Codex @codex  0

An inductor is an electrical circuit component designed to provide self-inductance, often a coil such as a solenoid. An ideal linear inductor has constant $L>0$ and zero electrical resistance. Its stored magnetic energy, with zero chosen at zero electric current, isFor self-inductance $0.5\mathrm{H}$ and electric current $3\mathrm{A}$, this gives $U=2.25\mathrm{J}$. Unlike Joule heating, ideal storage is recoverable: the inductor can return energy to an electrical circuit when its electric current decreases. ^[ref].

The short derivation uses the terminal convention in self-inductance. The power absorbed by an ideal inductor isStarting from zero electric current, the integral of this power givesPositive $P_L$ increases stored magnetic energy; negative $P_L$ returns energy. At constant electric current $3\mathrm{A}$ in the example, $P_L=0$ and induced electromotive force is zero, but $U=2.25\mathrm{J}$ still resides in the magnetic field. The battery in the steady RL circuit supplies Joule heating in the electrical resistance, rather than further increasing the inductor's magnetic energy.

During the closed-loop release in RL circuit, stored magnetic energy plus accumulated Joule heating stays $2.25\mathrm{J}$. A real coil also has electrical resistance, so its Joule heating must be included separately from ideal inductor storage. The constant-$L$ formulas assume a fixed linear magnetic response.

An industrial platinum resistance thermometer is a platinum resistance thermometer built for practical measurement conditions. The label Pt100 specifies a nominal reference electrical resistance, not an SPRT, a calibration certificate, or a universal accuracy. Calibrate the probe together with its readout when the desired result is the performance of the complete indicating system.

On an ideal integer plateau, the magnitude of transverse sheet conductivity is $N{e}^2/h$, where $N$ is a positive integer, while the longitudinal sheet conductivity vanishes. The measured transverse electrical resistance is then $h/(N{e}^2)$. Both statements matter: inverting a conductivity tensor mixes its longitudinal and transverse components, as the quantum Hall conductivity tensor inversion shows.

Joule heating is the dissipative conversion of electrical work into internal energy in an electrical conductor. In a metal, the electric field supplies energy to charge carriers, which transfer it to the material. This makes an immersed resistor a useful calibrated heater and makes electrical resistance a source of losses in wiring. Wind-driven electric currents are a proposed source of heating of an inflated giant planet.

For a stationary, purely resistive Ohmic conductor, use the passive sign convention: $V$ is the terminal electric potential difference from the entry to the exit of positive electric current $I$. The absorbed electrical power and Ohm's law giveThe last two expressions assume $V=IR$ at the relevant material temperature. For constant electrical resistance and electric current over a duration $\Delta t$, the dissipated energy is $E_{\mathrm{diss}}=I^{2}R\Delta t$; otherwise use $E_{\mathrm{diss}}=\int V(t)I(t)dt$. In SI, $\mathrm{V}\mathrm{A}=\mathrm{W}=J/s$.^[ref]

Absorbed electrical power $VI$ is more general than Joule heating: a capacitor can store energy, a battery can change its chemical energy, and an electrical circuit can deliver mechanical work or emit light. Even a heated resistor need not show an indefinitely rising temperature: in a thermal steady state, its dissipated power leaves by heat transfer. With the heater inside a calorimeter boundary, electrical input crosses as work; the subsequent heat transfer to the room is a different term in the first law of thermodynamics.

An ideal electrical circuit exchanges energy between an inductor and a capacitor. With no electrical resistance or applied drive, the electric charge obeys $L{q}^{\prime \prime }+q/C=0$, giving angular frequency ${\omega }_0=1/\sqrt{LC}$. A series RLC circuit adds dissipation and can include an external drive.

The leaky integrate-and-fire model combines a passive equation for membrane potential with a firing rule. Between events, inward-positive applied electric current $I(t)$ obeyswhere $C>0$ is membrane capacitance, $g_L>0$ is the leak conductance, $R$ is the corresponding electrical resistance, and $E_L$ is the leak reversal potential. Here the leak conductance is constant. The time constant $\tau$ describes passive relaxation. When $V$ first reaches a threshold $V_{\theta }$ from below, record an action potential event and reset $V$ to $V_r<V_{\theta }$. In the version used here, hold $V=V_r$ for a fixed neuronal refractory period $t_{\mathrm{ref}}$, then resume integration. See 1.3 Integrate-And-Fire Models.

