A useful original model treats the thermopile absorber as one approximately uniform temperature with heat capacity , connected to a fixed reference temperature by thermal conductance . Both parameters are positive constants here. Let be an added absorbed power above the initial background. Linearize the outgoing heat transfer about that background. With measured from an initial state having , conservation of energy gives the first-order linear differential equation
The left side is the rate of stored energy; the two terms on the right are added power and outgoing heat transfer. The effective thermal conductance can include several paths, rather than just heat conduction along the wires. The model assumes a stable reference, negligible electrical loading, a common absorber temperature, and changes small enough for constant parameters.
For a step from zero to constant at , subtract the steady solution . The difference obeys exponential decay, so the initial condition fixes
The time constant has units . With the same constructed and , choose , and . Then
At one time constant, the response is of its final value: . Reaching requires . A voltmeter read too soon therefore underestimates the steady signal even when its electrical calibration is perfect.
Figure 1. . Original model curves for added absorbed power , and relative Seebeck coefficient . The solid curve uses and , giving time constant and final voltage . The dashed comparison halves only : final voltage doubles, but so does the time constant. Neither curve is an experimental observation. Details.
The steady ratio is in this constructed model. Halving thermal conductance doubles this ratio but also doubles the time constant if heat capacity stays fixed. Reducing heat capacity alone speeds the response without changing its steady value. Increasing gives a larger signal only at fixed individual temperature differences: adding legs can also change thermal conductance, heat capacity and electrical resistance. The algebra identifies coupled design choices, rather than predicting a particular manufactured detector.
A finite electrical resistance produces Thermal electrical noise. For nearly uniform absolute temperature and effective measurement signal bandwidth , its root mean square open-circuit voltage is
Here is the Boltzmann constant. Thermal electrical noise in the sensing element is an important contribution, and the signal bandwidth enters its voltage variance.[ref] If identical pairs have fixed electrical resistance and fixed , then : the signal grows as while this noise grows as . The resulting signal-to-noise ratio grows only as under those assumptions. Reference temperature drift, environmental electromagnetic radiation, and meter noise remain separate limits; reducing signal bandwidth trades fast information for less integrated electrical noise.
Thévenin's theorem Created 2026-10-13 Updated 2026-10-14
Thévenin's theorem replaces the terminal behavior of a linear resistive circuit by an ideal voltage source in series with a Thévenin resistance, whenever its terminal electric potential difference is a well-defined affine function of the delivered electric current. Fix terminals , write , and take positive out of the network at into the electrical load, returning through . Then
The open-circuit voltage is the intercept at ; is the slope. Thus two parameters predict what happens when many different electrical loads are connected. The Wheatstone bridge detector loading calculation uses precisely this replacement to find the detector reading even when the bridge's two voltage dividers interact through its detector.
For example, a ideal voltage source with above and below a voltage divider junction supplies and at that junction relative to the lower terminal. Attaching a electrical load reduces its voltage to and draws . The equivalent explains why an unloaded divider ratio alone cannot predict a loaded output.
Figure 1.
A 12 V voltage divider and its 8 V Thévenin equivalent feed the same load
. Original calculated example: the left circuit has and divider arms; the right circuit has an ideal voltage source and series Thévenin resistance. Both use and delivered electric current from into the same electrical load. Dashed boundaries identify what is replaced. Source. Details.
The equivalence concerns the chosen terminals, including the power delivered there. It does not identify internal branch electric currents or internal Joule heating. At open circuit the original divider still draws from its supply, while the equivalent's series branch carries no electric current. [ref]
With the passive sign convention applied to the network, its entering electric current is , and the same relation becomes . The electrical load uses the passive sign convention with entering electric current , so it absorbs power . A positive delivered electric current therefore produces a voltage drop for positive ; changing the reference direction without changing the equation would give the wrong sign.
The reason is linearity of Ohm's law, Kirchhoff's current law, Kirchhoff's voltage law, and the constitutive relations of any linear dependent electrical sources. Solve once at with the independent electrical sources present. Subtract this solution from a solution with prescribed delivered electric current : the fixed independent electrical sources cancel, leaving a homogeneous linear network whose terminal voltage change is proportional to . This is a short superposition principle argument for an affine function; the fixed offset need not vanish.
