Resistivity Measurements; Definitions for Hall Measurements; Hall Measurements and Hall Calculations
The simple inference assumes one carrier type and a known Hall scattering factor. More generally , so measures Hall mobility rather than automatically the drift mobility. With two carrier populations at weak field,Its sign alone need not identify the more numerous carrier. A Hall experiment also cannot determine and separately: their ratio sets mobility. cyclotron resonance supplies an independent mass measurement by sweeping frequency or magnetic field through and detecting resonant absorption. The measured cyclotron effective mass can depend on band anisotropy and need not equal every curvature mass; the isotropic parabolic model identifies them. Its linewidth provides a scattering-time estimate only with a specified damping model.
semiconductor doping generates holes by adding acceptor impurities. In silicon, a substitutional group-III atom such as boron provides one fewer valence electron than silicon. A shallow acceptor level lies slightly above the valence-band edge: accepting a valence electron makes the dopant negatively ionized and leaves a mobile hole in the valence band. The impurity stays fixed in the lattice. charge neutrality and the nondegenerate equilibrium mass-action law giveFor fully ionized, uncompensated acceptors in the extrinsic regime, and ; with fully ionized donor compensation, while holes remain dominant. The Fermi level moves towards the valence band. At low temperature, semiconductor carrier freeze-out suppresses mobile electron holes; at high temperature intrinsic electron-hole generation can dominate. Increasing dopant density also changes scattering, so a conductivity increase alone cannot distinguish increased carrier density from changed mobility. Temperature-dependent Hall and conductivity measurements separate these effects, subject to the carrier and scattering qualifications above.
Past exam of the physics A course of the University of Cambridge 2016 Paper 2 Section A 5 Solution 2026-10-20
The effective mass follows from the curvature of the electronic band structure. Differentiating twice givesAt either first Brillouin zone boundary ,The boundary is a band maximum, with negative curvature and zero group velocity. In the semiclassical single-band description, an applied force changes ; the resulting acceleration is opposite the force near that maximum. This is a band-response coefficient, not a negative microscopic electron rest mass. A nearly filled band is often described more conveniently through positively charged electron holes near its maximum.
The free electron model replaces the detailed periodic potential by a constant background, treating conduction electrons as mobile particles with approximately parabolic dispersion . It is useful to distinguish the classical Drude model from the quantum free electron gas. They share a simple transport picture, but differ fundamentally in occupation statistics.
With a momentum-relaxation time , both lead in a simple isotropic one-band approximation toThis explains approximately Ohmic longitudinal conduction and a carrier-density scale from the Hall effect. The relaxation time is phenomenological: introducing it does not itself predict scattering from defects or phonons. A four-probe resistance measurement separates the sample's longitudinal response from current-contact voltage drops; field and current reversals isolate the transverse signal.
The classical model incorrectly assigns roughly of electronic heat capacity, far too large in a degenerate metal. Fermi-Dirac statistics fixes this: most occupied states cannot change occupation after a small thermal perturbation because nearby low-energy states are already filled. Only a fraction of order near the Fermi energy participates. For ,The quantum model also gives a finite Fermi velocity even at zero temperature and Pauli paramagnetism. Under predominantly elastic scattering, its electronic heat and charge conductivities obey the Wiedemann-Franz law,This is a quantum success; classical equipartition does not give the correct small heat capacity and Lorenz number together.
Its limitations are equally instructive. Without the periodic potential it has no band gaps, so it cannot distinguish a filled-band insulator from a metal or explain semiconductor doping. The simplest single-electron Hall formula cannot explain positive Hall coefficients; band curvature and electron holes, or a multiband transport treatment, are needed. It neglects much Fermi-surface anisotropy and detailed optical interband absorption. Noninteracting electrons alone do not explain ferromagnetism or superconductivity, and lattice thermal behavior needs phonons. The nearly-free electron model, which allows reciprocal-lattice Fourier components of the potential to mix plane waves, provides a controlled first correction near Bragg planes.
Its main success is a simple quantitative baseline for degenerate conduction electrons; its main failure is treating the crystal and interactions as too featureless. A fit of conductivity alone is not a test of the whole model: compare heat capacity, Hall sign, optical response and temperature dependence using independently constrained parameters.
Past exam of the physics A course of the University of Cambridge 2017 Paper 2 Section C C11 Semiconductor bands and efficient light emission Created 2026-10-18 Updated 2026-10-20
A semiconductor has a filled valence band and an empty conduction band at zero temperature in the intrinsic idealisation, separated by a modest band gap. Thermal excitation or deliberately introduced impurities can create mobile electrons and electron holes. Its conductivity is consequently very sensitive to temperature and doping. A metal has available electronic states at the occupied energy boundary, through a partly filled band or overlapping bands, and need not thermally excite carriers across a gap.