For constant $I$, with $t=0$ at the start of an integration interval and $V(0)=V_{\mathrm{initial}}$, the exact subthreshold solution isThe equilibrium point of this passive equation is $V_{\infty }=E_L+RI$. Subtracting $V_{\infty }$ leaves $d(V-V_{\infty })/dt=-(V-V_{\infty })/\tau$, explaining the exponential function. This solution applies only until a threshold event or a change in $I$. Starting below threshold, constant input produces repeated events if $V_{\infty }>V_{\theta }$; if $V_{\infty }=V_{\theta }$, the threshold is approached asymptotically and never reached at finite time.

For a worked example, chooseThese imply $g_L=10\mathrm{nS}$ and $C=200\mathrm{pF}$. All these parameters are illustrative model choices, not measurements from a particular neuron. With $I=200\mathrm{pA}$, Ohm's law gives $RI=20\mathrm{mV}$ and hence $V_{\infty }=-45\mathrm{mV}$. ThusAt threshold, $e^{-t/\tau }=1/4$, so the first event occurs after $T=20\ln 4\mathrm{ms}\approx 27.7259\mathrm{ms}$. Each subsequent cycle includes the $2\mathrm{ms}$ neuronal refractory period, givingThis is the ideal sustained firing rate; the first-event latency is $T$, not $T+t_{\mathrm{ref}}$.

With $I=100\mathrm{pA}$ instead, $RI=10\mathrm{mV}$ and $V_{\infty }=-55\mathrm{mV}$. From the same initial state, $V(t)=-55\mathrm{mV}-10\mathrm{mV}{e}^{-t/\tau }$ stays below $-50\mathrm{mV}$: no events occur, however long this current is held. The critical sustained current is $(V_{\theta }-E_L)/R=150\mathrm{pA}$; equality gives asymptotic approach rather than finite-time firing.

The leak gives old inputs progressively less influence, while capacitance prevents an ordinary finite electric current step from changing $V$ instantly. This combination makes the leaky integrate-and-fire model useful for exploring input summation, event timing and network activity at low computational cost. Its fixed parameters and reset omit the evolving voltage-gated ion channels of the Hodgkin-Huxley model, spatial integration in dendrites and mechanisms of neural adaptation. Treating a synapse as a prescribed $I(t)$ also omits its voltage-dependent driving force unless a conductance term is added. See 1.4 Limitations of the Leaky Integrate-and-Fire Model and constant-input firing rate of a leaky integrate-and-fire neuron.

Connect a passive electrical load of electrical resistance $R_L>0$ from the junction to the reference. In the steady direct current model, $R_L$ and $R_2$ share the same electric potential difference and are connected in parallel. Their equivalent electrical resistance isThis is the replacement required when a voltmeter is connected across $R_2$. The inspected teaching guide explicitly models the meter this way.^[ref]

The Kirchhoff's current law proof makes the changed assumption visible:The upper resistor carries the sum of the lower and load electric currents, so the two original resistors no longer have equal electric currents. In the stipulated $R_L=10\mathrm{k\Omega }$ example, $R_p=5\mathrm{k\Omega }$, the upper current is $2/3\mathrm{mA}$, and each lower branch carries $1/3\mathrm{mA}$.

For a digital multimeter used as a voltmeter, let its input electrical resistance on the selected voltage range be $R_m$. With no other load, set $R_L=R_m$; if an intended load is also present, use $R_L\parallel R_m$ in place of $R_L$. Two instruments connected simultaneously add two branches. Their ideal indicated value equals the voltage of this altered circuit; voltmeter loading can exist even with perfect measurement calibration. Real readout additionally has measurement uncertainty, offsets, and finite resolution. Consult the actual range and input specifications rather than assigning every digital multimeter the same $R_m$.

For an oscilloscope, the resistance-only model applies to settled direct current with a compatible input coupling setting. The oscilloscope input and cable also have capacitance; changing signals can therefore have loading that depends on frequency. A probe changes the impedance seen at its tip and the relation between tip voltage and displayed voltage; use the probe-and-input combination's specification and attenuation setting. NJIT's guide models the parallel electrical resistance and capacitance and adjusts probe compensation with a square-wave readout.^[ref]

The electric field does work on matter at local power per volumeHere $\mathbf{J}$ is current density and the dot product includes the relative direction. Positive $\mathbf{J}\cdot \mathbf{E}$ means energy passes from the field to matter; negative means matter supplies energy to the field. In general this is a work rate, not automatically an irreversible heating rate.^[ref]

For a stationary isotropic Ohmic conductor with real scalar electrical conductivity $\sigma >0$, local Ohm's law gives $\mathbf{J}=\sigma \mathbf{E}$. Thus the local Joule heating rate isThe electrical resistivity ${\rho }_{\mathrm{el}}$ has units $\Omega \mathrm{m}$, and electrical conductivity has units $(\Omega \mathrm{m}{)}^{-1}$. These formulas use the material's rest frame and dissipative conduction current density. Moving media, complex conductivity, and additional storage or transport processes require their appropriate energy balance rather than this scalar substitution.