The qualification about a well-defined response matters. An ideal voltage source alone has . An ideal nonzero current source alone constrains and does not have a finite open-circuit voltage or a representation with finite coefficients. Linear dependent electrical sources can give negative resistance, and singular ideal networks may fail to have a unique finite response. Neither a finite nor a strictly positive passive follows merely from calling an electrical circuit linear. [ref]
Thomson cross-section Created 2026-10-18 Updated 2026-10-25
A free nonrelativistic charge driven by a weak plane electromagnetic wave has peak acceleration . Its time-averaged Larmor formula power is . Divide by incident light intensity to obtain the displayed cross section, independent of frequency. For an electron, it is . The approximation assumes negligible Compton recoil kinematics and small driven velocity compared with the speed of light.
Thrust Created 2026-10-18 Updated 2026-10-20
A propulsive force exerted on a body by an engine or another momentum-transfer mechanism. In a vehicle moving through a fluid, its direction need not coincide with the vehicle's actual velocity, and a transverse component can steer the motion. The component along the velocity contributes mechanical power ; a purely transverse component changes direction without doing instantaneous work. Rocket thrust is one particular mechanism and includes momentum carried by expelled material.
Total internal reflection Created 2026-09-29 Updated 2026-10-18
Total internal reflection occurs when a wave travels from higher to lower refractive index above the critical angle for total internal reflection, leaving no propagating transmitted plane electromagnetic wave normal to the interface.
At an infinite planar interface, total internal reflection returns all incident normal power in the reflected plane electromagnetic wave. Assume homogeneous dielectrics with isotropy, linearity, no dielectric loss, magnetic permeability , and positive real refractive indices . Above the critical angle for total internal reflection, both TE polarization and TM polarization have unit optical reflectance despite the external evanescent wave.[ref]
This makes total internal reflection useful for guiding light in an optical fiber: suitable internal incidence angles keep energy inside successive boundaries. Its more surprising feature is that perfect optical reflectance coexists with an external electric field. The evanescent field in total internal reflection can interact with a nearby object, as the frustrated total internal reflection experiment demonstrates.
For an original idealized example, choose , at vacuum wavelength . At angle of incidence , Snell law for electromagnetic waves gives an angle of refraction , so a transmitted light ray still emerges. At , its direction becomes tangent to the boundary. At , the proposed sine of a real angle of refraction would be : the transmitted wavevector must instead have an imaginary normal component. These are predictions for the stipulated media, not measured properties of a particular block.
Figure 1.
Constructed ray geometry just below, at, and above the critical angle for refractive indices 1.5 and 1; arrows indicate directions rather than relative powers
. Details.
A real semicircular-block experiment isolates this threshold. The University of Maryland laboratory instructions place a laser, motor-driven rotation stage and photodetector together; an aperture limits the detector voltage. The semicircular block is centered on the rotation axis, with the photodetector aligned along its flat face. The instructions identify a strong grazing-beam signal and a weaker signal just before the critical angle for total internal reflection. The readout is detector voltage versus stage angle. Retracing the incident laser beam identifies normal incidence for alignment.[ref]
The semicircular shape supplies a geometric control: a light ray passing radially through the curved face enters at normal incidence, avoiding additional entrance refraction. The weaker signal near the flat face locates a limiting angle of refraction; a vanishing remote-detector signal alone would not establish that the external electric field vanishes. Beam width and alignment limit angular resolution; no measured threshold or decay depth is supplied.[ref]
Transformer (electrical engineering) Created 2026-10-18 Updated 2026-11-05
An electrical transformer transfers energy between electromagnetic coils through electromagnetic induction. A changing shared magnetic flux produces an electromotive force in each coil. In the ideal model, both coils link the same flux ; for and turns, Faraday's law of induction gives induced voltages proportional to and . Their relative signs depend on the winding orientations.[ref]
For sinusoidal operation, the ideal root mean square voltage magnitudes satisfy
The ideal lossless model also conserves transferred power. With negligible excitation electric current, its electric current magnitudes obey . For a load electrical impedance , combining the voltage and electric current ratios gives the input electrical impedance
Thus an electrical transformer changes the voltage-current relationship seen by a source as well as the voltage.[ref]
For an ideal 10:1 turns ratio, a 230 V sinusoidal input produces 23 V at the secondary. A 23 ohm resistive load draws 1 A, corresponding to 0.1 A at the primary: both sides transfer 23 W. These are ideal-model calculations. Winding electrical resistance, magnetic hysteresis, eddy currents and incomplete shared flux introduce losses or departures from those ratios in a real electrical transformer. A constant flux produces no sustained induced secondary voltage.