For a direct band gap, the conduction-band minimum and valence-band maximum occur at the same crystal momentum. An electron can recombine with a hole near these extrema and emit a photon while conserving crystal momentum, since optical photon momentum is small on the lattice scale. For an indirect band gap, the extrema lie at different crystal momenta. A band-edge radiative transition then ordinarily needs a phonon as well, making it less probable and allowing nonradiative processes to compete more effectively.
gallium arsenide has a direct fundamental gap, while silicon has an indirect one. This makes efficient band-edge emission and hence a light-emitting diode easier to obtain from gallium arsenide. It does not mean silicon has no optical transitions or that every direct-gap sample emits efficiently: defects, surfaces and carrier confinement also matter.
Past exam of the physics A course of the University of Cambridge 2017 Paper 2 Section D D13 b Solution Created 2026-10-18 Updated 2026-10-20
A band effective mass describes the acceleration of an electronic wavepacket in a periodic lattice through the local band curvature. It incorporates the periodic lattice potential into a useful transport parameter without changing the bare electron mass. For a Bloch state in an isolated band,Differentiation givesIn one dimension this becomes . A locally parabolic isotropic band minimum has with positive . A flatter band has a larger effective mass. At a band maximum the electron curvature is negative, so the electron accelerates oppositely to the applied force. Describing the missing electron as a positive-charge electron hole with positive mass is often simpler.
In the scalar relaxation-time approximation, a conduction electron in an electric field reaches . ThusFor a crystal with different directional curvatures, conductivity is a tensor and involves the occupied states and their scattering. Contributions from electrons and holes add: in an isotropic two-carrier description. A filled band contributes no ordinary longitudinal current because opposite group velocities cancel; a partially filled band or holes permit a current response.
Effective mass therefore connects measured electrical transport to electronic band structure, but carrier density and momentum relaxation time matter as much as curvature. Ionised impurities and phonons alter . A smaller mass does not guarantee a higher conductivity if carrier population or scattering changes. Nor are all reported masses identical: density-of-states, cyclotron and conductivity masses weight anisotropic bands differently. The simple semiclassical formula assumes an isolated band, slowly varying weak fields and negligible interband transitions; near degeneracies or strong fields a single constant scalar mass is inadequate.
Past exam of the physics A course of the University of Cambridge 2018 Paper 2 Section C C11 a Solution Created 2026-10-18 Updated 2026-10-20
A Bloch state in a crystal experiences a periodic lattice potential. Its band dispersion relation encodes the lattice response, so an effective mass allows a wavepacket's acceleration under a weak applied force to be described without explicitly following the microscopic periodic forces.
In one dimension the wavepacket group velocity and semiclassical equation for crystal momentum areDifferentiating the first equation with respect to time givesDefining yieldsThis band effective mass is controlled by band curvature, not the slope. A band minimum has positive ; a band maximum has negative electron and is often more conveniently described with positive-mass electron holes. In three dimensions the inverse effective mass is generally a tensor, . The scalar formula assumes motion along a specified direction in an isolated band, weak fields and negligible interband transitions; the bare electron mass has not physically changed.
Past exam of the physics A course of the University of Cambridge 2018 Paper 2 Section D D12 Solution Created 2026-10-18 Updated 2026-10-20
Doping changes the mobile carrier population by introducing controlled impurity levels. In an intrinsic semiconductor, the filled valence band is separated from the nearly empty conduction band by a band gap . Thermal excitation produces an electron-hole pair, so the electron and hole number densities obey . A electron hole represents a missing valence-band electron and behaves as a mobile positive charge carrier. For nondegenerate bands in thermal equilibrium,Here are the effective density of states, the band edges, and denotes the chemical potential, conventionally called the Fermi level. The semiconductor mass-action law holds in this nondegenerate equilibrium regime.
In a tetrahedrally bonded elemental semiconductor such as silicon, a substitutional group-V atom has an extra outer electron relative to the host. It is a donor impurity: a shallow level just below can ionise, releasing an electron to the conduction band and leaving a fixed positively charged donor. The resulting n-type semiconductor has electrons as majority carriers and holes as minority carriers. Conversely a group-III substitution supplies one fewer bonding electron. An acceptor impurity can take an electron from the valence band, leaving a mobile electron hole and a fixed negative acceptor; the resulting p-type semiconductor has holes as majority carriers.