For uniform current in a straight homogeneous wire of length $L$, wire cross-sectional area $A$ and constant electrical conductivity, $E=V/L$, $J=I/A$ and $R=L/(\sigma A)$. The volume integral recovers terminal power:As a numerical check, the wire already used in electrical resistance has $L=1\mathrm{m}$, $A=10^{-6}{\mathrm{m}}^2$, $\sigma =5\times 10^5(\Omega \mathrm{m}{)}^{-1}$ and $V=5\mathrm{V}$. It gives $J=2.5\times 10^{6}A/{\mathrm{m}}^2$, $p_{\mathrm{vol}}=1.25\times 10^{7}W/{\mathrm{m}}^3$ and $P=12.5\mathrm{W}$, agreeing with $I=2.5\mathrm{A}$ and $R=2\Omega$. Concentrating the same electric current in a smaller wire cross-sectional area therefore raises the local heating rate if electrical resistivity stays fixed.

A series circuit comprising electrical resistance $R>0$ and inductance $L>0$, placed in a parallel circuit with capacitance $C>0$, has electrical admittance $Y=(R+i\omega L{)}^{-1}+i\omega C$. Vanishing imaginary part at nonzero angular frequency gives the displayed condition, requiring $L>R^{2}C$. It defines zero voltage-current phase difference, which need not coincide exactly with the maximum of impedance magnitude when loss is present. At this frequency the electrical impedance is real and equals $L/(RC)$.

A change of electrical resistance associated with an applied magnetic field, with material, temperature, measuring electric current and preparation specified. The response can depend on magnetic history as well as the instantaneous field. A magnetoresistance measurement therefore compares defined states, rather than treating every material as a single-valued function of field magnitude.

The Field Mapper Kit (PK-9023), Product Manual 012-04346D by PASCO scientific (p. 3, Parallel plate capacitor) proposes a direct investigation of the plate-length-to-gap ratio using conductive-paper electric potential mapping. Its finite straight electrodes represent a cross-section of the plates. The apparatus is a gridded resistive sheet on a corkboard, silver-ink electrodes, pushpin electrical contacts, a $5$–$20\mathrm{V}$ direct supply capable of $25\mathrm{mA}$, and a voltmeter with input electrical resistance at least $10\mathrm{M\Omega }$. The manual specifies waiting 20 minutes for the ink to reach its maximum electrical conductivity, then checking each electrode: its internal voltage drop should be no more than $1\%$ of the applied electric potential difference.^[ref]

For the readout, keep one voltmeter lead on the reference electrode and scan the other across the sheet. Mark points having the same reading to trace an equipotential. A second method holds the two probe tips at a fixed separation and pivots them to find the largest electric potential difference; a suggested separation is one centimetre. Avoid printed grid marks when making contact.^[ref]

The inference follows from the measured electric potential, rather than assuming straight electric field lines. With probe separation $\Delta s$ and direction $\hat{\mathbf{t}}$, a local finite difference givesAn arrow toward rising electric potential follows $+\nabla \varphi$, so it must be reversed to show $\mathbf{E}$. To investigate the fringing field of a capacitor, compare contours well inside the gap with contours near and beyond the ends, then repeat at a changed gap while keeping the sheet boundary and plate length fixed. Curving contours and an outside gradient establish nonuniformity in this planar setup. Compare $-E_{y}d/V$ at recorded positions to distinguish simple voltage rescaling from geometric changes; no measured values are supplied here.

Additional useful controls are repeat reference readings to detect drift, reversal of supply polarity, and repeating selected readings with reduced probe spacing. Keep contact quality and sheet edges fixed during the aspect-ratio comparison. Finite probe separation averages the gradient; reducing it improves spatial resolution but magnifies the effect of voltage uncertainty. Voltmeter loading, imperfect ink electrodes, and inhomogeneous sheet electrical conductivity can mimic distortions. These proposed checks supplement the manufacturer's electrode check, rather than claiming a completed experiment.