Transistor 2026-10-18
A transistor is a semiconductor device in which an input controls an output electric current. Used with biasing and an electrical load, it can form an electronic amplifier or a switch. Its power gain comes from an external supply: the input signal controls the conversion of supplied energy into output signal power.
The point-contact transistor makes the idea tangible: two nearby contacts interact through one piece of semiconductor. A bipolar junction transistor instead uses two p-n junctions and a thin intervening region. The distinction matters both for the history and for choosing a physical model.
An original teaching model exposes the roles of input loading, output loading and the supply. Choose a small-signal model with positive input electrical resistance , transconductance , and output electrical resistance . Its controlled output current source draws from the output node toward the reference node. This chosen sign gives an inverting voltage gain; it is not the historical contact circuit's sign convention.
Assume a fixed operating point, negligible reverse coupling, a frequency range where coupling capacitors pass the signal, and negligible other capacitances and transit delays. A collector resistor connects the output to a steady ideal supply ; an external electrical load is coupled through a capacitor, so it draws no direct current. The input source has series electrical resistance . All voltages below are small departures from the operating point. An ideal fixed supply has zero incremental voltage and therefore becomes the reference node in the small-signal model.
Define and , where . Input voltage division and output Kirchhoff's current law give
Consequently the port voltage gain, overall source-to-output voltage gain, and load current gain magnitudes are
This current gain uses load electric current, not all the controlled-source electric current. It is also a different port definition from the historical emitter-to-collector current gain. Larger attenuates the input; smaller attenuates the output.
For a sinusoid input signal, use root mean square voltages. The power gain from accepted input signal power to useful load power is
Unlike , this tends to zero as either or . Differentiation gives
Thus matching the output electrical load maximizes delivered power in this unilateral resistive model. For fixed source voltage, input loading multiplies by ; the accepted-input power gain above excludes the loss in .
Choose , , , and . Then . With and root mean square, the input is and the inverted output has magnitude root mean square. Hence and : . These are calculated values of the chosen model, not historical measurements.
With the same parameters but , while . At , while . Neither current gain nor voltage gain alone establishes power gain.
Figure 1.
Chosen transistor model: transconductance, load and supply
. Original calculated illustration. Top: incremental electrical circuit. Lower left: the no-external-load direct current load line intersects three chosen local device curves. Lower right: port voltage gain, load current gain and power gain as changes. All parameters are stipulated teaching values. Source. Details.
For the direct current load line in the figure, choose , and , consistent with . Locally extend the model as . With the external electrical load isolated at direct current, its intersection with is . Keeping small compared with the available voltage headroom is essential; extrapolation to arbitrarily large signals would be unphysical.
At the chosen operating point the collector supply delivers : is dissipated in and in the output device. Under a small signal, that energy flow is redistributed to provide load power. The incremental controlled current source hides the supply's steady energy flow; it does not create energy. A real complete amplifier also needs its input biasing network and has further losses. This calculation establishes neither its total efficiency nor a universal law for point-contact transistors.
Transmission line 2026-10-18
A transmission line guides travelling voltage and current waves. Its distributed electrical properties determine its characteristic impedance. A mismatch at a terminal produces reflected waves; available power, delivered power and returned power are distinct quantities.
Transmitted power Created 2026-10-25 Updated 2026-11-05
The energy flux carried into a transmitted wave, integrated over the relevant cross section. The power transmission coefficient compares this with incident power. A displacement or field-amplitude transmission coefficient must be converted with the appropriate wave impedances; its squared modulus alone need not be the power fraction. This distinction applies both to electromagnetic waves and transverse string waves.
A transverse optical cavity mode is a resonant field pattern across the direction of propagation in an optical cavity. After propagation and reflection through a round trip, the mode reproduces its transverse shape up to a complex amplitude factor. Longitudinal order counts axial phase cycles; transverse order describes the pattern across the beam. Different transverse patterns can resonate at the same frequency, as in confocal transverse-mode degeneracy.