The impurity state is shallow because the electron or hole responds to a screened Coulomb potential and an effective mass, rather than the bare atomic potential. A simple hydrogenic donor estimate iswhere is the relative permittivity. This is a useful scaling model, with real band anisotropy and central-cell effects omitted. Dopants are fixed in the lattice; their ionisation changes mobile carrier numbers without making a uniformly doped bulk sample carry a large net electric charge.
The charge neutrality condition isWhen shallow dopants are almost fully ionised and , an n-type region has and . A p-type region similarly has and . Thus compensation by the opposite impurity type reduces the majority-carrier density; the total dopant concentration is not generally the mobile carrier density. At sufficiently high impurity density the degenerate semiconductor regime requires the full Fermi-Dirac distribution and these exponential approximations fail.
There are three useful temperature regimes. At low temperature, dopant freeze-out leaves many shallow levels un-ionised. In the extrinsic regime, the dopants are largely ionised and set the majority-carrier density. At high enough temperature, intrinsic pair creation dominates and approach . The Fermi level moves towards the conduction band with donor doping and towards the valence band with acceptor doping. The electrical conductivity isDoping therefore controls conductivity and its carrier type, but ionised impurities also scatter carriers and can reduce charge carrier mobility. Carrier density and mobility must both be considered.
A p-n junction forms when p-type and n-type regions are joined within a semiconductor. Initially the concentration gradients drive diffusion current: electrons diffuse from the n region to the p region and holes in the opposite direction. Recombination removes mobile majority carriers near the join, exposing fixed positive donors on the n side and fixed negative acceptors on the p side. This forms a depletion region and an electric field directed from n to p. Its drift current opposes diffusion. At equilibrium the net current vanishes and the Fermi level is uniform, although the band edges vary spatially through band bending.
For an abrupt nondegenerate junction with fully ionised dopants, its built-in potential isUnder the depletion approximation, the space-charge densities are on a p-side width and on an n-side width . Integrating Poisson equation and imposing zero field outside gives andMost of the depletion width therefore extends into the more lightly doped side. The schematic shows the impurity levels before contact and the resulting space charge and potential after contact; there is no externally extractable equilibrium battery voltage from the built-in field alone.
Shallow donor and acceptor levels, and charge, field and potential in an equilibrium abrupt p-n junction
. Details. A forward bias, with p positive relative to n, reduces the barrier from towards and injects minority carriers across the junction. In the ideal low-injection, diffusion-controlled regime this produces the Shockley diode equation, . Reverse bias increases the barrier and the depletion region; only a small thermally generated minority-carrier current flows before breakdown. Reverse-biased depletion regions also give a voltage-dependent junction capacitance. Real devices have recombination, leakage, series resistance and breakdown mechanisms beyond the ideal law. Controlled doping creates majority and minority carriers, and their junction produces a depletion barrier that makes rectification possible.
Past exam of the physics A course of the University of Cambridge 2019 Paper 2 Section A 4 Solution Created 2026-10-18 Updated 2026-10-20
Take an abrupt equilibrium p-n junction with the p side at and the n side at . In the quasi-neutral bulk, electron holes are the majority carriers on the p side and electrons are the majority carriers on the n side. With ionized dopant densities and nondegenerate statistics,where is the intrinsic carrier concentration. The semiconductor mass-action law applies at equilibrium. Both mobile populations are small in the depletion region compared with the dopant densities.
The charge and carrier density of an abrupt p-n junction must distinguish mobile populations from net charge. Diffusion leaves negatively charged ionized acceptor impurities on the p side and positively charged ionized donor impurities on the n side. Under the depletion approximation,The neutral bulks have large carrier densities but nearly zero net charge density. The electric field points from the positive donor region toward the negative acceptor region, balancing diffusion at equilibrium.
Illustrative equilibrium carrier densities and depletion-approximation net charge for a symmetric abrupt p-n junction
. Details. The figure uses equal dopant densities only to show a simple symmetric sketch. Generally the more lightly doped side has the wider depleted interval. The carrier profiles are smooth, whereas the step-shaped net charge density is the ideal depletion approximation.
Past exam of the physics A course of the University of Cambridge 2019 Paper 2 Section D D13 b Solution Created 2026-10-18 Updated 2026-10-20
Semiconductor doping introduces controlled impurities to alter equilibrium carrier populations and electrical conductivity. In an intrinsic semiconductor, thermally excited electrons in the conduction band and electron holes in the valence band have equal densities . A shallow donor impurity, such as phosphorus in silicon, supplies an electron from an impurity level just below the conduction-band edge. Once ionized it is positively charged, and the material is n type. An acceptor impurity, such as boron in silicon, accepts a valence electron into a level just above the valence-band edge, leaving a mobile hole and a negatively charged ionized impurity; the material is p type.