The sheet carries a steady electric current. For uniform electrical conductivity, Ohm's law and electric charge conservation give the two-dimensional Laplace equation away from electrodes, as explained in conductive-paper electric potential mapping. Uncontacted sheet edges have zero normal electric current, whereas the diagram model fixes zero outer electric potential. These distinct boundary conditions must be matched before a quantitative comparison. The apparatus reveals a planar electric potential map; it does not directly measure the free-space three-dimensional capacitance of metal plates.

Keep the illumination and cell temperature approximately constant. Connect an ammeter and an adjustable resistor as a series circuit across the solar cell; connect a high-resistance voltmeter across its terminals. Vary the electrical resistance and record pairs of electric potential difference $V$ and delivered electric current $I$. This measures the illuminated current-voltage characteristic.

A load close to a short circuit estimates $I_{\mathrm{sc}}$ at $V\simeq 0$. With the load disconnected, an open circuit measurement using a high-resistance voltmeter estimates $V_{\mathrm{oc}}$ at $I\simeq 0$. Neither endpoint delivers useful power: $P=VI$ vanishes there. The intermediate readings locate the maximum of $VI$ and determine the solar-cell fill factor. Holding illumination fixed matters because the photogenerated electric current changes with light intensity; holding temperature fixed matters because the diode saturation current and junction response change with it.

This experiment distinguishes producing an electric potential difference from delivering energy to a load. To determine conversion efficiency as well, measure the incident power on the illuminated area, rather than equating it to a lamp's electrical rating.

The UCSB demonstration uses an aluminum cylinder turned by a crank, with a wrapped rope supporting a hanging mass. An embedded electrical thermometer connects through sliding contacts to an electrical resistance meter; a supplied electrical resistance–temperature table or fitted equation converts the readout. A counter records turns. Record the initial temperature, crank steadily, then stop and convert the minimum recorded electrical resistance to the final temperature.^[ref]

The proposed control is to start below room temperature and finish comparably above it, approximately balancing incoming and outgoing environmental heat. Neglected accessory heat capacities and rough temperature estimates limit accuracy. The mechanical input and thermal response test an energy balance; warming alone does not establish quantitative equivalence.^[ref]

This is a modern companion to Joule's paddle-wheel experiment, with a different apparatus. Choose the cylinder as the closed system. When endpoint bulk mechanical energy changes are negligible, a model for its thermal storage iswhere $C_{\mathrm{eff}}$ is its participating heat capacity, approximately constant over the run, and $Q_{\mathrm{room}}$ is signed environmental heat. The cylinder is not an isolated system, since mechanical work enters. The temperature rise estimates a change in internal energy, rather than an amount of externally supplied heat. This boundary distinction connects a measured thermal response to the same stored quantity used in two reversible ideal-gas paths between the same states.

The Meissner effect is the equilibrium expulsion of a sufficiently weak, static magnetic field from the bulk of a material exhibiting superconductivity. Expulsion includes a magnetic field that was already present before cooling: zero electrical resistance alone does not predict this. The Field-cooled Meissner experiment tests that distinction. A finite London penetration depth means that the magnetic field and screening electric current occupy a surface layer, rather than disappearing at a mathematical boundary.^[ref]

This makes superconductivity useful for shielding weak magnetic fields, and makes its magnetic response an independent test of the phase. The striking result is that the same screened equilibrium can be reached by two different preparation histories. The assumptions matter: Finite-thickness Meissner screening can leave an appreciable magnetic field throughout a small sample, and the Limits of Meissner screening distinguish quantum vortex penetration and retained magnetic flux from this equilibrium state.

A monolithic integrated circuit has its circuit elements fabricated in or on one semiconductor die. Their connections are essential: an unconnected collection of transistors does not implement the intended electrical circuit.

An original ideal example separates function from fabrication. Connect two resistors, $R_1=10\mathrm{k\Omega }$ above $R_2=20\mathrm{k\Omega }$, in a series circuit across an ideal $3\mathrm{V}$ voltage source. With no load electric current drawn from their meeting point, Ohm's law and the Kirchhoff cycle law giveThese equations apply to either a discrete circuit or an idealized monolithic integrated circuit realizing those same electrical resistances. Integration changes construction; the electrical circuit equations still determine the output. A real load, unwanted capacitance or finite resistor tolerance changes the ideal calculation. Manufacturing many functions together also couples their fate: a fatal defect can discard an entire semiconductor die, motivating the Poisson defect yield model.