In an ideal paraxial cavity with suitable spherical mirrors, a Cartesian Hermite-Gaussian optical mode at its waist has field proportional to
where are Hermite polynomials, are nonnegative integers, and is the beam waist radius. The intensity is proportional to , not to the signed field. The primary photonics notes give these transverse solutions, their phase advance and lower-order patterns.[ref]
For , the intensity is a single Gaussian beam spot. For , , so intensity is proportional to . It vanishes on and its two maxima occur at , . The two lobes have opposite field signs even though both have positive intensity. The pattern has two crossing nodal lines and four intensity lobes.
Figure 1.
Intensity patterns of four ideal transverse cavity modes
. Computed Hermite-Gaussian waist-plane intensities for orders (0,0), (1,0), (2,0) and (1,1), each normalized to its own maximum. Equal color scales compare shape, not equal circulating power; intensity alone does not display field sign. Details.
For an ideal empty two-mirror cavity of length , set . On the near-planar stable branch with , the resonance frequencies are
The transverse contribution is a Gouy phase correction to the round-trip phase. Other branches require a consistent phase choice; the square root alone should not erase that choice. For an original example, and give and a one-order transverse spacing at fixed . Modes with the same are degenerate in this ideal symmetric model.
A proposed observation scans cavity length while recording both transmission peaks and a camera image of the transmitted beam. Translating or tilting the incident beam changes its overlap with different transverse modes; matching the incident wavefront and width favors the fundamental mode. A transmission peak alone cannot identify the spatial pattern, and an intensity image alone does not recover its phase. Finite apertures, astigmatism and mirror imperfections alter losses and split ideal degeneracies; state the cavity geometry and imaging plane when comparing observations.
Triple-point cell 2026-10-14
A triple-point cell turns phase coexistence into a reproducible reference for thermometer calibration. The NIST water-cell demonstration uses a sealed glass vessel containing water of specified isotopic composition and an open central thermometer well. Cooling this well with solid carbon dioxide and alcohol freezes an ice mantle while leaving liquid water and its vapor. The coolant is outside the sealed sample; the sample's vapor space does not communicate with room air.[ref]
In the actual NIST cell-comparison experiment, newly frozen mantles were compared with an aged reference mantle in a controlled maintenance bath. A warm aluminium rod melted a thin inner layer around the well, allowing the mantle to rotate freely and establishing an ice–water interface close to the sensor. A standard platinum resistance thermometer and a resistance bridge measured the electrical resistance ratio to a calibrated, temperature-controlled reference resistor. Readings at two currents permitted extrapolation to zero electrical power, correcting self-heating; measured immersion depths supplied hydrostatic pressure corrections. Comparing preparations over time tested stabilization rather than assuming freshly frozen ice was ready.[ref]
The inference is a reproducible fixed-point response for the thermometer, not a direct reading of three chemical potentials. The reference cell anchors the comparison; a water point alone does not determine a thermometer's response at every other temperature. The ideal argument excludes impurity and isotope variation, finite interface effects and unintended heat transfer; real cells also require adequate immersion and stable electrical references. Repeatability is evidence that these effects are controlled, not a reason to omit their uncertainty.
Since 20 May 2019 the kelvin has been defined through a fixed numerical value of the Boltzmann constant. The thermodynamic temperature of the water triple point is consequently a measured quantity with uncertainty, rather than an exact value imposed by the kelvin definition. Its continued use as an assigned reference on the International Temperature Scale of 1990 is a separate convention.[ref][ref]
Tunnel diode Created 2026-10-18 Updated 2026-10-20
A tunnel diode is a p-n junction with sufficiently heavy semiconductor doping on both sides to make a thin depletion region and permit substantial interband tunnelling. The neutral regions are degenerate semiconductors. Its distinctive forward current-voltage characteristic contains a peak followed by a valley: over part of the curve, increasing the applied electric potential difference decreases the electric current. The Esaki tunnel-diode experiment made this behavior experimentally concrete.
The useful quantity is the local slope, not the ratio of total voltage to total electric current. With conventional electric current entering the positive-voltage terminal, define
Negative differential resistance means , hence where defined. A forward operating point can still have , and absorbed power . A small voltage increase then gives a negative current increment; this does not make the total electric current negative or turn the device into an unlimited source of energy. The external supply sets the operating point and supplies the energy available for an electronic amplifier.