With dopant densities , charge neutrality requiresFor fully ionized, nondegenerate dopants at equilibrium, the semiconductor mass-action law gives . In a substantially n-type sample, , soThe corresponding p-type result is and . The majority population grows while the minority population decreases; adding donors does not simply add equal numbers of free electrons and holes.
The Fermi energy shifts toward the conduction band for n-type material and toward the valence band for p-type material. In the nondegenerate approximation,where are effective band-edge state densities. At very low temperature, dopants may not be ionized and carrier freeze-out occurs. At intermediate temperatures, ionized dopants dominate the carrier density; at sufficiently high temperature, intrinsic excitation can dominate. Heavy doping can produce degenerate carrier statistics, invalidating these Boltzmann expressions.
The electrical conductivity is . Doping usually raises the majority carrier density, but ionized impurity scattering can lower mobility, so conductivity need not scale indefinitely with dopant concentration. Joining p-type and n-type regions creates a p-n junction, with a depletion region and built-in electric field established by carrier diffusion and compensating drift. The fixed ionized dopants, not an absence of all charge, account for the depleted region's net charge density.
Past exam of the physics A course of the University of Cambridge 2021 Paper 2 Section C C8 d Solution Created 2026-10-18 Updated 2026-10-20
Twice the quadratic coefficient from the previous part is the band curvature . Thus the band effective masses areHere and . In the weak-potential regime ,Both have units of mass; their magnitudes are much smaller than in this asymptotic regime. The upper energy band has a local minimum and positive effective mass, while the lower energy band has a local maximum and negative effective mass. The exact lower-branch sign changes at in the two-wave formula; the intended weak-coupling limit lies below that threshold.
The physical meaning follows from the semiclassical equations for an electron wave packet in one energy band:An upper-band electron near its minimum accelerates in the direction of the applied force, whereas a lower-band electron near its maximum accelerates opposite to it. At the extremum itself the group velocity is zero. A nearly filled lower energy band is conveniently described by electron holes with positive electric charge and positive effective mass . Negative curvature is a response of a crystal energy eigenstate, not a negative bare electron mass. These statements assume slow forcing that does not induce transitions across the band gap.
Past exam of the physics A course of the University of Cambridge 2022 Paper 2 Section A 4 Solution Created 2026-10-18 Updated 2026-10-20
Take a p-n junction made from one semiconductor, with the p-type semiconductor on the left and the n-type semiconductor on the right. At thermal equilibrium the chemical potential is horizontal throughout. Before contact the chemical potential lies nearer the valence band on the p side and nearer the conduction band on the n side; after contact the band edges bend to permit one common value.
Original equilibrium p-n junction energy band diagram, impurity levels, common chemical potential and depletion region
. Details. In this orientation both the conduction band edge and the valence band edge decrease from p to n by . For a homojunction their separation is constant. The acceptor impurity level lies just above where acceptors are present, and the donor impurity level lies just below where donors are present. These impurity levels follow the local band bending; they do not form one additional horizontal band across the device.
The shaded depletion region has few mobile electrons or electron holes and contains fixed negative ionized acceptor impurities on the p side and positive ionized donor impurities on the n side. Thus its electric field points from n to p. Its neutral outer regions have negligible electric field, so the band edges become flat there. In the depletion approximation, charge neutrality requires ; the symmetric drawing illustrates rather than assuming that equality is universal. Diffusion and field-driven drift current cancel at equilibrium: no applied voltage does not mean zero internal electric field or zero built-in electric potential difference.
Past exam of the quantum condensed matter course of the University of Cambridge 2004 Section A 3 Solution Created 2026-10-18 Updated 2026-10-20
In a p-n junction, diffusion and electron-hole recombination near the contact leave a depletion region of ionized dopants. Its built-in electric field opposes further majority-carrier diffusion. At thermodynamic equilibrium drift and diffusion currents cancel. Forward bias lowers the electrostatic barrier and injects electrons and electron holes across the junction; reverse bias raises the barrier and suppresses that majority-carrier injection. For an ideal diode below breakdown,Thus a modest forward voltage gives a rapidly increasing current, whereas reverse current remains approximately . This asymmetric current-voltage relation makes the junction a rectifier. Real leakage, electron-hole recombination and breakdown limit the ideal expression.