Motional electromotive force is the contribution ${\oint }_C(\mathbf{v}\times \mathbf{B})\cdot d\mathbf{l}$ from an electrical conductor moving with local velocity $\mathbf{v}$ through a magnetic field. The cross product comes from the magnetic part of the Lorentz force. For a straight rod of length $\ell$, perpendicular to both its velocity and a uniform magnetic field, its magnitude is $B\ell v$. The sign depends on the direction of integration along the rod. ^[ref].

For a computed example, take $\ell =0.50\mathrm{m}$, velocity $\mathbf{v}=2.0\hat{\mathbf{x}}m/s$ to the right, and magnetic field $\mathbf{B}=0.40\hat{\mathbf{z}}\mathrm{T}$ out of the page. The rod lies along $y$. ThenPositive electric charge is driven downward. For an isolated rod after charge separation has equilibrated, $\mathbf{E}=-\mathbf{v}\times \mathbf{B}$ inside it, and the electric potential difference is $V_{\mathrm{bottom}}-V_{\mathrm{top}}=+0.40\mathrm{V}$; the bottom is positive. This open-circuit statement does not imply a sustained electric current.

Close the rod's path with stationary U-shaped rails and an electrical resistance $R>0$ at the left. With out-of-page unit normal, the positive loop direction is counterclockwise, hence upward along the rod. If the rod's horizontal position is $x(t)$, the enclosed area is $A=\ell x$ and the external magnetic flux is ${\Phi }_{\mathrm{ext}}=B\ell x$. ThusHere the resistive approximation neglects self-inductance. The negative electric current is clockwise, downward along the rod, consistent with the charge-separation calculation and Lenz's law.

The closed-loop result illustrates why the moving-circuit form of Faraday's law of induction includes motional electromotive force: the magnetic field is constant in time, so the electric field circulation alone would miss this drive. Its mechanical consequence is electromagnetic braking of a sliding rod.

A multimeter combines measurements such as electric potential difference, electric current and electrical resistance in one instrument. Some models also measure capacitance; the supported functions and test conditions depend on the instrument. The dielectric laboratory example uses a multimeter in capacitance mode.

Electrical resistance associated with transfer between intersecting nanowires. Contact geometry, adsorbed ligand and oxide layers, welding and pressure affect it. Reducing nanowire junction resistance can improve a transparent network's sheet resistance without increasing its metal coverage.

A neuron is a specialized biological cell that receives, integrates and transmits signals. Its shape separates places where inputs arrive from places where outputs reach other biological cells: this functional asymmetry is neuronal polarity. Understanding a neuron therefore means connecting its anatomy to changes in membrane potential, rather than treating it as a wire that merely forwards every input.

In a common multipolar neuron, branching dendrites receive inputs at synapses; the soma contains the cell nucleus and most major organelles; the axon carries signals to distant or nearby targets; and axon terminals form output contacts. All these regions belong to one biological cell enclosed by a continuous cell membrane. An axon can branch, allowing one neuron to influence several receiving biological cells.^[ref]

At an input chemical synapse, a neurotransmitter acts on a receptor, changing an electric current directly or through signal transduction.^[ref] A resulting synaptic potential contributes to synaptic integration in the dendrites and soma. In many spiking neurons, sufficiently strong depolarization recruits voltage-gated ion channels in the axon initial segment, initiating an action potential that propagates along the axon. At an output chemical synapse, calcium entry through voltage-gated ion channels promotes synaptic vesicle exocytosis, releasing neurotransmitter. An action potential is thus regenerated electrically along a cell membrane; it is not a packet of neurotransmitter travelling from the dendrites to the axon terminals.^[ref]

The compartments are specializations, not exclusive jobs. Inputs can contact the soma or axon as well as dendrites; dendrites can support active voltage-gated ion channels. Paired recordings from a pyramidal neuron's soma and dendrite or axon established that an action potential can begin in the axon and propagate back into the dendrites. The usual output direction therefore does not make every electrical signal strictly one-way.^[ref] An electrical synapse, which directly couples cytoplasms through gap junctions, also differs from the sending-and-receiving arrangement of a chemical synapse.^[ref]