An original idealized construction explains the shape. Put the n-type semiconductor on the left and the p-type semiconductor on the right. Take as the elementary charge and . Increasing forward bias lowers the right-hand electron energy levels relative to the left. Denote the two reservoir electrochemical potentials by , so that . At zero temperature, occupied left-hand conduction band states extend up to ; empty right-hand valence band states start at . For transfer conserving electron energy, the available interval is
It is nonempty only when its upper endpoint exceeds its lower endpoint. Both an occupied initial quantum state and an empty final quantum state must exist at the same energy. The Pauli exclusion principle prevents transfer into an already occupied final quantum state.
For the original diagram, choose arbitrary energy units with , , and , where is in those units. The available interval has width
Thus , , , and . Initially forward bias opens a transfer window; further forward bias closes it by moving the right-hand valence band edge below the left-hand conduction band edge. This is a state-counting illustration, not a formula for a measured electric current.
Figure 1.
Tunnel diode: energy band alignment and occupied-to-empty state overlap
. Original chosen energy band construction, with n-type semiconductor on the left and p-type semiconductor on the right. Blue shading denotes occupied reservoir states; orange hatching denotes empty reservoir states. Green arrows mark equal-energy transfer. The central barrier and band bending are schematic; all energies are arbitrary, and the drawing is not an experimental image or measured band profile. Source. Details.
For reverse bias, the transfer direction changes: occupied right-hand valence band states can feed empty left-hand conduction band states. In the same construction, opens the interval for this reverse transfer. A narrow depletion region allows a large reverse quantum tunnelling electric current at small electric potential difference, whereas the ordinary Shockley diode equation predicts only a small reverse saturation electric current before diode reverse breakdown. At zero biasing, equal reservoir occupations give zero net electric current; quantum tunnelling does not require a net equilibrium flow.
A finite-temperature refinement replaces sharp occupation cutoffs with the Fermi-Dirac distribution. An illustrative weak-transfer expression is
Here describes allowed initial/final quantum states and their coupling, and are Fermi-Dirac distributions with the respective electrochemical potentials. The occupation difference follows by subtracting the reverse transfer factor from the forward one: . An overlap interval alone does not determine : transmission probability, density of states, crystal momentum selection and phonons can matter. A complete germanium calculation is more demanding than multiplying two constant density of states factors. At larger forward bias, ordinary carrier injection and diffusion supply a rising current branch even after direct band overlap is lost.
A current-voltage characteristic determines possible steady operating points; it does not alone determine their linear stability. Consider an ideal voltage source feeding a tunnel diode through a resistor , with a positive constant capacitance across the junction. Assume a quasistatic device relation and neglect inductance, transit delays, noise and heating. Kirchhoff's current law gives the original one-state model
A steady operating point satisfies : the device curve intersects the descending supply line. This is the source-side counterpart of a resistive load line. A small perturbation obeys
Thus the equilibrium point is locally attracting if and unstable if the inequality reverses. Equality requires higher-order analysis. Even on a negative differential resistance segment, a sufficiently small supply electrical resistance can stabilize this model. The assumption about the electrical circuit matters: an inductive or delayed circuit has additional state variables and may behave differently.
Choose an original toy forward characteristic, with no fitted device parameters:
where , and . For every , , so this entire forward curve absorbs positive total power. Nevertheless
The model therefore separates negative differential resistance from negative total . The corresponding peak and valley are at approximately and ; these voltages deliberately differ from the historical peak.
With and , the supply line is . The intersection equation factors exactly:
The three operating points are , and . Their values of are respectively , and . The outer two attract nearby trajectories; the middle one repels them. This is bistability in the specified one-state electrical circuit.
Figure 1.
Chosen tunnel diode curve and supply-line linear stability
. Original calculated current-voltage characteristics and trajectories of the stated quasistatic model. Filled green points attract nearby trajectories; the open red point repels them. The same negative-slope point becomes attracting when the supply electrical resistance is reduced and the source voltage adjusted. All values are chosen, not measured data or a fit to a historical device. Both panels use and the same toy device curve. Source. Details.
For the second panel, choose and . Now and
There is exactly one real operating point, again . Here , despite the device's own slope . With , the perturbation decays with time constant ; the unstable middle point of the first panel has growth time .