Past exam of the quantum condensed matter course of the University of Cambridge 2004 Section B B9 a Solution Created 2026-10-18 Updated 2026-10-20
Charge carrier mobility measures weak-field drift speed per electric field. For electrons and electron holes,Both mobilities are positive, with SI units ; the opposite drift signs reflect the opposite carrier charges. In a simple isotropic relaxation-time model, electron mobility is and hole mobility is . These are momentum relaxation times, not the minority carrier lifetime for electron-hole recombination.
Scattering by phonons, ionized impurities and defects limits mobility. Increasing phonon populations commonly lowers mobility at high temperature; ionized-impurity scattering can dominate at low temperature and high semiconductor doping. Approximate addition of independent inverse relaxation times is the Matthiessen's rule. At sufficiently strong field, velocity saturation invalidates the constant-mobility drift law.
The Hall effect provides a measurement: a current-carrying bar in a perpendicular magnetic field develops a transverse voltage. In a one-carrier model and , combining the transverse voltage with longitudinal electrical conductivity. Multiple carrier types and scattering-dependent Hall factors require a more detailed interpretation.
Past exam of the quantum condensed matter course of the University of Cambridge 2004 Section B B9 c Solution Created 2026-10-18 Updated 2026-10-20
An n-channel MOSFET has two heavily n-doped source and drain regions in a p-type body, with an insulated gate above the intervening surface. A positive gate voltage first depletes surface electron holes and then induces an electron semiconductor inversion layer. Above threshold this layer connects source to drain. Gate voltage controls the channel charge through the oxide capacitance, while the insulating gate permits a very small steady gate current.
For the long-channel MOSFET current law, let be oxide capacitance per area, channel width and length, and use constant mobility . In the gradual-channel approximation,At larger drain voltage the ideal channel pinches off near the drain and the current saturates atCarriers still flow through the pinch-off region; pinch-off does not mean zero drain current. These formulas neglect channel-length modulation, short-channel effects and velocity saturation. A p-channel device reverses the carrier type and operating polarities. Gate control makes MOSFETs useful as electronic switches and amplifiers.
Past exam of the quantum condensed matter course of the University of Cambridge 2012 1 a Solution Created 2026-10-18 Updated 2026-10-20
A positive electric potential difference between gate and substrate attracts electrons towards the insulating interface and repels the mobile electron holes of the p-type semiconductor substrate. The exposed, negatively charged acceptor impurities form a depletion region; the thin mobile electron layer at its surface is the semiconductor inversion layer. The conduction band and valence band bend downwards towards the positively biased gate, because the electron potential energy is .
Band bending and charge separation at the conventional MOS inversion threshold
. Details. To specify the conventional MOS inversion threshold, let be the ionized acceptor density, the intrinsic carrier concentration, andIn the neutral bulk the intrinsic level lies above the semiconductor chemical potential. A positive surface potential lowers both band edges by , giving, in the nondegenerate approximation,At , the surface is intrinsic: . The usual onset of strong inversion instead meansThus the surface electron density has grown to the bulk majority-carrier density. The chemical potential need not actually enter the conduction band. The phrase “just forms” can also refer to the earlier weak-inversion crossover; the diagram uses the conventional strong-inversion threshold and labels it explicitly.
Within the depletion approximation the negative space charge is approximately over a widthwhere is the absolute semiconductor permittivity. Its outer edge is where the bands become flat and mobile electron holes recover their bulk density. The electrical insulator blocks steady carrier transport while sustaining an electric field; the metal gate supplies positive surface charge balancing depletion and inversion charge. Under gate bias, the gate and substrate electrochemical potentials are different, so a single equilibrium Fermi level should not be drawn through the whole biased stack.
Past exam of the quantum condensed matter course of the University of Cambridge 2012 2 a Solution Created 2026-10-18 Updated 2026-10-20
A solar cell uses the photovoltaic effect to turn photon energy into electrical work. In a semiconductor, above-gap photon absorption generates an electron in the conduction band and an electron hole in the valence band. A p-n junction, together with selective electrical contacts, collects the two carrier species at opposite terminals. Carrier diffusion and the built-in electric field help separate them before electron-hole recombination. Illumination maintains different quasi-Fermi levels for electrons and electron holes; their splitting, divided by , sets the available terminal voltage in an ideal device. The equilibrium built-in potential alone cannot continuously deliver work.
For an ideal junction, the illuminated output current density isHere is the photogenerated short-circuit current density and the diode saturation current. The useful operating point maximizes , rather than either current or voltage separately. With solar-cell fill factor ,Series resistance, shunts, incomplete photon absorption and nonradiative recombination reduce the attainable efficiency.