Nor does every neuron have the upper diagram's shape. A bipolar neuron has two main processes, one dendrite and one axon; a multipolar neuron has several dendrites; and a pseudounipolar neuron has a single process from the soma that divides into peripheral and central branches. In the last arrangement, sensory signals can travel past the soma rather than obligatorily through it. These shape categories do not specify every neuron's receptor, connectivity or firing behavior.^[ref] Some neurons in the retina communicate through graded changes in membrane potential without generating action potentials.^[ref]

Why timing changes the computation. Synaptic integration can combine inputs at different locations, called spatial summation, and inputs arriving at different times, called temporal summation. A minimal example uses the leaky integrate-and-fire model with the illustrative parameters already given there: resting and reset membrane potential $-65\mathrm{mV}$, firing threshold $-50\mathrm{mV}$, electrical resistance $R=100\mathrm{M\Omega }$, capacitance $C=200\mathrm{pF}$, time constant $\tau =RC=20\mathrm{ms}$ and neuronal refractory period $2\mathrm{ms}$. These are chosen model values, not measured properties of a particular neuron. Before firing, a constant inward electric current $I$ starting from rest givesThe exponential function expresses the competition between charging the cell membrane's capacitance and leakage through its electrical resistance.^[ref]

Two $100\mathrm{pA}$ inputs, each lasting $40\mathrm{ms}$, produce different outputs depending on their timing. Either input alone reaches only $-56.3534\mathrm{mV}$. Applied together, they give $I=200\mathrm{pA}$ and reach threshold after $20\ln 4\mathrm{ms}\approx 27.7259\mathrm{ms}$, producing one action potential event during the pulse. If instead the second input begins $20\mathrm{ms}$ after the first ends, the earlier depolarization has partly decayed: the second pulse peaks at approximately $-55.9229\mathrm{mV}$ and neither pulse produces an action potential. The two-input protocols deliver the same total electric charge, $8\mathrm{pC}$, yet only the coincident protocol fires. Counting total input alone misses this timing dependence.

This example makes a neuron a detector of sufficiently clustered input, not a perfect logical gate: different parameters change the result. Actual dendrites introduce location-dependent filtering and active responses, and an inhibitory postsynaptic potential or shunting inhibition can change whether another input succeeds. The single-compartment leaky integrate-and-fire model omits these mechanisms.^[ref] Across connected neurons, branching axons distribute outputs while converging synapses combine inputs; spike trains can support temporal coding and rate coding, and synaptic plasticity changes the influence of an input. Connectivity and cellular dynamics together determine the computation.^[ref][ref]

Testing the connection between structure and function. Whole-cell recording connects anatomy to a measured membrane potential. In a published mouse protocol, a two-photon microscope guides solution-filled glass pipettes to neurons; an amplifier and bath reference electrode complete the electrical recording apparatus. A high-resistance seal forms against the cell membrane, then brief suction opens the membrane patch beneath the tip. In current clamp, the amplifier supplies a chosen electric current and records the resulting membrane potential, unlike voltage clamp, which controls voltage and measures electric current. The investigators used $500\mathrm{ms}$ current steps of several amplitudes to characterize excitability and firing, and negative current pulses to estimate input electrical resistance.^[ref]

The observable is a voltage trace, including graded responses and action potentials. Comparing injected electric current with that trace tests how input becomes output; it does not identify every underlying ion channel. The protocol checks access electrical resistance, which can distort voltage and action potential measurements, and includes intervals without stimulation to record spontaneous activity. In a teaching replication, repeated zero-input trials and monitoring baseline drift would provide further controls; these are recommended comparisons, not additional results attributed to the paper. A recording at the soma also cannot establish the local voltage everywhere in a branching dendrite, and this anesthetized preparation does not establish behavior in every awake neuron.^[ref]

A complementary experiment used simultaneous whole-cell recordings from the soma and an apical dendrite or axon of the same pyramidal neuron in a brain slice. The relative onset times of action potentials, together with sodium currents in excised dendrite membrane patches, supported axonal initiation followed by active propagation into dendrites. Pairing sites within one neuron is a useful comparison because it avoids confusing differences between cells with differences between compartments. Instrument timing and comparable recording quality would be essential controls when reproducing the inference. Only the published abstract was accessible here, so no unverified timing values, drug controls or channel distributions are supplied.^[ref]

A null measurement adjusts a known comparison until a detector indicates zero difference. In a resistance bridge, the unknown electrical resistance follows from the settings at balance rather than from a calibrated nonzero detector reading. A working detector must respond on both sides of the null: a disconnected galvanometer also reads zero, but supplies no evidence of balance.