The one-state autonomous model supports switching between attracting operating points after a perturbation or parameter change; it cannot produce a nonconstant periodic orbit. A proposed oscillator needs additional dynamics. This limitation is useful: a load-line intersection establishes a possible steady reading, the slope test establishes local attraction in a specified model, and neither calculation alone predicts an oscillation frequency for a real tunnel diode.
Turbine 2026-11-05
A turbine extracts mechanical work from a flowing fluid through interaction with a rotating set of blades. Steam, hot gas or water changes its momentum while passing through the rotor, producing torque on the shaft. A steam turbine can drive an electrical generator in a thermal power station.
For steady axial through-flow in an ideal control-volume model, shaft torque is , the rate at which fluid angular momentum is removed. Here is the tangential velocity component and the radius. Shaft power is at angular speed . The relation connects blade-induced changes in flow direction with useful output; losses and operating conditions determine actual conversion efficiency.
Ultraviolet Created 2026-10-05 Updated 2026-10-20
Ultraviolet is electromagnetic radiation with wavelengths shorter than the violet end of ordinarily visible light. The CIE convention uses –, subdivided into UV-A at –, UV-B at – and UV-C at –. These divisions name intervals; they do not mark universal changes in every material's response. The boundary with visible light is not sharp, and other fields use near-, far-, vacuum- and extreme-ultraviolet divisions. [ref]. For example, NASA's Solar Dynamics Observatory observes extreme-ultraviolet bands below ; the CIE interval is therefore not the full extent of astronomical ultraviolet usage. [ref].
The CIE ultraviolet interval corresponds to frequencies about – and photon energies –, using vacuum wavelength and with Planck constant and speed of light . Shorter wavelength means larger energy per photon; larger irradiance means more incident power per area. These are different comparisons. At the same incident power, a ultraviolet beam has fewer photons per second than a infrared beam, even though each ultraviolet photon has more energy.
A common ultraviolet mechanism is photon absorption promoting an electron from a ground state to an excited state of a chemical atom or molecule. By contrast, many infrared absorption bands involve stretching or bending chemical bonds. For either mechanism, both the energy difference and the coupling to the incident electromagnetic field matter. One concrete example is the absorption discussed for butadiene: an electron moves between molecular orbitals, and the position of the absorption reveals their energy separation. Ultraviolet absorption can therefore probe molecular orbitals, while infrared spectroscopy probes many molecular motions. [ref].
Subsequent chemical reactions depend on the absorbing chemical substance and its environment; the label ultraviolet alone does not predict a reaction rate. At sufficiently short wavelength, a photon can cause photoionization if its energy exceeds the relevant ionization energy. There is no single wavelength that separates all ionizing from all nonionizing behavior for every chemical substance. Likewise, eventual heating after photon absorption is possible in both ultraviolet and infrared. The distinction is useful because different optical spectra expose different processes, not because the two ranges obey different laws of electromagnetism.
Ritter's 1801 observation used a chemical readout rather than a thermometer. In Caltech/IPAC's account, sunlight passed through a glass optical prism and silver chloride was placed in different parts of the optical spectrum. Darkening was weak toward red, stronger toward violet, and pronounced beyond the visible violet edge. The measured evidence was a change in the chemical substance's appearance at a spatial location with no visible color, establishing radiation beyond the eye's ordinary range. It was not a calibrated measurement of a universal ultraviolet optical spectrum. [ref].
A controlled modern interpretation of such a chemical test would compare equal exposure durations and matched fresh samples, keep an unexposed sample in darkness, monitor temperature, and distinguish scattered visible light from the intended short-wavelength beam with characterized filtering. These are proposed controls, not an assertion that Ritter performed them. Unequal sample preparation or heating can change a reaction rate. The optical prism, terrestrial atmosphere and sample response restrict which wavelengths the test detects. Darkening is a detector-weighted response, so its spatial maximum is not automatically the maximum of incoming radiant flux or of photon energy.
Thomas Larason and Jeanne Houston's NIST report documents a quantitative ultraviolet detector comparison. An argon source feeds a double-diffraction grating spectrometer; a shutter and mirrors deliver the selected band to a working-standard or test photodiode, successively at the same position. A beam splitter supplies a monitor photodiode. Amplifiers and voltmeters record detector and monitor simultaneously; shutter-closed readings provide dark baselines. The – scan, typically with bandpass, measures spectral responsivity. Monitor normalization suppresses source drift; known spectral lines calibrate wavelength. The report assesses temperature effects and unwanted light outside the band, weighted by detector response. The latter need not cancel between different spectral responsivities. [ref].