The Shockley-Queisser limit removes these avoidable losses but retains the following physical constraints. There is one semiconductor junction with one band gap; each absorbed above-gap photon yields at most one collected electron-hole pair; carriers thermalize to the cell temperature; and the inverse optical process produces unavoidable radiative recombination. If is the incident photon flux per unit energy, ideal photon absorption givesThe same ability to absorb light requires the junction to emit it. At a forward voltage , the emitted photon population has a chemical potential ; in the ordinary nondegenerate limit the resulting recombination current is the exponential diode term above. Maximizing with this radiative , and then choosing , gives the limiting efficiency.
A small band gap collects many photons but gives a low voltage and large thermalization losses. A large band gap permits a larger voltage but transmits too much of the incident spectrum. Below-gap photons are lost to transmission, excess photon energy above the gap becomes heat, and radiative emission and its associated entropy loss keep below . The optimum single-junction conversion is roughly thirty percent under ordinary unconcentrated sunlight; the precise ceiling depends on spectrum, cell temperature and optical geometry. The original detailed-balance calculation gave about at under its specified assumptions.[ref]
https://doi.org/10.1063/1.1736034. Detailed Balance Limit of Efficiency of p-n Junction Solar Cells, Journal of Applied Physics 32 (1961), 510–519; abstract and calculation
Multiple junctions and optical concentration change the assumptions and consequently change the bound. Past exam of the quantum condensed matter course of the University of Cambridge 2013 3 Solution Created 2026-10-18 Updated 2026-10-20
Dopant atoms and carrier type. Substitutional semiconductor doping places a small fraction of foreign atoms on host lattice sites. In a tetrahedrally bonded group-IV semiconductor, a group-V substitution such as phosphorus in silicon has an extra valence electron. A shallow donor level just below the conduction edge can release that electron, leaving a positively charged donor. In an n-type semiconductor, mobile electrons are the majority carriers and the chemical potential shifts toward the conduction band.
A group-III substitution such as boron in silicon has one fewer valence electron. An acceptor level just above the valence edge captures an electron from the valence states, leaving a mobile electron hole and a negatively charged acceptor. In a p-type semiconductor, electron holes are the majority carriers and the chemical potential shifts toward the valence band. The material can remain electrically neutral in both cases: mobile carrier electric charge is compensated by fixed ionized impurity electric charge. Dopant freeze-out, compensation and degeneracy qualify the simplest one-carrier-per-dopant picture.
Making the junction. Choose p material at and n material at . Electrons initially diffuse from n to p, and electron holes from p to n, recombining near the interface. Negative ionized acceptors are exposed on the p side and positive ionized donors on the n side. They produce an electric field directed from n to p. The field opposes further majority-carrier diffusion until drift and diffusion balance and the equilibrium electrochemical potential is uniform.
The depletion regions are depleted of mobile majority carriers, not of the fixed dopant charges that create the space charge. At equilibrium the conduction and valence edges bend together, while the chemical potential is flat. The specified is a electric potential difference: the corresponding initial chemical-potential energy separation is . This convention is required by the quoted units and width formulas. Write for the absolute permittivity; the paper's is relative permittivity.
Substitutional donor/acceptor levels, equilibrium band bending, fixed space charge and the junction electric field
. Details. Poisson equation and widths. Let the depleted intervals be and . Fully ionized number densities correspond to electric charge densities , respectively. ThusThe factor converts a dopant concentration to a space-charge density. Requiring zero field in both neutral regions gives charge neutrality,With , direct integration gives the triangular fieldContinuity at the interface is the same neutrality condition. The field is negative throughout the depleted interval. Set . Its integral givesPotential continuity therefore requiresCombining it with neutrality yields the abrupt-junction depletion width and capacitance resultsThe more lightly doped side depletes farther, because equal and opposite space charges must be exposed.
Applied bias. Define positive as forward bias, raising the p-side terminal potential relative to the n-side terminal. It lowers the remaining barrier from to . Reverse bias has and raises that barrier. The same Poisson integration applies, with this replacement:Forward bias narrows the depleted region; reverse bias widens it. Under bias there need not be one equilibrium chemical potential across the device, so the equilibrium flat-level argument must not be reapplied unchanged. The barrier/width change is illustrated in the next figure.
Differential capacitance and electric charge sign. Put and . The signed p-side fixed electric charge per unit area isDifferentiating with respect to forward electric potential difference gives the positive capacitance per unit areaThe n-side electric charge is , so instead. If denotes a positive space-charge magnitude, the positive capacitance is for this forward-voltage convention. This resolves the sign implicit in the paper's positive . The total device capacitance is , where is its cross-sectional area.
Finite device and numerical sketch. For the symmetric device, and each side has thickness . Before full depletion,Using , the zero-bias width on each side is , less than . The total zero-bias capacitance is .