This determines electrical response without visual perception. Bandpass and spatial nonuniformity limit the calibration; aging and changed temperature can affect later use. The scan includes visible light and ultraviolet; no response below follows from it.
For a narrow beam, the idealized substitution calculation is
Here is spectral responsivity; and are dark-subtracted detector and monitor electric currents. This follows by writing for each detector and using the monitor to track changes in radiant flux. It assumes linear response, unchanged beam splitting and collection geometry, and a sufficiently narrow band. For an illustrative standard with , ratios and give . These invented arithmetic inputs illustrate the method; they are not NIST measurements.
An independent photon-counting model connects spectral responsivity to quantum efficiency. If is the number of collected electrons per incident photon, there is no internal multiplication, and is the elementary charge, then
At illustrative constant and , this gives about at and at . The ultraviolet readout is smaller in this model because there are fewer incident photons, not because their individual energies are smaller. Real quantum efficiency depends on wavelength, windows, absorption and carrier collection; a detector's band gap and construction determine its usable range. Constant across these two wavelengths is an analytical comparison, not a claimed specification of a real photodiode.
Figure 1.
Photon energy across conventional ultraviolet and infrared ranges, with a schematic detector-substitution experiment
. Details.
The curve is the calculated relation , and the shaded ranges use the stated CIE conventions. The lower diagram abstracts the detector comparison rather than reproducing an instrument drawing. Together with the infrared heat-balance illustration, it shows why a calibrated detector response, rather than what looks bright to an observer, is the bridge between invisible radiation and a quantitative measurement.
Virtual displacement 2026-11-05
A virtual displacement is an infinitesimal change of configuration compatible with the instantaneous mechanical constraints, evaluated at fixed time. It is a variation among admissible configurations, rather than necessarily the displacement made during a time step. In generalized coordinates, write
Substitution into the applied virtual work identifies the generalized forces conjugate to the coordinates.[ref]
An original moving-constraint example makes the fixed-time condition visible. Consider a particle constrained to the circle
For a virtual displacement, freeze and therefore ; first-order compatibility gives . For an actual motion, differentiation with respect to time instead gives
At with , every admissible virtual displacement has , while an actual velocity must have . If the circle is expanding at , the actual radial velocity is nonzero even though every virtual displacement is tangent to the instantaneous circle.
Consequently, an ideal radial constraint force can have zero virtual work but nonzero instantaneous power during this driven motion. Zero work on admissible variations is not the statement that a moving support never transfers energy. The example is a time-dependent holonomic constraint; the variations satisfy its instantaneous linearized condition. In a beam, the same distinction lets one impose zero endpoint virtual displacement while leaving the virtual endpoint slope free, as in the moment-free natural boundary condition for a beam.
Viscous fluid flow Created 2026-09-24 Updated 2026-11-05
Viscous fluid flow includes the transfer of momentum by internal viscous stresses. For an incompressible Newtonian fluid with constant dynamic viscosity , the extra stress is proportional to the rate-of-strain tensor:
Combining this relation with momentum conservation gives the Navier-Stokes equation. Other constitutive equations, including those for non-Newtonian fluids, give different stress responses.
A simple example is Couette flow between plates separated by , with one fixed and the other moving at speed . A steady linear profile produces uniform shear stress . The moving plate supplies power per area , which becomes viscous dissipation. [ref]
The Reynolds number compares advective momentum transport with viscous transport. Small values motivate Stokes flow; large values can still require thin viscous boundary layers near solid walls. Viscous flow therefore includes both smooth laminar flow and turbulent flow.
Viscous termination of a stretched string Created 2026-10-18 Updated 2026-10-20
A semi-infinite wave equation on a string with linear mass density , wave speed , and tension has positive characteristic mechanical impedance . At an end attached to a massless viscous damper of coefficient , displacement and transverse-force balance give the displacement reflection coefficient
Here is the fraction of mean incident power dissipated. A prescribed gives two positive damper coefficients, , with opposite reflected phases. Matching removes reflection.