Full depletion occurs when , soAt larger reverse bias the depleted thickness cannot exceed . In the ideal fully depleted slab, incremental terminal electric charge changes the field uniformly through that fixed thickness, giving the full-depletion capacitance of a symmetric junction slabThus the idealized piecewise sketch over the specified range isIt is continuous at full depletion, rises through at zero bias, and has a formal inverse-square-root divergence as from below.
There are two physical limits to this extension. Once all dopants are exposed, their fixed space charge no longer increases, but the terminal electrodes can still acquire incremental electric charge; differentiating only the fixed ionized electric charge would incorrectly predict zero capacitance. Near , the depletion approximation itself fails as mobile carriers and forward injection become important, so the formal infinite endpoint is not a prediction of an actual infinite measured capacitance. The fully depleted plateau assumes ideal contacts and no breakdown, injection storage or extra series capacitance.
Past exam of the quantum condensed matter course of the University of Cambridge 2014 4 Solution Created 2026-10-18 Updated 2026-10-20
Nondegenerate carrier product. Assume three-dimensional parabolic energy bands near their extrema, spin degeneracy two, and no additional uncounted valley multiplicity. Near the conduction edge, a Boltzmann approximation to the Fermi-Dirac distribution givesAngular integration and the Gaussian radial integral yieldFor valence electron holes, the empty-state probability is . Measuring electron hole kinetic energy downwards from similarly givesThe factors two count spin once in each band. Multiplying cancels the chemical potential and proves the semiconductor mass-action law:In an intrinsic neutral semiconductor, . In a doped equilibrium semiconductor the same product holds under the stated nondegenerate assumptions, even when . Extra valleys or several valence branches must be included in the effective density-of-states factors rather than counted inconsistently.
Equilibrium junction. Put the p region on the left and the n region on the right. Before contact their majority carriers are electron holes and electrons, respectively. Diffusion initially sends electrons from n to p and electron holes from p to n. This leaves negative ionized acceptors on the p side and positive ionized donors on the n side, creating a depletion region and an electric field directed from n to p. At equilibrium this field balances diffusion, so the net electric current vanishes.
For a homojunction the gap remains constant while the conduction band and valence band edges bend downwards from p to n by . The equilibrium chemical potential is flat. Since , the electrostatic potential rises from p to n. The carrier profiles satisfyWith fully ionized nondegenerate dopants, the neutral p side has , , while the neutral n side has , . Thus the electron concentration rises across the junction and the electron hole concentration falls, with both small relative to the far-side majority densities in much of the depleted region. The ideal depletion approximation neglects these mobile populations when calculating the fixed space electric charge, but the actual equilibrium profiles are smooth.
Equilibrium band bending, a flat chemical potential and complementary electron/hole profiles across a homojunction
. Details. The built-in potential follows from these Boltzmann factors:There is no applied terminal bias; the internal electrostatic potential variation does not contradict a constant electrochemical potential.
Opposing carrier fluxes under reverse bias. Use for the magnitude of reverse bias and for reverse electric current, as in the PDF. The junction barrier increases by . The Shockley diode equation in that orientation can be writtenThe reverse-directed contribution is supplied by minority electrons on the p side and minority electron holes on the n side. They reach the depletion edge by diffusion and are swept across by the built-in field. The opposing contribution is associated with majority carriers thermally crossing the barrier in the forward direction; reverse bias suppresses it by the Boltzmann factor. At zero bias detailed balance makes the two equal, while at large enough reverse bias the opposing flux becomes negligible.
In the ideal neutral-region diffusion model,Here are minority-carrier diffusion coefficients, their diffusion lengths, and is junction area. The two terms inside this positive prefactor are the electron and electron hole contributions; both flow in the same reverse-current direction. This separates the two carrier-species contributions from the two opposing fluxes in the Shockley diode equation. Calling the saturation term a drift current refers to its passage across the depleted region, and does not eliminate the minority-carrier diffusion needed to supply it.
Reading the measured curves. At , the ideal equation gives , initially proportional to reverse electric potential difference. At , it approaches a plateau . The thermal electric potential differences at the three temperatures are about –, consistent with a rise at small reverse biases and near saturation at larger ones. Higher temperature produces a much larger plateau because thermal electron-hole excitation raises exponentially.
The lower-temperature curve has a noticeable residual electric potential difference dependence rather than a perfectly flat plateau. Depletion-region generation, surface leakage or other departures from the ideal diffusion model can contribute. The sharp upturn at the largest reverse electric potential differences is reverse breakdown, outside the unextended Shockley diode equation; the plot alone does not identify a unique microscopic breakdown mechanism. The original horizontal axis duplicates the final decade label, so a precise breakdown electric potential difference cannot be read reliably. Neither issue prevents estimating the gap from the intermediate-bias saturation region.
Band-gap estimate. Use plateau electric currents at a common intermediate reverse bias, away from both the small-bias rise and the breakdown upturn. Approximate readings are , –, and . Kelvin temperatures are required in the activation law.
For fixed effective masses, . If the remaining transport prefactor is approximately constant, extracting a semiconductor band gap from diode saturation current therefore usesUsing the widest temperature separation and the rounded readings givesNeglecting all algebraic prefactors and fitting instead gives about . These differ by roughly , a material correction on the graph's precision scale. Thus an honest graph-based conclusion isThe nonflat low-temperature plateau, rough electric current readings, unprovided temperature dependence of , and possible gap variation prevent a more precise extraction. If depletion-region generation dominated rather than the specified mechanism, its activation slope could involve a different energy scale; the displayed estimate explicitly uses the diffusion-dominated saturation model requested here.
Past exam of the quantum condensed matter course of the University of Cambridge 2016 3 Solution Created 2026-10-18 Updated 2026-10-20
mass as band curvature. In a periodic potential, a weakly forced electron is usefully described by a wave packet confined to one energy band. Its group velocity isDifferentiating the velocity givesThis effective-mass tensor describes the band response, not a change of the electron's bare rest mass. Along a principal direction, a steep upward curvature gives a small positive mass and a flatter curvature a larger one. Near a band maximum the electron curvature and effective mass are negative; the corresponding missing-electron description uses positive electron hole masses. Anisotropy produces distinct principal masses, and strong nonparabolicity makes them momentum dependent. The single-band semiclassical description assumes fields weak and slowly varying enough to avoid substantial interband transitions.
Lattice symmetry and Bloch's theorem. Use the active spatial translation operator . A lattice-periodic scalar potential satisfies , while the kinetic term is translation invariant. Therefore . The lattice translations also commute with one another, so they can be diagonalized simultaneously with , including within a degenerate energy subspace.
For a common eigenstate, write . Unitarity gives , and the group law gives . On primitive Bravais vectors , choose . Every lattice vector is an integer combination of these generators, henceThe vector is defined modulo a reciprocal lattice vector. The band index labels the different energy eigenstates with the same translation character. Define . The phase factors cancel under a lattice translation, proving Bloch's theorem in its usual form:This is the Translation-character proof of Bloch theorem; the commutator guarantees a basis of such states, even when an arbitrary superposition of different translation characters is not itself a translation eigenstate.
Periodic Hamiltonian. Acting once with momentum gives . Applying it again and cancelling the common plane-wave factor yieldsThe Bloch Hamiltonian acts on lattice-periodic functions in a unit cell. Expanding its square separates a zero-momentum Hamiltonian, a term linear in and an identity term quadratic in .
Expansion about the zone centre. Let , , and normalize all these states using a unit-cell inner product. For the real scalar Hamiltonian in the question, a nondegenerate zone-centre eigenfunction can be chosen real. Thenbecause opposite unit-cell faces cancel. Equivalently, time-reversal symmetry forbids a nonzero electric current in this nondegenerate spinless state. This explains why no linear energy term appears; it should not simply be omitted without a symmetry or extremum argument.
The first-order energy shift is therefore . In the second-order sum the quadratic term is proportional to the identity and has no off-diagonal matrix elements. Only the linear momentum vertex contributes. Second-order nondegenerate perturbation theory gives the momentum matrix-element expansion of band energyHermitian operator makes the two reciprocal matrix elements complex conjugates. All other periodic eigenstates at enter the sum. The remainder is even because time-reversal symmetry gives near this isolated state. At a degeneracy the denominators signal the need for degenerate perturbation theory instead.
mass ratio and the printed formula. Write . Differentiating the quadratic energy yieldsFor a specified unit direction , the resulting scalar mass ratio isIn an isotropic three-dimensional band, averaging equivalent directions givesCoupling to lower bands contributes positively to inverse mass; coupling to higher bands contributes negatively. Their signs and matrix elements determine the actual curvature.
The original PDF prints . Taken literally as a three-dimensional Laplacian, this misses a factor of three for an isotropic scalar mass. The correct identities areThe printed expression would return even for the free dispersion . It is correct in one dimension, or if its second derivative is interpreted directionally. For completeness, its literal three-dimensional trace ratio would instead be ; that is the trace of the dimensionless inverse-mass tensor, not the usual scalar .









